Blue-white Chem-feed cfws series User manual

Municipal Skid Systems

Series CFWS

CHEM-FEED

1.0

Introduction

2.0

Features

3.0

Specifications

4.0

Dimensions

5.0

Mounting a pump to the system

6.0

Mounting the skid system to wall

7.0

Component Identification and Typical Operation - Simplex Skid

7.1 How to Operate the Chem-Feed Skid System - Simplex Skid

8.0

Component Identification and Typical Operation - Duplex Skid

8.1 How to operate the Chem-Feed Skid System - Duplex Skid

9.0

Chem-Feed Skid System Matrix

10.0

Warranty

Page 2 Page 3

CHEM-FEED CFWS

READ THE INSTRUCTION MANUAL PRIOR TO INSTALLATION AND USE.

+1 (714) 893 - 8529

[email protected]

5300 Business Drive

Huntington Beach, CA 92649

1.0

Introduction

2.0

Features

3.0

Specifications

4.0

Dimensions

5.0

Mounting a pump to the system

6.0

Mounting the skid system to wall

7.0

Component Identification and Typical Operation - Simplex Skid

7.1 How to Operate the Chem-Feed Skid System - Simplex Skid

8.0

Component Identification and Typical Operation - Duplex Skid

8.1 How to operate the Chem-Feed Skid System - Duplex Skid

9.0

Chem-Feed Skid System Matrix

10.0

Warranty

Page 2 Page 3

CHEM-FEED CFWS

READ THE INSTRUCTION MANUAL PRIOR TO INSTALLATION AND USE.

+1 (714) 893 - 8529

[email protected]

5300 Business Drive

Huntington Beach, CA 92649

1.0 Introduction

Congratulations on purchasing the Chem-Feed® Engineered Wall Skid System. The system is designed with the

necessary components to safely inject liquid chemical into a system.

Your Chem-Feed® Engineered Wall Skid System is pre-configured based on your selections via the matrix or

when designed with our engineering staff.

Please Note: Your new Chem-Feed® System has been pressure tested at the factory with clean water for a

minimum of four hours before shipping. You may notice trace amounts of clean water in the system. This is part of

our stringent quality assurance program at Blue-White Industries.

2.0 Features

Chem-Feed® Engineered Skid Systems were designed and engineered using solid modeling tools for superior piping

installation and easy component maintenance. Custom engineered universal mounting blocks and pre-machined

mounting slots provide for easy component servicing and replacement. Each factory built and tested system includes

the following standard components:

!Pressure Relief Valve - Protects the system from over-pressurization, 5-150 psi setting range, 150 psi maximum system

pressure. Ships on all systems.

!Check Valve - Protects the user from back-flow during pump maintenance. Ships on all systems.

!Flow Verification Sensor - MS6 accurately verifies chemical feed. Exclusive to Blue-White®.

!Inlet Y Strainer - Protects system components from damage cause by dirt or debris.

!Calibration Cylinder - Confirm pump output under system conditions. Specify cylinder volumes from 3 GPH to 128

GPH.

!Pulsation Dampener - Protect the system components from pulsation. Recommended for diaphragm pump systems.

Not recommended for peristaltic pump systems.

!Pressure Gauge with Guard - Isolate and protect the system pressure gauge. Specify pressure ranges from 0-30 psi,

0-100 psi, or 0-200 psi.

!Strut Mounts - FRP Strut is provided with the skid to ensure sturdy support for wall mounting.

!Corrosion Resistant - Chem-Feed® frame constructed of chemically resistant polyethylene.

!Pump Mount Bracket - Constructed of chemically resistant polyethylene.

Page 4 Page 5

CHEM-FEED CFWS

3.0 Specifications

Items listed below are standard available items and ship with most configurations. Your system may be custom-

ized with components not listed below.

1.0 Introduction

Congratulations on purchasing the Chem-Feed® Engineered Wall Skid System. The system is designed with the

necessary components to safely inject liquid chemical into a system.

Your Chem-Feed® Engineered Wall Skid System is pre-configured based on your selections via the matrix or

when designed with our engineering staff.

Please Note: Your new Chem-Feed® System has been pressure tested at the factory with clean water for a

minimum of four hours before shipping. You may notice trace amounts of clean water in the system. This is part of

our stringent quality assurance program at Blue-White Industries.

