Blonder tongue MUX-2D-QAM User manual
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
➥
❏
❏
❏
❏
❏
➥
➥
OUTPUT
Connector: 1x “F” Female
QAM Modulation Modes: 16, 32, 64, 128, 256, 512, and 1024
DVB Symbol Rate: Variable; 1 to 7 MSymbols/sec (MBaud)
Frequency Range: 54 to 864 MHz
QAM Tuning Per channel’s number from 2 to 135
RF Level: +45 dBmV
RF Level LCD Screen Error: ± 2 dB
RF Level Adjustment Range: 33 to 47 dBmV
Frequency Stability: ± 10 kHz over 32 to 122 °F (0 to 50 °C)
Frequency Tolerance: ± 0.5 kHz @ 77 °F (25 °C)
Amplitude Flatness: ± 0.25 dB (over 6 MHz channel)
Phase Noise: -98 dBc (@ 10 kHz)
Spurious: -60 dBc
Broadband Noise: -75 dBc (@ +60 dBmV output level, 4 MHz bandwidth)
Impedance: 75 Ω
Return Loss: 12 dB
Spectral Inversion: Auto Recognition
Carrier Suppression: 55 dB
SNR: Greater than 40 dB
MER: Greater than 40 dB
I/Q Phase Error: Less than 1 degree
I/Q Amplitude Imbalance: Less than 1%
EAS Looped Output
Connector:
Standard:
Trigger Mechanism:
1x BNC Female
ASI
5-12 VDC or Dry Contact Closure
INPUT
Connectors
8VSB/QAM module:
Emergency Alert System (EAS):
2x “F” Female
1x BNC Female
Standards
8VSB:
QAM:
ASI (EAS Input):
ATSC Digital Television A/53E
ITU-T J.83 - Annex A & B (64 and 256 QAM)
1x DVB-ASI; EN 50083-9
SD single program broadcast
MPEG2 or 4 video and AC-3 Dolby® Audio
8VSB Mode
Tuning Range:
Data Rate:
Bandwidth:
Power Level:
UHF (NTSC Ch. 14-69), VHF (NTSC Ch. 2-13)
19.392 Mbps
6 MHz
-20 to +20 dBmV
QAM Mode
Tuning Range:
Data Rate:
Bandwidth:
Power Level:
CATV (NTSC Ch. 2-135)
38.8 Mbps (QAM 256); 26.97 Mbps (QAM 64) – Auto Detect
6 MHz
-15 to 20 dBmV (@ QAM 256)
-20 to 20 dBmV (@ QAM 64)
Impedance:
75 Ω
General
Dimensions (W x D x H): 19.0 x 14.3 x 1.75 inches (483 x 363 x 44 mm)
Power: 105 to 240 VAC/50 to 60 Hz
Power Dissipation: 36 W
Weight: 5.1 lbs (2.31 kg)
Operating Temperature: 32 to 122 °F (0 to 50 °C)
Storage Temperature: -13 to 158 °F (-25 to 70 °C)
Operating Humidity: 0 to 95% RH @ 35 °C max, non-condensing
Storage Humidity: 0 to 95% RH @ 35 °C max, non-condensing
Alarms/Monitoring/Control
Local Monitoring:
Local Control:
Front-panel 16-character, 2-line LCD screen
Front-panel Navigational Key-pad
Remote Monitoring/Control: Not available
Initializing MUX
Please wait… MUX Initialized
Updating MUX
Please wait…
MUX Output
Has Been Updated!
MUX OUTPUT MENU
Status: OK
MUX OUTPUT MENU
Overflow Error!
tupq
tu
pq
tu
pq
pq
Entry Accepted
NOTES:
[1] In the Input Module menus "*" means the program was filtered.
[2] The Gray Mode is available in ITU-A only.
[3] In the MUX OUTPUT menu "*" means the program was remapped.
ut
8VSB INPUT# 2
MENU
u
IN2:TSID
ut
IN2:MJR Offset
0000
ut
IN2:PID Offset
0000
ut
IN2:Baud Rate
5.3811 MBd/sec
ut
IN2:Channel No.
000
ut
IN2:RF MODE
Air Broadcast
ut
IN2:Modulation
8VSB Off-Air
ut
IN2:Prog# 3
*13-3 V-ME
ut
IN2:Prog# 2
*13-2 KIDS
ut
IN2:Prog# 1
13-1 WNET-HD
u
u
t
t
ut
IN1:Prog#2
5-2 WWOR
8VSB INPUT# 1
MENU
u
IN1:TSID
ut
IN1:MJR Offset
0000
ut
IN1:PID Offset
0000
ut
IN1:Baud Rate
5.3811 MBd/sec
ut
IN1:Channel No.
