Bluesky CT-179 User manual

Operating Manual
CT-179
Caller ID Phone

2
Features:
1. Works with FSK/DTMF systems
2. New Call, Repeat Call display
3. 40 memory for incoming call
4. 10 memory for outgoing call
5. Last number redial, flash, hold music
6. Call back from memory
7. 12 polyphonic melody and 4 ringing melody selection
8. Ring and hands free dialing volume adjustable
9. LCD contrast adjustable
10. Anti-fraud dialing
Legend:
1. DC SOCKET
2. LINE IN
3. LCD
4. SET
5. DOWN
6. DIAL CHECK
7. LCD CONTRAST
8. REDIAL
9. FLASH/RING
10. IN USE
11.HANDS FREE
12.KEYPAD
13.HOLD
14.RING INDICATER
15.PAUSE
16.CALL BACK
17.DELETE
18.VOLUME
19.HANDSET
20.UP

3
Installation:
You may provide power to the CT-179 with the use of AA
batteries.
To install batteries:
Turn the unit over. Remove the battery compartment cover. Insert
3 AA batteries following the polarity diagram. Replace the battery
compartment cover.
Choose the telephone outlet in your home or office where you
wish to connect the unit. Plug the supplied telephone line to the
telephone outlet. Connect the other end of the telephone line to
the unit.
Plug one end of the supplied coil cable into the outlet of handset.
Connect the other end to the unit.
battery
telephone line
NOTE: You should replace the new battery if the LCD can not be
adjusted to a suitable reading or the function key can’t work well.
If the unit is not properly featured, you need to remove battery and
telephone line then, re-connect 10 minutes later. To avoid shock,
unplug telephone line before replacing battery.

4
Setup:
1.Setup time and date:
Press SET key when the unit is in standby mode. The SET
1dATE will be displayed. Press SET key again. The LCD should
be flickering on 20XX,. Press Up or DOWN key to set year.
Press SET. Month should be flickering. Press UP or DOWN key
to set month. Press SET to move to date. Press UP or DOWN to
set date etc., Unit will respond with SET 2 CodE when date and
time are set. Press DELETE after finishing setting.
2. Setup area code:
The LCD will display SET 2 CodE after finishing the time and
date setting or press SET key then press UP key to enter SET 2
CodE mode when unit is in standby mode. Press SET again.
The LCD will display CodE 1. Press SET key, then press the UP
and DOWN keys to select the area code. Press SET key to
confirm the area code is set.
NOTE: The area code is associated with the place where the
unit is connected. For example: If the unit was used in Taipei,
you can set the area code 02 or 2 to be deleted while the unit
receive a local call and will recall from the call memory.
3.Setup long distance area code:
The setup is the same as you set up for local area code when
the unit is in SET 3 CodE.
4. Setup flash time:
The LCD will display SET4 FLASH after long distance area code
was set or Press SET key, then press UP key repeatedly until
the SET4 FLASH is displayed. Press SET key to observe
currently set flash time. Press UP or DOWN key to select. Press
SET key to confirm the selection. Press DELETE after finishing
setting.

5
The unit supplies with 90ms, 120ms, 180ms, 300ms, 600ms and
1000ms flash duration. Set the flash time to 600ms if you have
applied for call waiting service.
5. Anti-fraud dialing:
Press SET key, then press UP key repeatedly until the LCD
display SET 7 ALAr. Press SET key the LCD will display ALAr
OFF . Press UP or DOWN key to turn on/off the alarm function.
Press SET to confirm the setting. Press DELETE after finishing
setting. The unit will alarm while fraud dialing is detected.
6. Ringing volume:
In standby mode, press VOLUME key to select the ringing
volume.
7. Hands free dialing volume:
In standby mode, press HANDSFREE key. Press VOLUME key
repeatedly to select volume while hearing dialing tone. Press
HANDSFREE key again to confirm the setting.
8. LCD contrast control:
With the unit in standby mode, press LCD key to adjust the LCD
brightness. The unit provides 5 level of brightness.
9. Ringing melody selection:
Press the FLASH/RING key repeatedly to select the melody
while the unit is in standby mode. The unit provides12
polyphonic melodies and 4 ringing melodies. You also can
switch off the melody (The LCD will display RING OFF). rIng 01
to rIng 12 are for 12 polyphonic melodies. RIng A is for
automatic melody selection. rIng 14 to rIng 17 are for ringing
melodies.