Blue Star Column User manual

INSTALLATION MANUAL
Column Refrigerator & Freezer
Part # R-000046 revision 0 © Prizer Painter Stove Works, Blandon, PA 19510

bluestarcooking.com 3
Contents
Safety Informaon 4
Site Preparaon 6
Panel Preparaon 8
Installaon Instrucons 10
Step 1—Uncrate and Inspect Product 10
Step 2—Remove Skid 10
Step 3—Hook up Electrical and Water 11
Step 4—Levelling 11
Step 5—Aach Plasc Connecng Brackets 11
Step 6—Install Two Appliances Side-by-Side 12
Step 7—Aach Wall Blocking 13
Step 8—Install Shoulder Bolts and Set Screws 13
Step 9—Install Panel (Panel-Ready Models) 14
Step 10—Move Appliance into Posion 14
Step 11—Install An-Tip Brackets 14
Step 12—Adjust Panel ( Panel-Ready Models) 16
Step 13—Aach Appliance to Cabinetry 16
Step 14—Aach Door Handle 17
Step 15—Aach Venng Grill 17
Tesng and Inial Startup 18

4(800) 449-8691
Safety Informaon
Electrical Shock Hazard
Follow these basic precauons:
• Plug into a grounded three-prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all parts and panels before operang.
• Use nonammable cleaner.
• Keep ammable materials and vapors, such as gasoline,
away from refrigerator.
• Use two or more people to move and install refrigerator.
Failure to follow these instrucons can result in death,
electrical shock, or re.
Important: Child entrapment and
suocaon are not problems of
the past. Junked or abandoned
refrigerators are sll dangerous
even if they will sit for a few days.
Before you throw away your old
refrigerator or freezer, do the
following:
• Take o the doors.
• Leave the shelves in place so
that children may not easily
climb inside.
Suocaon Hazard
Remove doors from old refrigerators. Failure to follow these
instrucons can cause death or brain damage.
Please read and obey the following types of safety messages to
ensure your refrigerator is installed and operated as safely as
possible:
Will cause serious injury or death if instrucons are not
followed.
Can cause serious injury or death if instrucons are not
followed.
Can cause minor injury or product damage if instrucons are
not followed.
DANGER
WARNING
CAUTION
WARNING
DANGER

bluestarcooking.com 5
Important: Le coincement et
l'étouement des enfants ne sont
pas des problèmes du passé. Les
réfrigérateurs mis au rebut ou
abandonnés restent dangereux
même s'ils doivent reposer
pendant quelques jours. Avant de
jeter votre ancien réfrigérateur ou
congélateur, observez les
consignes suivantes:
• Déposer les portes.
• Laisser les étagères en place
pour que les enfants ne puissent
pas grimper facilement à l'intérieur.
Renseignements sur la sécurité
Risque d'étouement
Déposer les portes des anciens réfrigérateurs. Le non-respect
de ces instrucons peut entraîner la mort ou des lésions
cérébrales.
Risque de choc électrique
Observer les précauons de base suivantes
• Brancher l'appareil à une prise triphasée mise à la terre.
• Ne pas retirer la broche de mise à la terre.
• Ne pas utiliser d'adaptateur.
• Ne pas utiliser de rallonge.
• Débrancher l'alimentation avant l'entretien.
• Remettre en place toutes les pièces et tous les panneaux
avant d'utiliser le produit.
• Déposer les portes de votre ancien réfrigérateur.
• Utiliser un nettoyant ininflammable.
• Garder les matières et les vapeurs inflammables, comme
l'essence, à l'écart du réfrigérateur.
• Deux personnes ou plus doivent déplacer et installer le
réfrigérateur.
Le non-respect de ces instructions peut entraîner la mort, un
choc électrique ou un incendie.
Veuillez lire et observer les types suivants de messages de
sécurité pour vous assurer que votre réfrigérateur est installé
et ulisé de la façon la plus sécurisée possible:
Provoque des blessures graves, voire la mort, si les instrucons
ne sont pas observées.
Peut entraîner des blessures graves, voire la mort, si les
instrucons ne sont pas observées.
Peut entraîner des blessures légères ou des dommages sur
produit si les instrucons ne sont pas observées.
DANGER
AVERTISSEMENT
MISE EN GARDE
AVERTISSEMENT
DANGER