2.0 Features

Chem-Feed® Engineered Skid Systems were designed and engineered using solid modeling tools for superior piping

installation and easy component maintenance. Custom engineered universal mounting blocks and pre-machined

mounting slots provide for easy component servicing and replacement. Each factory built and tested system includes

the following standard components:

!Pressure Relief Valve - Protects the system from over-pressurization, 5-150 psi setting range, 150 psi maximum system

pressure. Ships on all systems.

!Check Valve - Protects the user from back-flow during pump maintenance. Ships on all systems.

!Flow Verification Sensor - MS6 accurately verifies chemical feed. Exclusive to Blue-White®.

!Inlet Y Strainer - Protects system components from damage cause by dirt or debris.

!Calibration Cylinder - Confirm pump output under system conditions. Specify cylinder volumes from 3 GPH to 128

GPH.

!Pulsation Dampener - Protect the system components from pulsation. Recommended for diaphragm pump systems.

Not recommended for peristaltic pump systems.

!Pressure Gauge with Guard - Isolate and protect the system pressure gauge. Specify pressure ranges from 0-30 psi,

0-100 psi, or 0-200 psi.

!Strut Mounts - FRP Strut is provided with the skid to ensure sturdy support for wall mounting.

!Corrosion Resistant - Chem-Feed® frame constructed of chemically resistant polyethylene.

!Pump Mount Bracket - Constructed of chemically resistant polyethylene.

Page 4 Page 5

CHEM-FEED CFWS

3.0 Specifications

Items listed below are standard available items and ship with most configurations. Your system may be custom-

ized with components not listed below.

Simplex Pump System:

4.0 Dimensions

Your Chem-Feed System may be designed differently from drawings below. However, the dimensions shown

below remain the same no matter your configuration.

Duplex Pump System:

Page 6 Page 7

CHEM-FEED CFWS

C D

Simplex Pump System:

4.0 Dimensions

Your Chem-Feed System may be designed differently from drawings below. However, the dimensions shown

below remain the same no matter your configuration.

Duplex Pump System:

Page 6 Page 7

CHEM-FEED CFWS

C D

5.0 Mounting Pump to the Chem-Feed® System

Page 8

CHEM-FEED CFWS

Socket Head

Screw, SS #10-32 - .625”

#10 washer, and 10-32 nut.

(Qty: 4 of each per pump)

6.0 Mounting the Chem-Feed® System

1. Locate mounting position of skid on wall.

2. Use dimensions and strut to mark best location for wall anchors.

3. Remove strut from skid, and mount to wall with anchors.

4. Re-mount skid to strut.

5. Mount pump(s).

Mounting Bracket

(Qty: 2 per pump)

7.0 Component Identification and Typical Operation - Simplex Pump Skid

* PRV = Pressure Relief Valve preset at 50psi

Chemical

Output

Pressure Gauge

Chemical Feed

Flowmeter

(optional)

One way

Check Valve

(with union)

Calibration

Cylinder

Pulse

Dampener

(optional)

Chemical

Input

Y Strainer

PRV*

Gauge

Guard

Page 9 ®

CHEM-FEED CFWS

Pressure Switch

(optional)

Back Pressure Valve

(optional)

5.0 Mounting Pump to the Chem-Feed® System

Page 8

CHEM-FEED CFWS

Socket Head

Screw, SS #10-32 - .625”

#10 washer, and 10-32 nut.

(Qty: 4 of each per pump)

6.0 Mounting the Chem-Feed® System

1. Locate mounting position of skid on wall.

2. Use dimensions and strut to mark best location for wall anchors.

3. Remove strut from skid, and mount to wall with anchors.

4. Re-mount skid to strut.

5. Mount pump(s).

Mounting Bracket

(Qty: 2 per pump)

7.0 Component Identification and Typical Operation - Simplex Pump Skid

* PRV = Pressure Relief Valve preset at 50psi

Chemical

Output

Pressure Gauge

Chemical Feed

Flowmeter

(optional)

One way

Check Valve

(with union)

Calibration

Cylinder

Pulse

Dampener

(optional)

Chemical

Input

Y Strainer

PRV*

Gauge

Guard

Page 9 ®

CHEM-FEED CFWS

Pressure Switch

(optional)

Back Pressure Valve

(optional)

7.1 How To Operate the Chem-Feed® Skid System - Simplex Pump Skid

Connections:

Connect chemical solution into chemical Inlet (V-1)

Connect chemical treated system to outlet. (V-8)

To Pump chemical solution into system.

