BlueTrek Tattoo User manual

EC - Declaration of Conformity
We,Innovi Technologies Ltd of
31/F China Online Centre,
333 Lockhart Road,
WanChai, Hong Kong
declare under our sole responsibility that our product
BLUETREKTATTOO
to which this declaration refersis in conformity with the appropriate standards
EN300 328-02
EN301 489-17
EN301 489-01
EN50371
EN60950
Followingthe provisions of Radio and Telecommunications TerminalEquipment directive
1999/5/EC.
February 2007
Guillaume Ponticelli,Director of Development
FCC/Industr y CanadaNotice
This device complies with Part 15 of the FCCrules. Operation is subject to the following two
conditions:(1) This device may not cause harmful interference. (2)This device must accept
any interference received,including interference that may cause undesired operation.
In compliance with Industry Canada regulations,technical specifications have been
provided in a declaration of conformity.This does not imply that Industry Canada approved
the equipment.
Caution: Changes or modifications to this Bluetooth® headset not expresslyapproved by
the party responsible for compliance could void the user’sauthority to operate it.
Bluetooth® is a trademark owned by Bluetooth SIG,Inc. and is used by the manufacturer
under license.
Before using your headset for the first time
-Youmust charge it continuously for about 4 hours, until the red indicator light turns off.
Please refer to the“Charging the BLUETREK® TATTOO”section of this manual.
-Pair the headset with a mobile phone.Please refer to the “Pairingthe BLUETREK® TATTOO”
section of this manual.
Introduction
The BLUETREK®TATTOO headset is a wireless headset based on the Bluetooth® technology.It
complies with Bluetooth® 2.0 protocol,supporting Headset and Hands-free profile.
The BLUETREK®TATTOO headset has 2 buttons:
·“TALK” button (main button)
· 1“VOL+/- “ button
1 I BLUETREKTATTOO
Removable
earhook
TALKbutton
VOL+/- button
Microphone
Charging socket
Indicator light
Replaceable“skin”
English
Charging the BLUETREK®TATTOO
Please connect the charger to the headset and to the main.During the charge, the
indicator light is red. The indicator light will turn off when the charge is complete.During
subsequent charges,the charging should take approximately 3 hours.
When you hear a low-tone beep in yourheadset at regular inter vals,and the indicator light
flashes in red,your headset needs to be recharged.
Important:
· If your headset is fully charged,the red indicator light will not turn on when plugging
into the charger.
(To check whether your headset is fully charged,press the talk button for approx.
2 seconds,once released, the red indicator light will turn on for approx.3 seconds.)
·To maximize battery lifetime, it is recommended to recharge your headset tofull c apacity
only when the battery is low,since a battery has a lifetime of about 500 charging cycles.
· If you leave yourheadset batter y empty for an extended period of time,it could
excessivelydischarge the batter y.In this case, chargeyour headset for 3 hours or more
until the battery recovers and rechargescompletely. When you first charge the headset
after prolonged storage,it may take few minutes for the red indicator light to turn on.
· Do not charge your headset for more than 10 hours.
· The use of any other charger will automatically suspend the warranty. It is strictly
forbidden and can be very dangerous.
BLUETREKTATTOO I 2
English
Pairing the BLUETREK®TATTOO
Before using the BLUETREK®TATTOO headset,you must pair it with your Bluetooth® mobile
phone.Pairing is the process of linking 2 Bluetooth® devices, so that they can communicate.
Toinitiate pairing:
Place the BLUETREK®TATTOO and your mobile phone within 0.3 meter(1 foot) from each
other.
3 I BLUETREKTATTOO
English
Wearing the BLUETREK®TATTOO
Twodifferent sizes of ear hooks are included in the pack to suit your ear size.
The ear hook may be attached to the headset to improvestability.
Toattach the ear hook, simply insert the
ear hook ring to the back of the headset
as shown in the diagram.
For left ear wearing,the ear hook should
be inserted from the right hand side.
Switching the BLUETREK®TATTOO ON and OFF
Switching BLUETREK®TATTOOON
When your headset is off,press and hold the TALKbutton for about 3 seconds until the
green indicator light is on.A beep (2 tones) can be heard in the speaker. Release the
TALKbutton.
Switching BLUETREK®TATTOOOFF
When your headset is on,press and hold the TALK button for about 7 seconds until the red
indicator light is on.A beep (2 tones) can be heard in the speaker then release the TALK
button.
Making a call
Mobile phone with voicerecognition
.Make sure the voice recognition function on your mobile is activated and your voice tags
have been recordedwith the phone. To enter these,please refer to your phone’smanual
.When there is no incoming or active call, press once on theTALK button
.Wait for the audio signal sent by the mobile phone (generally a short tone).
.Speak the name of person you wish to call.
Mobile without voicerecognition
.Make sure both the headset and the mobile phone are ON and in stand-by mode.
. Dial the number on the phone keypad, after approximately 2 seconds the audio
connection will be established.
This function may not be available on some phones,please refer to the trouble shooting
frequent asked questions in our website:www.bluetrek.com. to find out more.
Answering a call
When the headset rings,press once on the TALK button to take the call.
Ending a call
Press once on theTALK button to end an active call.
Adjusting the volume
Toincrease the volume during an active call, press the“ VOL+”button on the headset.