6(800) 449-8691
Site Preparaon
Cabinet Opening Dimensions
30” Refrigerator or Freezer
Height: 84” (2134 mm)
Width: 29-5/8” (752 mm)
24” Refrigerator or Freezer
Height: 84” (2134 mm)
Width: 23-5/8” (600 mm)
18” Freezer
Height: 84” (2134 mm)
Width: 17-3/4” (451 mm)
30” Refrigerator with 30” Freezer
Height: 84” (2134 mm)
Width: 59-1/8” (1502 mm)
30” Refrigerator with 24” Freezer
Height: 84” (2134 mm)
Width: 53-1/4” (1352 mm)
30” Refrigerator with 18” Freezer
Height: 84” (2134 mm)
Width: 47-1/4” (1200 mm)
24” Refrigerator with 24” Freezer
Height: 84” (2134 mm)
Width: 47-1/4” (1200 mm)
24” Refrigerator with 18” Freezer
Height: 84” (2134 mm)
Width: 41-3/8” (1051 mm)
Cabinet Opening Depth Dimensions
Depth: 24-1/4” (616 mm) minimum plus panel thickness
for a panel-ready ush installaon. For example, if the
panel thickness is 3/4” (19 mm), the minimum depth
should be 24-1/4” + 3/4” = 25” (635 mm). Maximum
allowed panel thickness is 1-1/8” (29 mm).
Depth: 25-3/8” (645 mm) minimum for a stainless/painted
door ush installaon.
Depth: 23-1/4” (591 mm) minimum for a stainless/painted
door proud installaon.
Important: The cabinet enclosure must be securely
aached to the kitchen wall to assure the stability of the
appliance.
W
Top View
Front View
Side View
Opening Width
H
Opening Height
Opening Depth
Frameless Cabinetry Framed Cabinetry
W
3-1/2” (89)
Finished
Return
W
3-1/2” (89)
Finished
Return
Important: 3-1/2” (89 mm) nished returns will be visible
and should be nished to match cabinetry.

bluestarcooking.com 7
Electrical
Locaon: The electrical outlet should be located in
the area marked “Electrical” in Figure
1*.
The electrical outlet may also be located
in a cabinet adjacent to the enclosure.
However, an access hole would need to
be created in the back le corner of the
enclosure to route the power cord.
Requirements: The electrical outlet must be on a
dedicated non-GFI AC 110-120V, 60Hz,
15 amp circuit for each appliance and
accept a three-prong grounding plug. A
dedicated 15A circuit breaker should
also be installed and should be easily
accessible so that it can be easily
switched o before performing any
installaon or maintenance.
Plumbing
(For Freezer Models Only)
Locaon: The water line should be located in the
area marked “Water” in Figure 1*.
Requirements: The water line must use 1/4” OD
copper or PEX tubing and have 36” of
excess line. The appliance is provided
with a water adapter elbow which is
suitable for the recommended water
pressure and complies with applicable
food and water regulaons.
Water Pressure: The water pressure must be between
7.25-72.5 psi.
Important: The water line cannot be exposed to
temperatures below freezing.
Connect the water line to the household water supply with
an easily accessible shut-o valve, not a self-piercing valve.
Purge the water line before connecng it to the
refrigerator. This will remove any debris that may be
present.
Site Preparaon
Electrical Water
5” Max.
W
Figure 1
* Reference the Site Prep Guides for detailed
informaon regarding your specic installaon.
Electrical Shock Hazard
Electrical outlet must be checked by a qualied electrician to
conrm it meets all applicable electrical codes. Failure to
follow these instrucons can result in death, electrical
shock, or re.
CAUTION
Risque de choc électrique
La prise électrique doit être vériée par un électricien
qualié pour conrmer qu'elle est conforme aux codes
électriques applicables. Le non-respect de ces instrucons
peut entraîner la mort, un choc électrique ou un incendie.
MISE EN GARDE