Open ball valve V-1.

Open ball valve V-3, V-4, and V-5 (if optional equipment included).

Close ball valve V-2, V-6, and V-7.

Open ball valve V-8 to inject chemical solution into your system.

Start pump.

To calibrate pump / system.

Open ball valve V-1.

Open ball valve V-7.

Close ball valve V-2, V-6, and V-8.

Start pump and run until calibration cylinder is filled to top calibration line. Do not leave pump unattended during

this operation.

Stop pump once calibration cylinder is filled.

Close ball valves V-1 and V-7.

Open ball valve V-2 and V-8 to inject chemical solution into your system.

Note the chemical solution level in the calibration cylinder.

To calibrate pump at maximum speed into your system, Press the prime button on pump. The prime mode runs the

pump at maximum speed for 60 seconds (1 minute) on all Blue-White® pumps.

To calibrate pump at your desired feed rate, you must pre-program your pump speed before running this routine.

Please refer to the instruction manual for your pump to adjust feed rate and additional calibration instructions.

Repeat process to ensure accuracy of calibration.

Page 10

CHEM-FEED CFWS

V-1

U-1 PRV-1

BPV-1

CV-1 PSH-1

PD-1

S-2

Ms6

G-1

S-1

U-5

U-6

U-4

U-3

V-2

CC-1

Chemical Outlet

Chemical Inlet

V-3 V-4

V-6

V-8

V-5

V-7

U-2

8.0 Component Identification and Typical Operation - Duplex Pump Skid System

One way

Check Valves

(with union)

PRV*

* PRV = Pressure Relief Valve preset at 50psi

Chemical

Output

Chemical

Input

Chemical Feed

Flowmeter

Calibration

Cylinder

Pressure

Gauge

Pulsation

Dampener

(optional)

Y Strainer

Page 11 ®

CHEM-FEED CFWS

V12

V5V6

V11

V10V9V8V7

V13

7.1 How To Operate the Chem-Feed® Skid System - Simplex Pump Skid

Connections:

Connect chemical solution into chemical Inlet (V-1)

Connect chemical treated system to outlet. (V-8)

To Pump chemical solution into system.

Open ball valve V-1.

Open ball valve V-3, V-4, and V-5 (if optional equipment included).

Close ball valve V-2, V-6, and V-7.

Open ball valve V-8 to inject chemical solution into your system.

Start pump.

To calibrate pump / system.

Open ball valve V-1.

Open ball valve V-7.

Close ball valve V-2, V-6, and V-8.

Start pump and run until calibration cylinder is filled to top calibration line. Do not leave pump unattended during

this operation.

Stop pump once calibration cylinder is filled.

Close ball valves V-1 and V-7.

Open ball valve V-2 and V-8 to inject chemical solution into your system.

Note the chemical solution level in the calibration cylinder.

To calibrate pump at maximum speed into your system, Press the prime button on pump. The prime mode runs the

pump at maximum speed for 60 seconds (1 minute) on all Blue-White® pumps.

To calibrate pump at your desired feed rate, you must pre-program your pump speed before running this routine.

Please refer to the instruction manual for your pump to adjust feed rate and additional calibration instructions.

Repeat process to ensure accuracy of calibration.

Page 10

CHEM-FEED CFWS

V-1

U-1 PRV-1

BPV-1

CV-1 PSH-1

PD-1

S-2

Ms6

G-1

S-1

U-5

U-6

U-4

U-3

V-2

CC-1

Chemical Outlet

Chemical Inlet

V-3 V-4

V-6

V-8

V-5

V-7

U-2

8.0 Component Identification and Typical Operation - Duplex Pump Skid System

One way

Check Valves

(with union)

PRV*

* PRV = Pressure Relief Valve preset at 50psi

Chemical

Output

Chemical

Input

Chemical Feed

Flowmeter

Calibration

Cylinder

Pressure

Gauge

Pulsation

Dampener

(optional)

Y Strainer

Page 11 ®

CHEM-FEED CFWS

V12

V5V6

V11

V10V9V8V7

V13

Connections:

Connect chemical solution into Inlet. (V-1)

Connect chemical treated system to outlet. (V-13)

To Pump chemical solution into system.

Open ball valve V-1.

