Blucave TDD-10 User manual

1
5
2
6
3
7
4
8
DISASSEMBLING:
Ensure the Drill Driver is switched off before trying to
remove the Controller. Press the unlock symbol located
on the Controller and then turn the ToolBod away from
the Controller.
DRILL BITS
The BluCave Drill Driver Accessory
Kit (Sold Separately) contains a
variety of drill bits & screw driver
bits that are ideal for most DIY
projects.
MOUNTING:
Grip the chuck collar with one
hand and turn the chuck body anti-clockwise with your
other hand to open the jaws. See
fig. 2 Insert required bit into the
jaws ensuring ample gripping area
for the jaws. Tighten the chuck by
gripping the chuck collar with one
hand and turning the chuck body
clockwise with your other hand.
See fig. 3
Run the Drill Driver under no load to ensure the bit is
fitted correctly and runs true.
REMOVING:
Grip the chuck collar with one hand and turn the chuck
body anti-clockwise with your other hand to open the
jaws. Remove the bit.
Caution: the bit may be hot to touch.
OPERATION:
All types of BluCave 18V DC Controllers (Ni-Cd, NiMH &
Li-Ion) will fit all BluCave DC ToolBods.
APPLICATIONS
The Drill Driver can be used with timber, plastic and
metal.
SWITCHING ON/OFF
Ensure the Controller and ToolBod are fitted correctly
and the bit is securely in place before operating.
Squeeze the trigger to start the Drill Driver.
Keep the trigger depressed to keep the drill operating.
Release the trigger to stop the Drill Driver.
SPEED
The Drill Driver is a variable speed ToolBod. As you
squeeze the trigger on your Controller the speed will
vary from slowest to fastest at maximum depression.
Low speed is ideal for delicate materials when minimum
power and greater control is required.
Medium speed is suitable when a balance of power and
control is needed.
High speed is ideal for hard materials and produces fast
drilling when accuracy is not critical.
TORQUE SETTINGS
Torque is the twisting force the drill applies to the
bit in the jaws. The Drill Driver is fitted with a torque
control ring at the front of the ToolBod. Torque control
adjustment helps drive fasteners to a pre-determined
and repeatable tightness. Without torque control a
screw can be over tightened, too
loose or driven too far into the
work surface.
Lower torque settings are suitable
for small screws and driving into
soft materials.
Higher torque settings are suitable for large screws and
driving into hard materials. To set the torque control,
rotate the torque ring aligning the number setting with
the indicator on the top of the ToolBod. Higher numbers
increase twisting force. See fig. 4
Always start at a low level of torque. The lower the
number setting, the lower the torque force is applied.
If more force is required to drive a screw increase the
torque setting gradually and continue. If multiple
screws of the same size are to be driven into the same
material you can now continue at the same torque
setting.
STORAGE:
ToolBods come with their own unique storage dock
for compact and protective
housing inside the BluCave
Carry Cabinets See Fig. 5.
WELCOME:
CONGRATULATIONS
YOU’RE NOW A
BLUCAVER!
You’re one of the growing community who have
embraced the BluCave work zone!
The BluCave Drill Driver is one of the many
convenient DC ToolBods (cordless power
tool bodies) that clicks into your BluCave DC
Controllers.
REMEMBER:
Comply with all safety precautions and
instructions when using your BluCave products.
• When in doubt always ask for advice.
• Always wear protective clothing.
• Always work in an uncluttered environment.
TIPS:
To prevent splintering always start by drilling a
pilot hole approximately 25% of the final size you
require. Commence the drilling of your final hole
from the reverse side of your work piece. When
you are approximately half way though, rotate and
finish the remainder of the hole from the other
side of your work piece.
ENJOY:
Need some inspiration or support? The BluCave
website opens-up a whole new world of DIY.
You can ask for help, gain real time product
information, share ideas and receive regular
updates on special BluCave offers.
ACCESSORIES: A set of accessories is available as a
starter kit for each BluCave ToolBod.
VERSATILE CARRY CABINETS: The BluCave Carry
Cabinets provide storage options for the complete
BluCave range and even your existing tools. They
can be used as portable cases or mounted on the
BluCave Rail as stylish cabinets.
BOOSTERS: You can even ‘boost’ your BluCave to
include power, light and audio.
Visit BluCave.com to view the complete work zone.
DID YOU KNOW…
The Drill Driver can be used for screw driving and
drilling into timber, plastic and metal.