Todecrease the volume during an active call, press the“ VOL-“ button on the headset.
Muting the microphone
Tomute the microphone during an active call
During an active call,press and hold the VOL+ button for approximately 2 seconds. A
periodic tone can be heard in the speaker when the microphone is muted.
Toend the mute function
When the microphone is muted,quickly press the VOL+ button on the BLUETREK® TATTOO.
The periodic tone will end.
Transferringa call from BLUETREK® TATTOOto the mobile phone
During an active call,press the TALK button for about 2 seconds.
This function only works in the Hands-Free Profile.
In the Headset profile,you can simply turn off your headset.
Transferringa call from the mobile phone to the BLUETREK® TATTOO
During an active call on the mobile phone,press once on the TALK button to transfer the call.
This function may not be available depending on yourphone.
Fitting the Ergobud*
Toreplace the Ergobud*,
remove the speaker coverby
pulling gently out from the
speaker.
Place the Ergobud* back onto the
speaker by inserting the bottom
part first.
3 different sizes of Ergobud*are included in the pack to suit your ear size. Youcan adjust
the Ergobud position that you feelthe most comfor table.
* Registered trademark pending
S M L
Replacing the“skin”
Toreplace the “skin”,simply peel off the sticker
from the edge of the sticker as shown in the diagram.
Stick the new“skin”back to the headset slowly along
the edge as shown in the diagram. Press the “skin”
to ensure it is firmly adhered.
Call waiting
When you hear a call waiting alert while you are on a call,press approx. 3 seconds
on theTALK button to accept the second call and place the current call on hold.
Toswitch between an active call and a hold call, press approx. 3 seconds on the
TALKbutton.
Toend the active call and take the hold call, press once on the TALKbutton.
This function may not be available,depending on your phone. However,you can always
answer the second call from your phone keypad.
Additional features with some phones
Rejecting a call
Press theTALK button for about 2 seconds to reject a call.
Redial the last number
When there is no incoming or active call,press the TALK button for about 3 seconds until
you hear a beep.
Troubleshooting guide
The first thing you should do when encountering a problemthat you cannot solve with this
manual,is to switch off your headset and your mobile phone, and switch them on again.
Tofind out more, please refer to the trouble shooting frequent asked questions in our
website:www.bluetrek.com.
Guidelines for safe use
Read those guidelines before using your headset.
- The volume level of the Bluetooth® headset may vary, depending on your mobile phone.
Before using your headset forthe first time, adjust the headset volume to the lowest, then
increase the volume gradually until youreach to an acceptable level.
High levels of volume mayresult in hearing loss, avoid using the headset at high volume
continuously. If you experience ringing in your ears or muffled speech, consult your doctor
immediately and stop using the headset.
- Do not drop or try to alter the shape of your headset.
- Do not expose your headset to liquid or moisture.
- Do not expose your headset to extreme temperatures.Temperature range :0-40C.
- Do not expose your headset to fire or open flames.
- Do not try to disassemble your headset.Ser viceand M aintenancecan only be per formed
by authorized BLUETREK®dealers.
- Keep your headset away fromdust and dir t.
- Do not let children play with your headset,since it contains small parts that could become
detached and create a choking hazard.
- Check the regulation in your area if youplan to use your headset while driving.
- Turn off your headset before boarding an airplane.
CAUTION :Danger of explosion if battery is incorrectly replaced. Dispose of batteries
according to local regulations.Do not dispose as household waste.
1
2
BLUETREK TATTOO
“0000”
4
BLUETREK TATTOO
3
BLUETREK TATTOO
5
BLUETREK TATTOO
Connect
Assign shortname
Set as unauthorised
Delete
Select Cancel
Switch on your phone and select its
Bluetooth® discover mode (referto the
Bluetooth® mobile phone user manual).
If pairing was successful,the indicator light will switch to green and flashes slowly.
If you haven’tstarted the discovery mode within 5 minutes, the headset will go to the
standby mode. You must then switch off your headset and start the pairing again.
When the BLUETREK® TATTOOis switched
off,press and hold the TALK button for
about 7 seconds until the indicator light
flashes red and green alternately. And a
sound can be heard in the speaker.
English
Once the mobile phone detects the headset,a “BLUETREKTATTOO”message
will be displayed.Follow the phone instructions to accept the pairing.The PIN
code (or passkey) is 0000,then press “yes”or “ok”.
For some phones,you
may need to select
“Connect”
BLUETREKTATTOO I 4
11 I BLUETREKTATTOO
English
5 I BLUETREKTATTOO
English
English
BLUETREKTATTOO I 6
7 I BLUETREKTATTOO
English
English
BLUETREKTATTOO I 8
9 I BLUETREKTATTOO
English
English
BLUETREKTATTOO I 10
English
BLUETREKTATTOO I 12
Noteon environmental protection:
Afterthe implementation of the European Directive 2002/96/EU in the national legal system, the following
applies:
Electrical and electronic devices may not be disposed of with domestic waste.
Consumersare obliged by law to return electrical and electronic devices at the end of their service lives to
the public collecting points set up forthis purpose or point of sale. Details to this are defined by the
nationallaw of the respective countr y.This symbol on the product,the instruction manual or the pack age
indicatesthat a product is subjec t to these regulations.By recycling, reusing the materials or other forms of
utilising old devices,you are making an important contribution to protecting our environment.
GB