Open ball valve V-3, or V-4, depending on which pump is being used.

Close ball valve V-2, V-11, and V-12.

Open ball valve V-5 or V-6, depending on your system design.

Open ball valve V-7, V-8, V-9, V-10 depending on your system design.

Open ball valve V-13 to inject chemical solution into your system.

Start pump(s).

To calibrate pump(s) / system.

Open ball valve V-1.

Open ball valve V-3 or V-4, depending on which pump is being calibrated.

Open ball valve V-5 or V-6, depending on which pump is being calibrated.

Close ball valve V-2, V-11, and V-13.

Open ball valve V-12. This open valve will direct chemical into calibration cylinder.

Start pump and run until calibration cylinder is filled to top calibration line. Do not leave pump unattended during

this operation!

Stop pump once calibration cylinder is filled.

Close ball valves V-1 and V-12.

Open ball valve V-2 and V-13 to inject chemical solution into your system.

Note the chemical solution level in the calibration cylinder.

To calibrate pump at maximum speed into your system, Press the prime button on pump. The prime mode runs the

pump at maximum speed for 60 seconds (1 minute) on all Blue-White pumps.

To calibrate pump at your desired feed rate, you must pre-program your pump speed before running this routine.

Please refer to the instruction manual for your pump to adjust feed rate and additional calibration instructions.

Repeat process to ensure accuracy of calibration.

8.1 How To Operate the Chem-Feed® Duplex Skid System

Page 12

CHEM-FEED CFWS

V-2

Chemical Inlet

Chemical Outlet

U-1

S-1

Ms6

BPV-1

PD-2

PSH-1

G-1

PD-1

PRV-1

PRV-2

S-2

U-2

U-6

U-3 U-4 CV-1

CV-2

U-5

U-8

U-7

U-9

CC-1

V-3

V-4

V-5

V-11

V-7 V-8 V-9 V-10

V-13

V-12

V-6

V-1

CHEM-FEED® Simplex Wall Skid System - Municipal

CFWS-1 Single pump system - single chemical / single outlet, PE structure

Inlet/Outlet

ASingle Inlet / Single Outlet

XNone, Skid Panel Only

Piping/Unions

APVC CPVDF

BCPVC DCHEM PROLINE®

Seals

VFKM EEPDM

Tubing Connections

A1/2” ID PVC Braided C1/4” ID PE

B 1/2” ID PTFE D1/4” ID PTFE

Calibration Column

A128 GPH (4000 ml) PVC F3 GPH (100 ml) PVC

B64 GPH (2000 ml) PVC P32GPH (1000 ml) Glass

C32 GPH (1000 ml) PVC Q16 GPH (500 ml) Glass

D16 GPH (500 ml) PVC R8 GPH (250 ml) Glass

E8 GPH (250 ml) PVC S3 GPH (100 ml) Glass

Pulsation Dampener

P10 cubic in XNot Included

Back Pressure Valve

BIncluded XNot Included

Pressure Gauge w/Guard

A200 PSI B100 PSI C30 PSI

Pressure Switch w/Guard

SIncluded XNot Included

Flow Meter w/Strainer

A10-5000 mL/min

B100-10000 mL/min

XNot Included

CFWS-1 M A A V A A P B A S A X X Sample Model Number

Model Number Matrix CFWS-1-M

NOTES: When ordering pumps for skids, pump head orientation is standard LEFT facing only. Terminal Boxes quoted and mounted separatel y.

All skids are pressure tested prior to shipment. Pumps are puchased and shipped separately.

Page 13 ®

CHEM-FEED CFWS

9.0 Chem-Feed Skid System Matrix

Connections:

Connect chemical solution into Inlet. (V-1)

Connect chemical treated system to outlet. (V-13)

To Pump chemical solution into system.

Open ball valve V-1.

Open ball valve V-3, or V-4, depending on which pump is being used.

Close ball valve V-2, V-11, and V-12.

Open ball valve V-5 or V-6, depending on your system design.

Open ball valve V-7, V-8, V-9, V-10 depending on your system design.

Open ball valve V-13 to inject chemical solution into your system.

Start pump(s).

To calibrate pump(s) / system.

Open ball valve V-1.

Open ball valve V-3 or V-4, depending on which pump is being calibrated.

Open ball valve V-5 or V-6, depending on which pump is being calibrated.

