Bolt VX-710N User manual

VX-710N
TTL FLASH
User’s Manual
Inspiration strikes.
Inspiration strikes.

2 |Introduction
Copyright © 2012 Gradus Group.
Bolt and other names of Bolt products are trademarks of Gradus Group. Other product and corporate names mentioned herein are trademarks of their respective holders.

Introduction |3
Introduction
Thank you for choosing the Bolt VX-710N Flash. This advanced digital ash unit puts creative control in your
hands with a broad range of automatic and manual features. It can be used as both an on-camera ash and as
a wireless slave ash. Among the benets you’ll enjoy:
• Full compatibility with Nikon’s i-TTL metering system
• Flash exposure bracketing
• Automatic and manual zoom from 24mm to 180mm
• Tilt and swivel head: -7° down, 90° up, 180° right, and 90° left
• Two-inch backlit LCD
• Eight manual ash levels: full to 1/128 power, plus ne-tuning by 1/3
• Autofocus-assist for low-light photography
• Wireless optical slave
• Rear-curtain sync
• Built-in reector and diffuser panels
• Automatic power-saving function

4 |Contents
Contents
Introduction ..................................................................................................................................................2-3
Overview ......................................................................................................................................................6-9
Warnings ..................................................................................................................................................10-12
Installing Batteries ....................................................................................................................................12-13
Mounting the Flash ...................................................................................................................................14-15
Turning on the Flash and Firing a Test.......................................................................................................16-18
Extended Interface....................................................................................................................................19-20
Using the Automatic TTL Flash Mode ............................................................................................................. 21
Locking Flash Value ....................................................................................................................................... 22
Using Flash Exposure Compensation.............................................................................................................. 23
Red-Eye Reduction ........................................................................................................................................ 24
Using Flash Exposure Bracketing ................................................................................................................... 24
Using the Manual Flash Mode ...................................................................................................................25-26

Contents |5
Controlling Flash Coverage (Zoom)............................................................................................................27-29
Using the Autofocus-Assist Light.................................................................................................................... 30
Bouncing Your Flash..................................................................................................................................30-32
Using Rear- or Second-Curtain Synchronization ............................................................................................. 33
Using Your VX-710N as a Wireless Manual Slave.......................................................................................34-36
Positioning Slave Flash Units.....................................................................................................................36-37
Troubleshooting ........................................................................................................................................38-39
Specications ................................................................................................................................................ 40
FCC Notices................................................................................................................................................... 41
Notes............................................................................................................................................................. 42
Limited Warranty ........................................................................................................................................... 43
Customer Service .......................................................................................................................................... 43

6 |Overview
VX-710N
2
1
4
5
6
3
7
8
10
11
12
13
15
14
16
17
19
20
22
21
18
9

Overview |7
Overview
1. Flash head
2. Reector panel
3. Diffuser panel
4. AF assist light
5. Wireless slave sensor
6. Locking wheel
7. Mounting foot
8. Extended interface cover
9. Power source socket
10. PC sync terminal
11. Flash head position indicator (tilt)
12. Flash head position indicator (swivel)
13. LCD
14. Audio button
15. Lock button
16. Pilot button
17. Mode button
18. Navigation buttons
19. Power switch
20. Flash ready light
21. Zoom position button
22. Battery compartment cover

8 |Overview
Zoom
ISO
23 24 25
29 30 31 32 34 35 3633
37
40
26
27
28
38
39

Overview |9
23. TTL mode
24. Manual zoom mode
25. Zoom position
26. Flash exposure compensation
27. Manual mode
28. ISO speed
29. Lock icon
30. Sound icon
31. Low battery icon
32. Thermal warning icon
33. Manual ash output / Flash
exposure compensation value
34. Camera communication icon
35. S1/S2 wireless ash mode icon
36. Rear-curtain sync icon
37. Camera aperture (f-stop) / Manual
ash 1/3-stop increment
38. PC sync cord
39. Soft case
40. Stand / Tripod mount