8(800) 449-8691
Prepare the Door Panel
The dimensions of the panels are indicated in the table to the
le. Brackets and associated hardware are provided with the
product and must be aached to the panel as indicated.
• Draw a vercal center line on the back of the panel from
top to boom.
• Mark the locaon of the holes from the top edge of the
panel and vercal center line following the values in the
table on the next page.
• Posion the brackets on each set of marks and conrm
they are aligned. If you choose to drill small pilot holes for
the screws, pay special aenon to not drill through the
thickness of the panel enrely.
• Screw the brackets in place.
• If using a custom handle, please refer to the mounng
instrucons for that handle. The handle may need to be
installed on the panel prior to installing the panel onto the
appliance.
4
5 6
Panel Preparaon (Panel-Ready Models)
1
Panel Dimensions
Descripon Width (1) Width (2)
18” single Column 17-1/2”
(445 mm)
24” single Column 23-3/8”
(594 mm)
30” single Column 29-3/8”
(746 mm)
18” + 24” joined Columns 17-1/2”
(445 mm) 23-1/2” (597 mm)
18” + 30” joined Columns 17-1/2”
(445 mm) 29-3/8” (746 mm)
24” + 24” joined Columns 23-7/16”
(595 mm) 23-7/16” (595 mm)
24” + 30” joined Columns 23-1/2”
(597 mm) 29-3/8” (746 mm)
30” + 30” joined Columns 29-3/8”
(746 mm) 29-3/8” (746 mm)
Panel height: 79-7/8” (2029 mm) to match a 4” cabinet toe
kick. This is the minimum height from the oor to allow
proper venlaon of the appliance. The panel height can be
adjusted to match a cabinet toe kick up to 7-3/4” (197 mm)
from the oor.
Panel thickness can range from 3/4” (19 mm) to 1-1/8” (29
mm). In the case of a Shaker-style panel the panel may be
thinner than 3/4” (19 mm), however, a minimum thickness of
3/4” (19 mm) is required where brackets are screwed to the
back of the panel.
Maximum weight for each panel is 75 lb (34 kg).
The hinging mechanism is considered to be `Zero-clearance`.
The panel widths specied above assume the minimum
enclosure width is being used and a 1/8” (3.5mm) reveal is
desired around the panels. Adjust your panel dimensions
accordingly to your own design criteria considering your
enclosure width and your reveal. Minimum reveal/gap should
not be less than 1/16” (1.5mm ).

bluestarcooking.com 9
Panel Preparaon (Panel-Ready Models)
30” 24” 18”
A* 29-3/8” (747 mm) 23-3/8” (594 mm) 17-1/2” (445 mm)
B13-1/2” (343 mm) 10-13/16” (275 mm) 7-7/8” (200 mm)
A
BB
1/2” (13)
Hole locaons. Dimensions in ( ) are mm.
1-5/16” (34) 1-5/16” (34)
4-3/8” (111)
6-1/2” (165)
27-1/4” (691)
Minimum 76-1/8” (1934)
50” (1271)
70-3/4” (1797)
* “A” dimensions are for a single appliance installaon. See page 8 for panel
widths for side-by-side appliance installaons.
Top of Panel
Panel Hole Mounng Posions

10 [phone]
Installaon Instrucons
Tip Over Hazard
Product ps easily when not completely installed. Use two or
more people to move and install product. Failure to follow
these instrucons can result in death or serious injury.
Risque de renversement
Le produit pointe facilement lorsqu'il n'est pas complètement
installé. Deux personnes ou plus doivent déplacer et installer
le produit. Le non-respect de ces instrucons peut entraîner la
mort ou des blessures graves.
Tools and Materials
• Mounng kit (included)
• An-pping kit (included)
• Lateral connecon kit (included)
• 1/8” hex key (included)
• Rivet tool
• Phillips screwdriver
• Screws to aach brackets (customer supplied)
• Power drill
• 1/8” drill bit (for wood stud wall)
• 5/16” drill bit (for masonry walls)
• Stud nder
• Tubing cuer (for water line)
• 3’ of 1/4” OD copper or PEX tubing (for water line)
• Saddle valve (for water line)
• 11/16” (17mm) open end wrench
• 3/4” (19mm) open end wrench
• 1/2” (13 mm) socket
• Level
• Gloves
• Safety glasses
• Before transporng the appliance, check access to the
locaon where it will be installed (door size, maneuvering
space in stairwells, etc).
• Use a pallet-jack or appliance cart to move the appliance
to the installaon site before removing the appliance
from the pallet. The appliance should always be
transported in an upright posion. If this is not possible,
transport the appliance on its back.
Step 1 — Uncrate and Inspect Product
• Before starng the installaon, uncrate and inspect the
product. Remove the packing materials but do not discard
the mounng kit, an-pping kit, lateral connecon kit,
joining kit on back of freezer, venng grille, handle pack
(if ordered) and associated hardware.
Step 2 — Remove Wood Pallet
Important: Delicate oors should be protected with plywood,
hard-board or similar material panels.
• Remove the wood pallet by removing the four shipping
bolts (1) with an appropriately-sized wrench or socket.
Discard the shipping bolts.
• Remove the front and rear shipping brackets (3, 4). For
the front bracket (3), the rear wheel adjusng bolt (2)
may need to be loosened with a 1/2” (13 mm) socket or
wrench. Avoid over-torqueing this bolt at its stop points
so as to not damage the rear leveling system.
• Retract the front leveling feet with a 11/16” (17 mm)
open end wrench.
• From the back of the appliance using a suitable, heavy-
duty appliance dolly, take the appliance o the pallet and
place it on the oor.
WARNING
AVERTISSEMENT
CAUTION
The appliance should always be transported in an upright
posion. Avoid pping it onto its front side.
MISE EN GARDE
L'appareil doit toujours être transporté en posion vercale.
Évitez de le faire basculer sur sa face avant.

