Bon Pergola Villa Pergola User manual

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
User Instructions
Villa Pergola motorized operation
Size: 13’x19’ Double Bay
( 400 x 600cm )
*Please visit www.bonpergola.com for the
latest instruction under Q&A section*
Size: 13’x19’
151"
157"
106" 106"
228"
97 1/2"
104"
v2023.01

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Content
Tools and man force ............................................................................3
Parts List..............................................................................................3-4
Product Description..............................................................................5
Safety Instruction..................................................................................5
Mounting................................................................................................6-19
Dismounting...........................................................................................21
Storage...................................................................................................21
Disposal..................................................................................................21
Dear Customer,
Congratulations and welcome to our Villa Pergola family. To enjoy your Villa Pergola for
its lifetime and for you and other’s safety, please follow the assembly instructions.
Before you start the assembly process and using the Pergola, we suggest you are best
to get familiar with this product. Make sure all parts listed up in below packing lists are
delivered and intact. If you find that there are parts missing or damaged please do not
install the pergola but contact us immediately. Do not start the assembly process if parts are
missing or defective.
Attention:
Read this instruction manual carefully and completely before mounting and usage.
Keep this manual for future reference.

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Parts List
*Please check all parts against the parts list before commencing construction of pergola.*
Tools and man force
Recommended: 2 or 3 people
Additional tools :
1. Ladder
2. M10/13 open wrench supplied
3. Rubber mallet
4. Tape measure
5. 5mm hexagon wrench supplied
6. Pencil
7. Spirit level
8. Electric drill
123
SIZE:13’x19’ or 400X600CM PARTS LIST:
x12
x2
x3
x2
x2
x148 x2
x4
x2
x6
x6
Gutter connector
M8X100 expansion bolt
M8x20 Hexagon bolt
M10 screw cap
Upright cover
Base plate
50 to 40 connector
M8x20 countersunk screw
3
4
5
6
x124
Plastic Spacer Wall Bracket
Slider
7
x124
Locking nut
8
x2
Motor with motor bracket L bracket
Cover plate
9
15
10
11
12
1
2
x3
Footing plate cover
16
x12
M10X100 expansion bolt
17 x12
13
14
>1.5m
x2

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
A1
B1
C1
C2
C3
x1
x1
x1
x1 Beam
Wall mount beam
Wall mount beam
x1 Beam
B2
x1
A2
SIZE:13’x19’ or 400X600CM PARTS LIST:
*Please check all parts against the parts list before commencing construction of pergola.*
x2
x2
x2
x4
x58
x2
Connecting rod
Driving louver
Centre louver
Common louver
Gutter
Gutter
x2 Gutter
Post +
post connector
E1
E2
F1
x2 Gutter
F2
x1 Center Beam
x1
D1
x1
D2
x1
D3
G
H
I
J
Louver beam with motorize connection
Louver beam with motorize connection