10 |Warnings
Warnings
Before using your VX-710N, please read the following safety notices carefully and thoroughly to ensure safe
use, and to help prevent damage to your ash or injury to yourself or others.
• Do not re the ash at close range directly into the eyes of people or animals. This can cause damage to
the retina and may even lead to blindness.
• To avoid overheating and damaging your ash unit, please wait for at least ten minutes after twenty-ve
continuous ashes at full power.
• Do not disassemble or attempt to repair this product yourself. There are high-voltage components inside
that can produce a hazardous electric shock.
• Keep this product and its batteries out of the reach of children.
• Use only the power sources specied in this manual.
• Always switch the ash off before changing the batteries.
• Always install AA batteries of the same type, brand, and age. Do not combine different types or brands, or
old and new batteries. This can cause the batteries to leak, overheat, or explode.
• Install the batteries in the proper orientation, according to the indicator in the battery chamber. Installing
batteries in the reverse orientation may cause them to leak, overheat, or explode.

Warnings |11
• Do not use or store the VX-710N in ammable conditions (such as environments containing ammable
gases or liquid chemicals). This can damage the ash, start a re, or cause an electric shock.
• Do not clean the VX-710N with agents containing corrosive or ammable substances such as paint thinner,
benzene, or nail polish remover.
• This product is not water resistant. Keep it away from rain, snow, humidity, and general moisture.
• Should the VX-710N sustain physical damage, do not touch any exposed interior metal parts. If touched,
they may generate an electric shock or cause a malfunction. Promptly remove the batteries and take the
product to an authorized service center for repair.
• If you detect excessive heat, smoke, or a burning smell coming from the ash, immediately stop operation
and remove the batteries to prevent the product from igniting or melting. Take the product to an authorized
service center for repair.
• Do not drop or otherwise cause a strong physical impact to the VX-710N, as this can cause a malfunction
that may cause it to explode or ignite.
• Remove all batteries from the VX-710N before long-term storage in order to prevent the product from
igniting or leaking corrosive liquids.
• Do not store or use this product at temperatures above 104°F (40°C).
• Keep the metal contacts in the battery compartment clean and free of corrosion and dirt. Do not touch
them with your ngers. Corrosive elements on the contacts can damage the VX-710N and prevent it from
functioning properly. Contacts may be cleaned with isopropyl alcohol on a cotton swab.

12 |Installing Batteries
• Dispose of used batteries properly. Never heat them or throw them into a re, as this can cause the
batteries to leak corrosive liquids, generate heat, or explode.
Installing Batteries
The VX-710N can be powered by four AA batteries of several types:
• Lithium (1.5 V)
• Nickel-metal hydride (Ni-MH) (1.2 V)
• Alkaline (1.5 V)
Note: For the fastest recycle times and longest battery life, lithium or Ni-MH batteries are recommended.
To install batteries, make sure the VX-710N is turned off and follow these steps:
1. Press on the battery compartment cover and slide it in the direction of the arrow to open it.
2. Insert batteries in the orientations indicated by the illustrations inside the compartment.

Installing Batteries |13
3. Close the battery compartment cover by pressing and sliding it into place, in the opposite direction of the
arrow on the cover.
123
1
21
2
When the battery power is low, the low battery indicator ( ) will appear on the LCD, the ash ready light will
turn red for twenty seconds or longer, and the ash will continuously beep for approximately ten seconds.
Important! Replace all four batteries at the same time. Do not mix battery types or brands, or use old and new
batteries together.

14 |Mounting the Flash
Mounting the Flash
To mount the ash on your camera, make sure the VX-710N is turned off and follow these steps:
1. Rotate the locking wheel counterclockwise to loosen it.
2. Slide the mounting foot all the way into your camera’s hot shoe.
3. Rotate the locking wheel clockwise until secure.
2 31

Mounting the Flash |15
To dismount the ash from your camera, make sure the
VX-710N is turned off and follow these steps:
1. Rotate the locking wheel counterclockwise to release the ash.
2. Slide the mounting foot out of your camera’s hot shoe.
Mounting the VX-710N on the included stand:
You can mount the VX-710N on the included stand in the same way you would mount it on your camera. This
allows you to set the ash up on a at surface, or to attach it to a tripod head, light stand, or clamp that has a
compatible 1/4”-20 screw mount.