bluestarcooking.com 11
Installaon Instrucons
• Roll the appliance(s) into posion near the kitchen
enclosure, allowing enough space to work behind the
appliance(s) for connecng the ulies and in the case
of mulple appliances, the joining kit.
Step 3 — Hook Up Electrical and Water
• Unwind the power cord and connect it directly to the
wall socket.
• Make sure the appliance is in the stand-by condion
and that all lights are o; if necessary, press the Power
buon to switch it o.
• For Freezer Models: Connect the household water line
to the 1/4” quick connector elbow adapter supplied
with the product.
• Thread the elbow adapter onto the water valve on the
back of the appliance. Firmly ghten with ngers. A
tool should not be needed to make a proper seal. Turn
on the water and ensure all connecons are not leaking
prior to pushing the appliance into the enclosure.
Step 4 — Level the Appliance
• Adjust the height of the rear wheels by turning the
front adjusng bolts (1) clockwise (raise) or counter-
clockwise as required.
Important: Take care if using a power driver for the rear
leveling wheels. Reduce the torque seng to prevent
damage to the leveling mechanism.
Important: Do not make large adjustments to just one foot
or wheel by itself as the appliance will become unstable.
Make small adjustments to each foot and wheel locaon as
you go.
Step 5 — Aach Plasc Connecng Brackets
• Using the screws already installed in the sides of the
appliance, aach the plasc connecng brackets (A) to
the sides of the appliance.
1
1

12 [phone]
If not installing appliances side-by-side, please skip to Step 7
on page 13.
Step 6 — Side-by-side Installaon of Two
Appliances
Important: There is no need for a heater kit between the
appliances.
Important: The appliances must be level with one another to
allow the joining brackets to line up.
• Aach the joining brackets to the back of the appliance
that are included with the freezer column using the
appropriate screws and washers that are also included.
Installaon Instrucons
• Next join them at the front connecng each pair of
plasc brackets (A) with the supplied rivets using a rivet
tool. If a rivet tool is not readily available, an alternate
method is to use a #4x.312 long (M3x8mm) bolt and
nut to be supplied by the customer.
• Complete the installaon of the center joining kit by
aaching the central prole cover (C) that is included
with the freezer column onto the plasc brackets by
pushing it unl a “click” is heard.
WARNING
Appliances will be front-heavy and may p before they are
secured to the adjacent enclosure wall.
AVERTISSEMENT
Les appareils seront lourds à l'avant et peuvent basculer
avant d'être xés à la paroi adjacente de l'enceinte.