000
ut
IN1:Prog#1
5-1 WNYW
u
t
t
u
ut
IN1:Modulation
8VSB Off-Air
Normal
CATV QAM
64B
CATV QAM
256B
CATV QAM
32A
8VSB Off-Air
ut
IN1:RF MODE
Air Broadcast
Normal
CATV
Standard
CATV HRC
CAV IRC
Air Broadcast
ut
ut ut
ITU-A
I204, J1
I1, J204
I2, J102
I3, J68
I4, J51
I6, J34
I12, J17
I17, J12
I34, J6
I51, J4
I68, J3
I102, J2
ITU-B
I128, J1
I128, J2
I64, J2
I128, J3
I32, J4
I128, J4
I16, J8
I128, J5
I8, J16
I128, J6
I4, J32
I128, J7
I2, J64
I128, J8
I1, J128
I128,J1
QAM MENU
Status: OK
QAM: MODE
Normal
Normal
PRBS
23M
PRBS 23
PRBS
15M
PRBS 15
Inverted
Off
Normal
QAM:
MODULATION
QAM 256
16
32
64
128
256
512
1024
256
QAM: ALPHA
12%
12%
15%
18%
12%
QAM: INTERLEAVE
I128, J1
QAM: ENCODE
MODE
ITU-T Annex B
ITU-T
Annex A
ITU-T
Annex B
ITU-T
Annex B
DAVIC
DVB
QAM: GRAY MODE
DAVIC
DAVIC
QAM: BAUD RATE
5.3605
5.3605 MBd/Sec
Range: 1 to 6.9
u
t
u
t
u ut ut utut ut ut
RF OUTPUT
MENU
Status: OK
RF: FIRMWARE
Version 1.0
2 to 135
RF: OUTPUT CH#
2
2
RF: OUTPUT
MODE
NTSC Standard
Standard
NTSC
HRC
IRC
Standard
RF: OUTPUT
LEVEL
60 dBmV
45 dBmV
Range: 33 to 47
t
t
u ut ut ut
u
u
MUX OUTPUT
Status: OK
MUX: Prog# 1
5-1 WNYW
MUX: *Prog# 3
13-1 WNET-HD
MUX: VERSION
01:01:0O:01:0O
MUX: ADDRESS
16777215
MUX: RESCAN
ALL
NO
YES
NO
MUX: Prog# 2
5-2 WWOR
MUX: PSIP
ENABLE
YES
YES
NO
YES
MUX:OUT TSID
00001
MUX: FACTORY
DEF
NO
YES
NO
MUX:CVCT
ENABLE
NO
YES
NO
u ut ut utut ut ut utut ut
t
t
u
u
COMMENTS:
• Factory default values, when applicable, are highlighted in black in the diagram above.
DIAGRAM #1
tu
pq
p
q
tu
pq
pq
tu
pq
pq
tu
pq
tupq
IN1: Prog# 2
6-2 WBTL-SD
IN1: Prog# 2
* 6-2 WBTL-SD
INPUT# 1
Stream Present
INPUT# 1
Stream Absent
tu
pq
tupq
tu
pq
tupq
tu
pq
t u p q
tu
pq
pq
tu
pq
pq
tu
pq
pq
tu
pq
pq
QAM MENU
Status: OK
QAM MENU
Status: CommError!
tu
pq
pq
tu
pq
tupq
tu
pq
pq
tu
pq
pq
tu
pq
pq
tu
pq
pq
tu
pq
tupq
tu
pq
pq
tu
pq
pq
tu
pq
pq
MUX:Prog #1
6-1 WBTL-HD
MUX:*Prog #2
6-2 WBTL-SD
This manual suits for next models
1
Table of contents
Other Blonder tongue Multiplexer manuals
Popular Multiplexer manuals by other brands
Signametrics Corporation
Signametrics Corporation SM4020 Operator's manual
American Dynamics
American Dynamics Multivision Quest DMV14Q Specifications
Omnitron Systems
Omnitron Systems iConverter 4xT1/E1 user manual
Actisense
Actisense PRO-MUX-2 Configuration guide
Velleman
Velleman VQS4RT4 quick start guide
Alien
Alien Nexus ALX-2530 user guide
Cronyx
Cronyx E1-XL/B-IP Installation and operating manual
General DataComm
General DataComm SpectraComm SRM-6 Installation & operation manual
Racal Instruments
Racal Instruments 1260-38T user manual
LINK-MI
LINK-MI LM-SH61 user manual
Quadra Plus
Quadra Plus VPU100 manual
GE
GE JungleMUX SONET 86447 installation manual