USB INPUT (TYPE A) Connect a USB mass storage device to the USB input. Typical USB mass storage devices
compatible with the NODE include portable flash memory devices and external hard drives (FAT32 formatted).
LAN PORT The LAN PORT connection can be used with the Ethernet cable provided. This is an optional connection
since the POWERNODE can be connected to the network through a Wi-Fi connection to your router. To setup the
POWERNODE using the LAN Port a Wired Ethernet connection is required. Using the Ethernet cable provided, connect
one end of the Ethernet cable to the LAN port of your wired Ethernet broadband router and the other end to the
POWERNODE’s LAN port.
IR IN An infrared extender can be connected to allow for programmable learning remotes to control volume and source
selection when a POWERNODE is stored in a way that the front panel IR sensor is not visible.
OPTICAL IN/ANALOG IN 2 TUsing a 3.5mm Stereo Audio Cable (not provided), connect one end to the Analog In of the
POWERNODE and the other end to the corresponding analog output of other compatible devices. The source will show as
an Analog Input 2 in the BluOS App. Using the 3.5mm Mini Jack to Toslink adaptor (included with the POWERNODE), a
digital optical source can also be added. This will appear as Optical Input 2 in the BluOS App.
SPEAKERS Connect the right speaker to the terminals marked “R+” and “R-” ensuring that “R+” is connected to the “+”
terminal on your loudspeaker and “R-” is connected to the loudspeaker’s “-” terminal. Repeat for the left speaker using
“L+” and “L-“. Use extra care to ensure that no stray wires or strands cross between posts or terminals at either end.
HDMI eARC Using a HDMI cable (not provided), connect one end to the eARC input of the POWERNODE and the other
end to an ARC-enabled HDMI output on your television. You may be required to enable ARC in your TV settings. Consult
you TV user manual for more information. The source will appear as HDMI ARC in the BluOS App
AC MAINS INPUT The POWERNODE comes supplied with two separate AC power cords. Select the AC power cord
appropriate for your region. Before connecting the plug to the wall outlet, connect firmly the other end of the AC power
cord to POWERNODE’s AC Mains input socket. Never force the plug into a wall outlet. An adaptor may be necessary
in certain regions. Always disconnect the plug from the wall outlet first, before disconnecting the cable from the
POWERNODE’s AC Mains input socket.et.
STATUS INDICATOR Below is a table of the LED blink codes and their corresponding descriptions
4
9
11
12
13
14
10
LED BLINK CODE DESCRIPTION
Short blue flash, then red Powering up, rebooting the unit
Solid green Hotspot Mode
Flashing green Connecting to Network
White pulse Software update available
Solid red Upgrade Mode
Alternate flashing red and green Upgrading
Flashing blue Mute Mode
Solid white Indexing
Solid blue Connected to Network – ready to use with BluOS App
Flashing red Factory Reset in process
Solid purple Hotspot Mode timed out
4 5
PLAY/PAUSE BUTTON This button has multiple functions – a visual indicator of network connectivity and a PLAY/PAUSE
button. For a full listing of LED Blink Codes, please see #4 – Blink Codes. For an ungrouped Player, press the button to
Play and Pause the stream. If listening to an internet radio stream, the Pause- function will work for 30 seconds. At this
point, the buffer is full and the stream will Stop. When a Player is grouped, pressing the PLAY/PAUSE button will Mute
that Player while other Players continue the stream. The Player’s LED will flash blue when muted. This button is also
used for Factory Reset functions. See steps for Factory Reset later in this manual.
HEADPHONE JACK A 3.5mm headphone jack is located on the front of the POWERNODE.
OPTICAL/ANALOG IN 1 Using a 3.5mm Stereo Audio Cable (not provided), connect one end to the Analog In of the
POWERNODE and the other end to the corresponding analog output of other compatible devices. The source will show as
an Analog Input 1 in the BluOS App. Using the 3.5mm Mini Jack to Toslink adaptor (included with the POWERNODE), a
digital optical source can also be added. This will appear as Optical Input 1 in the BluOS App.
SUBW (SUBWOOFER) OUT A subwoofer can be connected directly to the POWERNODE. Connect SUBW OUT to a
powered (“active”) subwoofer. By default, a crossover is applied at 80Hz meaning audio below 80Hz is transmitted
through the SUBW OUT. Alternatively, you can connect the NODE to a Bluesound PULSE SUB+ over the network.
7
8
5
6
15
1PRESETS The POWERNODE has 5 programmable preset buttons. These presets are configured using the presets
menu in the BluOS App.
VOLUME SLIDER/TAP Use the LED slider to vary volume level. Tap the • buttons at either end of the slider to vary the
volume level in 1db intervals, or tap the slider in the direction you wish to adjust to vary the level by 3db intervals. These
volume tap methods allow you to fine-tune your volume setting.
PREVIOUS TRACK/NEXT TRACK These buttons can be used to go back to the previous track or skip to the next track in
your current play queue.
2
3