Close ball valve V-2, V-11, and V-13.

Open ball valve V-12. This open valve will direct chemical into calibration cylinder.

Start pump and run until calibration cylinder is filled to top calibration line. Do not leave pump unattended during

this operation!

Stop pump once calibration cylinder is filled.

Close ball valves V-1 and V-12.

Open ball valve V-2 and V-13 to inject chemical solution into your system.

Note the chemical solution level in the calibration cylinder.

To calibrate pump at maximum speed into your system, Press the prime button on pump. The prime mode runs the

pump at maximum speed for 60 seconds (1 minute) on all Blue-White pumps.

To calibrate pump at your desired feed rate, you must pre-program your pump speed before running this routine.

Please refer to the instruction manual for your pump to adjust feed rate and additional calibration instructions.

Repeat process to ensure accuracy of calibration.

8.1 How To Operate the Chem-Feed® Duplex Skid System

Page 12

CHEM-FEED CFWS

V-2

Chemical Inlet

Chemical Outlet

U-1

S-1

Ms6

BPV-1

PD-2

PSH-1

G-1

PD-1

PRV-1

PRV-2

S-2

U-2

U-6

U-3 U-4 CV-1

CV-2

U-5

U-8

U-7

U-9

CC-1

V-3

V-4

V-5

V-11

V-7 V-8 V-9 V-10

V-13

V-12

V-6

V-1

CHEM-FEED® Simplex Wall Skid System - Municipal

CFWS-1 Single pump system - single chemical / single outlet, PE structure

Inlet/Outlet

ASingle Inlet / Single Outlet

XNone, Skid Panel Only

Piping/Unions

APVC CPVDF

BCPVC DCHEM PROLINE®

Seals

VFKM EEPDM

Tubing Connections

A1/2” ID PVC Braided C1/4” ID PE

B 1/2” ID PTFE D1/4” ID PTFE

Calibration Column

A128 GPH (4000 ml) PVC F3 GPH (100 ml) PVC

B64 GPH (2000 ml) PVC P32GPH (1000 ml) Glass

C32 GPH (1000 ml) PVC Q16 GPH (500 ml) Glass

D16 GPH (500 ml) PVC R8 GPH (250 ml) Glass

E8 GPH (250 ml) PVC S3 GPH (100 ml) Glass

Pulsation Dampener

P10 cubic in XNot Included

Back Pressure Valve

BIncluded XNot Included

Pressure Gauge w/Guard

A200 PSI B100 PSI C30 PSI

Pressure Switch w/Guard

SIncluded XNot Included

Flow Meter w/Strainer

A10-5000 mL/min

B100-10000 mL/min

XNot Included

CFWS-1 M A A V A A P B A S A X X Sample Model Number

Model Number Matrix CFWS-1-M

NOTES: When ordering pumps for skids, pump head orientation is standard LEFT facing only. Terminal Boxes quoted and mounted separatel y.

All skids are pressure tested prior to shipment. Pumps are puchased and shipped separately.

Page 13 ®

CHEM-FEED CFWS

9.0 Chem-Feed Skid System Matrix

Page 15

CHEM-FEED CFWS

10.0 WARRANTY

10.1 Limited Warranty

The skid is a quality product and is warranted for 24 months from date of purchase (proof of purchase is required). The

skid will be repaired or replaced at our discretion. The pump(s) have a separate warranty and are not covered under this

warranty.

10.2 What is not Covered

> The pump(s) included with skid have a separate warranty. Refer to pump warranty page for informa-

tion.

> Removal, or re-installation, and any related labor charge.

> Freight to the factory.

> Skids that have been tampered with, or in pieces.

> Damage to the skid that results from misuse, carelessness, abuse, lack of maintenance, or alteration

that is out of Blue-White's control.

> Skids damaged by or acts of nature.

Blue-White does not assume responsibility for any loss, damage, or expense directly or indirectly related to or arising out

of the use of its products. Failure must have occurred due to defect in material or workmanship and not as a result of

operation of the product other than in normal operation as defined in the pump operation manual.

The warranty status is determined by the skid's serial label and the sales invoice or receipt. The serial label must be on

the skid and be legible. The warranty status of the skid will be verified by Blue-White or a factory authorized service

center.

10.3 Obtaining In-Warranty Repair

Contact the factory to obtain a RMA (Return Material Authorization) number. Carefully pack the sytem as instructed.

