Bogen ACD2X2 User manual

Self-Amplified Drop-In Ceiling Speaker
ACD2X2, ACD2X2U
with Back Can and Recessed Volume Control
CEILING GRID
CEILING GRID
SUPPORT RAIL
CROSSBAR INCLUDED
(2 ft. X 4 ft. CEILING GRID ONLY)
CEILING TILE
(CUT IN HALF, OR NO MORE
THAN 23-3⁄4")
ACD2X2
ACD2X2
2 ft. X 2 ft.
TILE SPACE
2 ft. X 4 ft.
TILE SPACE
Bogen’s ACD2X2 Drop-In Ceiling Speaker is a full-range
speaker that allows for fast and easy installation, which
saves installation time, effort, and cost.
The ACD2X2 is a 2' x 2' speaker that fits perfectly into
place in 2' x 2' ceiling grids – without needing to cut
ceiling tiles or requiring the use of tile support rails. The
ACD2X2 can also be easily installed in 2' x 4' ceiling grids
– just make one cut to the ceiling tile, position the support
rail (included), and drop the speaker into place.
•Finely perforated grille over the entire front of speaker
•Fully enclosed, industrial grade steel construction
•Enclosed Back Can
•Self-contained 1-watt amplifier
•8'' main cone with secondary high-frequency cone
•Available in off-white and bright white (“U” versions)
grille finish
•Recessed Volume Control (front-mounted)
•Complies with Requirements of UL-2043
•Support Rail Crossbar (included)

Frequency Response . . . . . . . . . . 95 Hz - 12 kHz
Max. SPL @ 1W / 1m . . . . . . . . . . 94 dB
Dispersion @ 2 kHz
(6 dB down) . . . . . . . . . . . . . . . . . .100°
Cone Material & Surround . . . . . . Treated paper
Cones . . . . . . . . . . . . . . . . . . . . . . . 8" main cone with secondary
high frequency cone
Maximum Amplifier Output . . . . . .1W
Typical Operational Current . . . . .1 CU (50 mA)
Input Impedance . . . . . . . . . . . . . .2000 ohms
Typical Input Sensitivity . . . . . . . . .125 mV rms
Supply Voltage . . . . . . . . . . . . . . . .24V DC
Magnet Weight . . . . . . . . . . . . . . . .10 oz.
Connection . . . . . . . . . . . . . . . . . . .Via wire nuts (included in electrical box)
Dimensions . . . . . . . . . . . . . . . . . .23-7/8" W x 5" H x 23 -7/8" D
Product Weight . . . . . . . . . . . . . . .12 lb.
Plenum-rated, complies with requirements of standard UL-2043.
The speaker shall be a Bogen Model ACD2X2 Drop-In Self-Amplified Ceiling Speaker, which shall be fully enclosed and construct-
ed of industrial grade steel. It shall be comprised of a damped high-compliance factory-mounted loudspeaker that shall consist of
an 8" treated paper main cone, a secondary high frequency cone, and a 10-ounce magnet. The unit shall have a 1-watt amplifier.
The typical current consumption shall be 1 CU (50 mA). Frequency response shall be 95 Hz - 12 kHz. Input sensitivity shall be 125
mV rms with max. SPL @ 94 dB (1M). Input impedance shall be 2k ohms. Dispersion shall be 100°. The speaker shall have a non-
reflective, off-white or bright white (“U” version) finish metal grille with a recessed volume control accessible through front grille.
The speaker assembly will fit into 2' x 2' and 2' x 4' ceiling grids. For 2' x 2' installations, support rails shall not be required and no
cuts to the ceiling shall be necessary. For 2' x 4' installations, a single cut to the ceiling tile and an included support rail shall be
required. The speaker shall measure 23-7/8" W x 5" H x 23-7/8" D and shall weigh 12 lb.
SPECIFICATIONS
Architect and Engineer Specifications
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel: [phone] Fax: [phone] www.bogen.com
Specifications subject to change without notice.
© 2006 Bogen Communications, Inc.
Part No. 54-9273-01B 0803
Self-Amplified Drop-In Ceiling Speaker: ACD2X2 & ACD2X2U
ACD2X2
ACD2X2U
Model
Off-white Finish Bright White Finish (U) Back Can Recessed Volume Control
●
●
●
●
●
●
Lead Color
70V Red
25V Yellow
COM Black