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Product Description:
Important Safety Instructions:
Make the most of your outdoor living area with your pergola.
Relax and enjoy the outdoors while being protected from sun.
The coated aluminum frame pergola is perfect for shading your garden, deck,
courtyard and swimming pool.
Warning: For the safety of you and other persons it is important to follow below
instructions and obey warnings.
Symbol explanation
Safety instructions
This warning triangle calls attention to hazards that that can lead to death
or to severe injuries or which are important for the functioning of the Pergola.
This sign identifies important notes.
• you are unsure if the pergola can be mounted on the place you chose for installation.
• you do not understand the instruction manual or parts of it.
• you do not have necessary tools available.
• you do not have necessary technical knowledge
To install this pergola technical knowledge is necessary.
Do not mount this pergola yourself but contact a professional workman for help if
A minimum of three healthy adults are required to move and install the pergolaas the
product is big and heavy. Do not try to install the pergola alone. If the pergola falls,
it could cause serious injuries and damages! Contact an authorized assembler for help.
Do not install the pergola when you find damage parts are that parts are missing.
Contact your dealer.
Keep children and pets out of the working area during assembly and adjustments.
This product and its fixing parts are only suitable for installation on a plain cement
wall or stable brickwork. If the wall/brickwork shows cracks you have to consult a professional.
Nobody is allowed to change the products’ design and structure without the permission
of manufacture or authorized deputy.
Please make sure that your hands are clean at the time of the assembly;
otherwise you may soil frame.
Nobody is allowed to climb onto the Pergola. Hanging anything on the Pergola is forbidden.
Sheeting was used to protect the paint. This must be removed afterwards.
This structure is a non-permanent structure and the warranty does not cover damage incurred
under extreme weather conditions including heavy rain, high winds or if exposed to high heat
from heaters or BBQs.
Safety precautions should always be followed when assembling and using this product to
reduce the risk of personal injury and damage to equipment. Please read all instructions
before assembly and use. Never leave children unattended around/under this pergola.
Do not attempt to assemble or use the pergola in moderate or heavy wind conditions.
Always keep the pergola louver open and secure it during heavy winds or extreme weather
conditions to avoid damage to the pergola or personal injury.

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 1
Attach base plate ③x2 to the bottom of posts ( D1 x1, D2 x1 ,and ),use bolts ①x8 to attach
with hex key or electric drill
D1 D2 posts should be installed diagonally as below
D1
D2
D3
x1
Post +
post connector
x3
Base plate
x12
M8x20
countersunk screw
x2
Footing plate cover
Optional
16
***NOTE: If you will need to cover the anchor with
footing plate cover, put them on before attach base
plate to post
D3
D2
D1
Optional
16

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 2
C2 x1
Beam
x6
M8X100 expansion bolt
Wall Bracket
15
11 x12
According the height of C2 to measure the height of 15 ,use anchor to fasten
C2
D1
D2
D3
H
H
W W W W W
15
11
D2
C2
D3
C2

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 3
Use bolts 12 x6 to fasten beam B1 & beam B2
D1
D2
D3
x6
Slider
12
B1
B2
x1
Beam with motor direction & slots
12
11
B1
B2
B1
B2

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 4
Connect A2 / B2 with 13 ,fasten the screws,and insert the middle beam C3 Lock the screws.
Connect the B1 and B2 , insert C1 into D3 , fasten the screws.
x15
M8x20 Hexagon bolt
6
C2
x1
Beam
x1
L bracket
13
Beam with motor
direction & slots
x1
A2
C3 x1
Center Beam
A2
A2
C2
C2
C2
C3 B2
A2
B2
A2
D2
D3
D1
C3
C2
D3
B2
B1
B1
C3

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 5
Insert the A1 / C1 into D1 ,then connect B1 with 13 ,fasten the screws.
x1
M8x20 Hexagon bolt
C1 x1
Beam
x1
L bracket
13
Beam with motor direction & slots
x1
A1
A1 A1
C1 C1
C2
C3 B2
A2
D2
D3
D1
C3
C2
C1
D3
A1 B1
C1
A1
B1

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 6
Cover the post with x 2,fasten the screws.
4
x2
Upright cover
4
x4
M8x20 Hexagon bolt
6
Cover the beam on both sides with ,fasten the screws
14
x2
Cover plate
14
C2
C3
B2
A2
A2
D1
A1 B1
C1
D2
D3
14
B2

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 7
x1
Motor with motor bracket
E1
E2
x1
Gutter
F1
F2
9
Placed all gutter E1 , E2 , F1 , F2 in proper position as picture
9
F1
9
F1
E1
E2
F1
F2
E1
E2
F1
F2
D3
D2
D1

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 8
1. Fasten ⑩x2 gutter connector
2. If motor wire is running downward through the post, use ②to connect
with ⑩as shown below to not allow water drain through this post.
x2
50 to 40 connector
x2
Gutter connector
10
2
10
F1
E1
10
D3
D1
D2
E1
F1
E1
F1