Please enclose a brief description of the problem as well as the original invoice or sales receipt, or copy showing the date

of purchase. Prepay all shipping costs. COD shipments will not be accepted. Warranty service must be performed by the

factory or an authorized service center. Damage caused by improper packaging is the responsibility of the sender. When

In-Warranty repair or replacement is completed, the factory pays for return shipping to the dealer or customer.

10.4 Product Use Warning

Blue-White products are manufactured to meet the highest quality standards in the industry. Each product instruction

manual includes a description of the associated product warranty and provides the user with important safety information.

Purchasers, installers, and operators of Blue-White products should take the time to inform themselves about the safe

operation of these products. In addition, Customers are expected to do their own due diligence regarding which products

and materials are best suited for their intended applications. Blue-White is pleased to assist in this effort but does not

guarantee the suitability of any particular product for any specific application as Blue-White does not have the same

degree of familiarity with the application that the customer/end user has. While Blue-White will honor all of its product

warranties according to their terms and conditions, Blue-White shall only be obligated to repair or replace its defective

parts or products in accordance with the associated product warranties. BLUE-WHITE SHALL NOT BE LIABLE EITHER

IN TORT OR IN CONTRACT FOR ANY LOSS OR DAMAGE WHETHER DIRECT, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL, ARISING OUT OF OR RELATED TO THE FAILURE OF ANY OF ITS PARTS OR PRODUCTS OR

OF THEIR NONSUITABILITY FOR A GIVEN PURPOSE OR APPLICATION.

10.5 Chemical Resistance Warning

Blue-White offers a wide variety of wetted parts. Purchasers, installers, and operators of Blue-White products must be well

informed and aware of the precautions to be taken when injecting or measuring various chemicals, especially those

considered to be irritants, contaminants or hazardous. Customers are expected to do their own due diligence regarding

which products and materials are best suited for their applications, particularly as it may relate to the potential effects of

certain chemicals on Blue-White products and the potential for adverse chemical interactions.

Blue-White tests its products with water only. The chemical resistance information included in this instruction manual was

supplied to Blue-White by reputable sources, but Blue-White is not able to vouch for the accuracy or completeness thereof.

While Blue-White will honor all of its product warranties according to their terms and conditions, Blue-White shall only be

obligated to repair or replace its defective parts or products in accordance with the associated product warranties.

BLUE-WHITE SHALL NOT BE LIABLE EITHER IN TORT OR IN CONTRACT FOR ANY LOSS OR DAMAGE, WHETHER

DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL, ARISING OUT OF OR RELATED TO THE USE OF

CHEMICALS IN CONNECTION WITH ANY BLUE-WHITE PRODUCTS.

CHEM-FEED® Duplex Wall Skid System Matrix - Municipal

CFWS-2 Duplex pump system - single chemical / single outlet, PE structure

Inlet/Outlet

ASingle Inlet / Single Outlet

XNone, Skid Panel Only

Piping/Unions

APVC CPVDF

BCPVC DCHEM PROLINE®

Seals

VFKM EEPDM

Tubing Connections

A1/2” ID PVC Braided C1/4” ID PE

B 1/2” ID PTFE D1/4” ID PTFE

Calibration Column

A128 GPH (4000 ml) PVC F3 GPH (100 ml) PVC

B64 GPH (2000 ml) PVC P32 GPH (1000 ml) Glass

C32 GPH (1000 ml) PVC Q16 GPH (500 ml) Glass

D16 GPH (500 ml) PVC R8 GPH (250 ml) Glass

E8 GPH (250 ml) PVC S3 GPH (100 ml) Glass

Pulsation Dampener

P10 cubic in XNot Included

Back Pressure Valve

BIncluded XNot Included

Pressure Gauge w/Guard

A200 PSI B100 PSI C30 PSI

Pressure Switch w/Guard

SIncluded XNot Included

Flow Meter w/Strainer

A10-5000 mL/min

B100-10000 mL/min

XNot Included

CFWS-2 M A A V A A P B A S A X X Sample Model Number

Model Number Matrix CFWS-2-M

NOTES: When ordering pumps for skids, pump head orientation is standard LEFT facing only. Terminal Boxes quoted and mounted separatel y.

All skids are pressure tested prior to shipment. Pumps are puchased and shipped separately.

CHEM-FEED CFWS

Page 14