16 |Turning on the Flash and Firing a Test
Turning on the Flash and Firing a Test
To turn the ash on, slide the power switch to the ON position.
Flash ready light: The ash ready light indicates the status of
your ash:
Color of ash ready light Status of VX-710N Operation
Green Flash ready Normal
Red Recycling Normal
Red for 20+ seconds Battery low Replace batteries
If the ash is mounted on your camera, a ash icon will also appear in the camera’s viewnder.
To re a test ash, press the PILOT button.

Turning on the Flash and Firing a Test |17
Automatic power-saving function: After three minutes of inactivity, the ash will automatically enter power-
saving mode to conserve battery life. The LCD and the ash ready light will turn off. To reactivate the VX-710N,
press the PILOT button or press your camera’s shutter-release button halfway. During long periods of inactivity,
use the power switch to turn the ash off completely.
LCD illumination: When you turn the ash on or press any button, the LCD will be illuminated for about six
seconds.
Audio monitor: The audio monitor feature causes the ash to emit one or more beeps to indicate the status of
the ash:
Audio monitor Status of VX-710N Operation
One beep Pressed button/red ash Normal
Two beeps Flash ready Normal
Long beep for 10+ seconds Entering overheating protection
mode
Turn the ash off for 10 minutes
to let it cool off
Continuous beeping for approx.
10 seconds
Low battery warning Replace batteries

18 |Turning on the Flash and Firing a Test
To turn on the audio monitor, press the AUDIO ( ) button. The audio icon ( ) will appear on the LCD, and the
ash will emit a beep. Repeat this step to disable the audio monitor. Note that the low battery warning will
sound even if the audio monitor is off.
Lock mode: To prevent inadvertent operation of your ash, you can lock it by setting it to lock mode. To lock
the device, press and hold the LOCK button ( ) until the lock icon ( ) appears on the LCD. Repeat this step to
unlock the device.
Important!
Make sure that slave mode is turned off when mounting the VX-710N on your camera. Turn it on only when
using the ash as an off-camera wireless slave.
Overheating protection mode: If the operating temperature of the VX-710N is too high, or after 25 continuous
ashes at 1/1 (full power), the ash will enter overheating protection mode. The thermal warning icon ( ) will
appear on the LCD, the unit will emit a long beep for over ten seconds, and you will be unable to re a ash.
We suggest you turn the unit off for ten minutes to let it cool down.

Extended Interface |19
Extended Interface
You can connect your VX-710N to an external power source or PC sync via the extended interface on the side
of the ash.
External power source: An external power source, such as the Bolt Cyclone Battery Pack, can greatly
increase the battery life of your ash and reduce the recycle time in between ashes.
Note: When using an external power source, the AA batteries must still be in the ash in order to operate.
PC Sync: You can synchronize your VX-710N with a camera by running a PC cord between your camera and
the VX-710N’s PC sync terminal. This lets you position the ash away from the camera, thus giving you more
lighting options.
Note: The PC sync terminal on the VX-710N is only for synchronous signal input, and not output.

20 |Extended Interface
To access the extended interface, follow these steps:
1. Pull back the contact cover on the side of the ash.
2. Plug the cable into the corresponding socket or terminal.
A. For an external power source, plug the power cable
(Canon CZ-type, not included) into the external
power source socket.
B. For PC sync, plug the PC cord into the PC sync
terminal.
Note: When using both cables at the same time, rst insert the PC cord and then insert the power cord. Very
rarely, a thick-proled PC cord will not t at the same time as the power cable. In that case, use the supplied
PC cord.