bluestarcooking.com 13
Step 7 — Install An-Tipping Safety Brackets or
Rear Wall Blocking
Important: If the top of the appliance is not accessible aer it
is installed due to the design of the cabinetry/enclosure, install
the wood blocking now. If the top of the appliance is
accessible, install the an-p brackets provided with the
appliance as described in Step 11.
Rear Wall Blocking
Place the block about 1/8-1/4" [3-6mm] above the nal height
of the rear of the appliance. For an 84” installaon opening,
this would be 81-3/8 to 81-1/2” from the oor. Blocking
should be a minimum thickness of 3” (76 mm) from the back
wall. Aach with appropriate fasteners into the wall studs.
Drywall anchors / toggle bolts are not recommended and can
rip out of the wall.
When the appliance is moved into its nal posion and the legs
adjusted, the top of the appliance can make contact with the
boom of the wood block, thus securing the appliance from
pping.
Installaon Instrucons
WARNING
To avoid danger of the appliance pping over it is mandatory
to secure the appliance to the wall by means of the two
provided brackets, or if the brackets are not accessible, by
means of a wood block at the rear wall of the enclosure.
AVERTISSEMENT
Pour éviter tout risque de basculement de l'appareil, il est
obligatoire de xer l'appareil au mur au moyen des deux
supports fournis, ou si les supports ne sont pas accessibles,
au moyen d'un bloc de bois sur la paroi arrière de l'enceinte.
Step 8 — Install Shoulder Bolts and Set Screws
(Panel-Ready Models)
• Prepare the appliance door for panel mounng by
threading the shoulder bolts into the recessed threaded
hole and the set screws into the other hole as shown
below. Ensure the end with the hex key socket is
accessible from the inside of the door and not from the
outside. Thread the set screws in far enough that they
are ush with foam surface on the appliance door
exterior face so as not to interfere with hanging the
panel. You will adjust these later from the inside of the
door.

14 [phone]
Installaon Instrucons
Step 9 — Install Panel (Panel-Ready Models)
• Align the top center bracket on the panel with the
recessed pocket in the door (6). Hook the panel brackets
onto the shoulder bolts (7).
• Install the included screw and washer into the threaded
hole on the top center bracket. This screw will be used
later to adjust the vercal locaon of the panel aer the
appliance is installed into the kitchen opening.
6
7
Step 10 — Move Appliance(s) Into Posion
• Roll the product into the cabinet opening, ensuring the
water line and the power cord do not interfere.
WARNING
Appliance will be front-heavy and may p before it is secured
to the adjacent enclosure wall.
AVERTISSEMENT
L'appareil sera lourd à l'avant et peut basculer avant d'être
xé à la paroi adjacente de l'enceinte.
• Check the level of the appliance(s) and t to surrounding
cabinetry. If the kitchen enclosure is 84” (2134 mm) tall,
the appliance(s) will need to be raised signicantly. Us-
ing a 11/16” (17 mm) wrench for the front leveling feet
and a 1/2” (13 mm) socket for the rear leveling wheels,
raise the appliance(s) to t the opening.
Important: Do not make large adjustments to just one foot
or wheel by itself as the appliance will become unstable.
Make small adjustments to each foot and wheel locaon as
you go. This is especially true on side-by-side installaons
where the appliances need to stay level to one another.
Step 11 — Install An-Tip Brackets
• When using the provided an-p brackets, they should
be applied as illustrated using the provided screws and
wall anchors.
• Find the mounng holes on top of the appliance, and
determine how the bracket must align with the wall.

bluestarcooking.com 15
• Mark the wall where the holes are needed.
• For a concrete block wall or 3/4” plywood wall, drill the
wall with a 5/16” [8 mm] bit and insert the wall anchor.
For a stud wall, drill a 1/8” (3 mm) pilot hole.
Installaon Instrucons
• Reposion the bracket and secure it rst to the
appliance, then to the wall.
In addion, it is required:
• The plasc connecng brackets must be screwed to the
cabinets at all provided aachment points as described
on page 16, Step 13.
• When two appliances are installed together, the an-
p brackets are required for each of them.
• The cabinet enclosure must be securely aached to the
wall to assure the stability of the appliance.

16 [phone]
Step 12 — Adjust Panel (Panel-Ready Models)
• The panel can be adjusted side-to-side at this point to
obtain consistent gaps.
• To adjust the vercal posion of the panel aer the
appliance(s) are installed into the kitchen opening,
ghten or loosen the screw in the top center bracket
using the supplied hex key to raise or lower the panel (8).
• Adjust the panel depth relave to the face of the
cabinetry. Working from inside the door, li the
magnec seal from the handle side of the door (9) and
rotate the plasc covers on the hinge side of the door
(10) to expose the holes that contain the shoulder bolts
and set screws. Using the included hex key, adjust the
panel posion in the Z-direcon by adjusng the
shoulder bolts.
• If the gaps around the panel become inconsistent during
the panel depth adjustment, loosen the shoulder bolts
and set screws to allow the panel to be adjusted side-to-
side.
• Lock the panel locaon in place by ghtening the set
screws against the back side of the panel.
• Once the panel is aligned, reinstall the magnec seal and
conrm the door is closing correctly to avoid operaonal
issues.
Installaon Instrucons
9
10
8
Step 13 — Aach Appliance(s) to Surrounding
Cabinetry
• Aer leveling the appliance(s) and checking t of the
panel(s) or door(s) to surrounding cabinetry, secure the
appliance to the adjacent cabinets by driving screws
through the plasc connecng brackets. Screws should
be provided by the customer. Keep the door open to
ease access to the screws.
• Aach the plasc proles (B) to the plasc connecng
brackets (A). First insert them laterally and then push
rmly unl a “click” is heard.
Single appliance installaon
Side-by-side appliance installaon