SYMBOLS:
W Watts
Kg Kilograms
g Grams
dB(A) Decibels (A weighted)
m/s² Vibration
⎓Direct Current (DC)
V Volts
mAh Milliampere Hour
min-1 Revolutions or reciprocations per minute
n0 No load speed
Pa Pascals
Bar Bars
mm Millimetres
ASSEMBLY:
Caution: All assembling, mounting, disassembling and
removing should be done with the Drill Driver turned off.
TOOLBOD & CONTROLLER
Caution: BluCave offer both AC (powered) and DC
(cordless) operated Controllers and ToolBods.
AC ToolBods will only operate with an AC Controller
and DC ToolBods will only operate with a DC Controller.
For simple identification look for the appropriate
colour marking with green representing AC and orange
representing DC.
ASSEMBLING:
Align the fixed hook (Grey) of the Controller into the
corresponding recess on the underside of the ToolBod.
Once located and engaged, close
the two faces of the Controller and
ToolBod together until they click
into place. (It’s as easy as Hook,
Swing and Click) See Fig. 1.
GETTING TO KNOW YOUR
BLUCAVE POWER TOOL:
DRILL DRIVER ORIGINAL
INSTRUCTIONS
MODEL NO: TDD-10
Assembly.......................................................................
Toolbod and Controller.................................................
Drill Bits.........................................................................
Operation......................................................................
Applications..................................................................
Switching On/Off..........................................................
Speed............................................................................
Torque Settings............................................................
Storage.......................................................................
Cleaning/Servicing.....................................................
General Safety Warnings..............................................
Sander Safety Warnings...............................................
1
1
2
3
3
3
4
4
6
7
9
13
WARRANTY:
This Batavia product comes with a 2 year warranty.
Dear Client, all Batavia products have undergone a strict
quality process. If for any reason this product is not
working or damaged, please contact our Client Service
Centre. Please retain your original receipt of purchase.
The Batavia warranty covers all defects in workmanship
or materials for a two year period from the date of
purchase. The Batavia warranty does not cover any
malfunction, or defect resulting from misuse, neglect,
alteration, or repair.
Deutschland | Kundenservice
Montag bis Freitag von 9 bis 17 Uhr
01805 937832*
Other European countries | Customer Services
Monday till Friday from 8 am until 4 pm
00800 66477400
Website: www.batavia.eu | Email: [email protected]
*Nur €0,14 /Minute aus dem dt. Festnetz,
max. €0,42/Minute aus den Mobilfunknetzen.
CLEANING/SERVICING:
The Drill Driver can be wiped over with a damp cloth but
must be completely dry before operating.
Ensure the ventilation slots are kept free from dust.
Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure
that the safety of the power tool is maintained.
5
1
2
9
3
5
4
8
7
6
DC CONTROLLER (Sold Seperately)
1. Carrying Strap
2. Magnet
3. Trigger
4. Forward/Reverse Selector
5. Controller Unlock Button
ANGLE GRINDER TOOLBOD
6. Chuck Body
7. Chuck Collar
8. Torque Ring
9. Bit Holder
1
2
3
4
DC_Drill TDD-10 EU EN REV 07.indd 1 22/06/2004 2:00:32 AM

10
11
13
14
16
17
19
20
9 12 15 18
TECHNICAL DATA
Drill Driver MODEL: TDD-10
Voltage 18V
No Load Speed 0-550 min-1
Chuck 10mm
Capacity Timber 20mm
Capacity Metal 10mm
Weight 0.78Kg
BluCave tools are for private use only and are not suitable
for commercial / professional / continuous use.
Measured values determined according to EN 60745
Typically the A-weighted noise levels of the product are:
Sound Pressure Level LpA 64.45 dB(A)
Sound Power Level LWA 75.5 dB(A)
Uncertainty KpA 3 dB(A)
Uncertainty KWA 3 dB(A)
Wear Hearing Protection!
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessary.
It becomes wedged in the workpiece.
• Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
• Hold the machine with a firm grip. High reaction
torque can briefly occur while driving
• Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn
or explode.
• Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam
and lead to loss of control over the power tool.
• Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with the
appliance.