bluestarcooking.com 17
Step 15 — Aach Venng Grille
A forced air system assures venlaon through a grille
posioned in the lower front part of the appliance. Each
BlueStar Column comes with a 8-1/2” (216 mm) tall stainless
steel grille.
Important: If using a custom grille, it has to be venlated
with holes. Holes can be in any shape and size, as long as the
total area equals 50% of the area dened by dimensions “A”
and “B” below.
It is imperave that the grille remain unblocked to ensure
proper funconality of the appliance and should be
removable to allow for servicing and condenser cleaning.
Installaon Instrucons
18” 24” 30”
A16-1/8” (410
mm)
22” (559
mm)
27-15/16” (710
mm)
B> 4” (100 mm)
C3/8” (10 mm)
Step 14 — Aach Door Handle
A BlueStar handle is provided with stainless door models,
but must be ordered separately for panel-ready models.
• The handle and nameplate kit is located in protecve
packaging taped to the back of the appliance.
• It is recommended that two people work together to
install the handle.
• Ensure handle mounng studs are threaded nger-
ght to the face of the door.
• Slide handle endcaps onto the handle mounng studs.
If the set screw interferes, back out set screw to allow
endcaps to slip over handle mounng studs.
• Posion handle to face of door and with provided hex
wrench ghten set screw in top endcap rst, then
ghten set screw in boom endcap.

18 [phone]
Final Checklist
• Check that the connecon to the water system does not
have any leaks and that the valve is easily accessible.
• Check that the electrical connecon is correctly installed
and that the circuit breaker is idened/marked for later
use.
• Check that the appliance is level and aligns with adjacent
cabinets.
• Check that the an-p brackets are secure, and the side
connectors are secure with trim in place.
• Check that all adhesive tape and external or internal
temporary protecve packaging have been removed.
• Check the perfect closing of the doors and the smooth
sliding of the drawers and shelves.
• If the appliance has an ice maker, make sure the water
lter cartridge is installed. (Unless ltered water is being
provided to the appliance.) The water lter is located
behind a magnecally aached cover on top of the
freezer. Follow instrucons provided with the water
lter cartridge to install the lter.
Tesng and Inial Startup
Inial Startup
Once the appliance is plugged in, the display will show the
BlueStar logo, a brief info screen, then go dark.
Turn the appliance ON by pressing the Power buon for
three seconds. The display will show a BlueStar logo, then
the message “Inial test, please wait...” for 2-3 minutes.
Aer this phase the compressor will start up and remain on
unl the default temperature (set at the factory) is
reached. Allow ample me for the refrigerator to reach this
temperature before loading any items (6-12 hrs). During
this me, deacvate any error messages by pressing the
Alarm buon.
Ice Maker (Freezer Models only)
Make sure that the water lter cartridge is properly
installed, and the appliance is connected to the water
source. Purge air from the water lines by performing the
‘Manual Clean’ funcon from the Menu->Funcons->Water
Filter opons. You may need to complete this sequence
several mes unl you stop hearing air spuering from the
ice maker ll tube (Refer to your Use & Care Manual). Place
a small tray or bowl inside the ice bin, under the ice maker
tray to catch any water during the purge cycle. Once the
system is purged of air, switch the ice maker on by
touching the ice maker buon which will illuminate.
If the appliance has previously started the cooling process
prior to the rst start-up, it is normal for the Stand-By
message to not appear and for other messages to appear,
such as Fridge too warm, Freezer too warm, or audible
alarm sounds. If this is the case, deacvate acousc signals
by pressing the Alarm buon, close the door and wait unl
the set temperature is reached.
For further informaon about the appliance operaon,
refer to the User Manual.

bluestarcooking.com 19

20 [phone]