Distributed by:
Batavia GmbH
Blankenstein 180
7943 PE Meppel - Netherlands
Office phone: [phone]
www.batavia.eu
GENERAL POWER
TOOL SAFETY
WARNINGS
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. WORK AREA SAFETY
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. ELECTRICAL SAFETY
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. PERSONAL SAFETY
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. POWER TOOL USE AND CARE
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk
harmful to one’s health and cause allergic reactions,
lead to respiratory infections and/or cancer.
Materials containing asbestos may only be worked by
specialists.
• Provide for good ventilation of the working place.
• It is recommended to wear a P2 filterclass
respirator.
• Observe the relevant regulations in your country for
the materials to be worked.
• Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and
Storage, set the rotational direction switch to the
centre position. Unintentional actuation of the On/Off
switch can lead to injuries.
• Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
• Wear ear protectors. Exposure to noise can cause
hearing loss.
of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. BATTERY TOOL USE AND CARE
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. SERVICE
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
WARNING Read all safety warnings designated by the
symbol and all instructions.
DRILL SAFETY WARNINGS:
• Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
• Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
• When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
• If operation is dusty, also wear a dust mask.
• Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line causes
property damage or may cause an electric shock.
• Switch off the power tool immediately when the tool
insert jams. Be prepared for high reaction torque that
can cause kickback.
—The tool insert jams when:
The power tool is subject to overload OR
• This appliance is not intended for use by young
children or infirm persons. Adequate supervision by a
responsible person must be provided to ensure that
they do not play with the appliance.
• Keep children and visitors away. Visitors should wear
safety glasses and be kept a safe distance from work
area. Do not let visitors contact tool or extension cord.
• Do not open the battery. Danger of short-circuiting.
• Protect the battery against heat, e. g., also against
continuous sun irradiation and fire. There is danger of
explosion.
• In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
• When the battery is defective, liquid can escape and
come into contact with adjacent components. Check
any parts concerned. Clean such parts or replace them,
if required.
• Use the battery only in conjunction with your BluCave
power tool. This measure alone protects the battery
against dangerous overload.
• Dusts from materials such as lead-containing
coatings, some wood types, minerals and metal can be
Vibration total values (triaxial vector sum) determined
according to EN 60745
Drilling into
Metal
Vibration emission value ah,D= 0.81 m/s2
Uncertainty K =1.5 m/s2
The values given are valid for nominal voltages of 18V.
For lower voltage and models for specific countries
these values can vary.
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another.
The declared vibration total value may also be used in
a preliminary assessment of exposure. The vibration
emission during actual use of the power tool can differ
from the declared total value depending on the ways
in which the tool is used. Safety measures to protect
the operator should be identified that are based on an
estimation of exposure in the actual conditions of use
(taking account of all parts of the operating cycle such
as the times when the tool is switched off and when it
is running idle in addition to the trigger time).
WARNING - To reduce the risk of injury during
operation, always read the instructions.
Always wear hearing protection. The effects of noise
can cause hearing loss.
Always wear a dust mask. When working with wood
and other materials, harmful dust may be generated.
Work with asbestos containing materials is not
permitted!
Always wear safety glasses. When working with
electric power tools, sparks, splinters, chips and dust
particles may be generated and these can cause loss of
sight.
Symbols
The following symbols are important for reading and un-
derstanding the operating instructions. Please take note
of the symbols and their meaning. The correct interpre-
tation of the symbols will help you to use the machine in
a better and safer manner.
EC-Declaration of conformity
We, the undersigned Batavia GmbH, Blankenstein 180,
NL-7943PE Meppel, declare by our own responsibility
that the product Drill Driver, Item-No 7060536, Model Nr.
TDD-10-1:
Is according to the basic requirements, which are defined
in the European Directives Electromagnetic Compatibility
2004/108/EC (EMC).
Is according to the basic requirements, which are defined
in the European Directives, European Machinery Directive
2006/42/EC.
For the evaluation of conformity, the following
harmonized standards were consulted:
EN 60745-1: 2009+A11, EN 60745-2-1: 2010,
EN 55014-1:2006/A2:2011,
EN 55014-2:1997/A2:2008,
EN 61000-3-2:2006/A1:2009, EN 61000-3-3:2008
Meppel, 01 september 2011
Meino Seinen, QA Representative
Batavia GmbH, Blankenstein 180,
7943 PE Meppel, Netherlands
BLUCAVE.COM
© Demain International P/L 10/2011TDD-10-EU-EN REV 07
DC_Drill TDD-10 EU EN REV 07.indd 2 22/06/2004 2:00:33 AM