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 9
Fasten motor ⑨x2 with its screws as shown below.
x2
Motor with motor bracket
9
E1
E2
F1
F2
E1
E2
F1
F2
D3
D1
D2
9

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 10
Connect the female and male plugs for the LED lighting
(DC24V to DC24V) and motor (DC24V to DC24V) and
Plug the power cable into local socket.
***Note: You can test your motor at this stage. Plug in and use its remote.
x2
Motor with motor bracket
E1
E2
F1
F2
E1
E2
F1
F2
D3
D1
D2
9
Main power
Poqwe plug
DC24V
DC24V
Main power
DC24V for motor
DC24V for light
Poqwe plug

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 11
x2
M10 screw cap G
x58
Common louver
H
x2
Centre louver I
x2
Driving louver
9
9
I
I
9
9
I
I
Place center louver H into 16th slot, lining up with the holes
Using M10 nut ⑤x2, secure the louver in place
Place Steering louvers I x2 in line with 7th slot on the beam A1 and A2
Fit all common louvers G x58 into the remaining slots in the beams
A2
A1
H
G

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 12
x124
Locking nut
x124
Plastic Spacer
x124
M8x20 Hexagon bolt
Jx2
Connecting rod
Fix J x 4 (flat L-shaped aluminum profile).
One for each other of the slats is required.
Use bolt ⑥x124, plastic spacer ⑦ x124 and nut ⑧ x124 to tighten for 600X400cm size.
Secure the louvers at each end.
***NOTE:
1. Do not over tighten. If over tighten, louver will not move and possibly damage the
louver driver component. Please test the louvers are rotatable by hands smooth and
easy to confirm it's not over tighten.
2. Please make sure the Nylon Washer is in between the J and Louver End Cap.

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 13
*Check for diagonal distance in between the posts L1~L4 and K1~K4 are equal.
*Please note, this step is very important to ensure the pergola are in a rectangle shape in any angle.
It’s extremely important if you are installing a screen before anchor the pergola down or afterward.
L2
L1
L3
L4
K6
K4
K2
K3
K1
K5
PostPostPost
Wall
L L
KKK

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Step 14
IMPORTANT NOTE:
If you order the screens, please anchor down the pergola to the ground AFTER
installing the screens onto the pergola as it might require minor adjustment to
make screens fit perfectly.
WARNING:
Make Sure louvers are open during periods of mild to strong winds to avoid damage overtime
Mark holes for Wedge Anchor/Bolt x12 for each post
Note the drill size should be 12 mm.
Insert the bolts. Use a hammer drill if necessary. Place the posts
over the bolts. Tighten the nuts.
Once installed, make sure any remaining plastic is removed and silicone is used
along all corners and gutters to be waterproof.
17
x12
M10X100 expansion bolt
17
x4
17

01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16 17 18 19 20
Motor set up
※86mm*86mm, in accordance with international installation standard;
※The electric structure is partial conformity with the standard fire protection requirement of the electrician;
※Industrial grade microcomputer chip is used to improve product quality and reliability greatly;
※Use shock-proof current relay;
※Components using precision SMT industry, surface moisture-proof treatment;
※Power supply has safety protection, power supply time is 5 minutes;
※It is used with various emiters and tubular motors.
1.Function and Features
HC-PM03F\D-T1
① Motor: Up button
② Motor: Stop button
③ Motor: Down button
④ Light bulb: turn on/off button
HC-PM03\D-T1
⑤ Motor: Up button
⑥ Motor: Stop button
⑦ Motor: Down button
⑧ Light bulb: turn on/off button
Product name Remote controller with light control
Product model
Receiving/
transmitting frequency
Working temperature -20℃~+85℃
Receiving sensitivity -110dBm
Allowed number of
transmitters
3-2
*Within 7 seconds after plug in or power on*
Open the back cover of the remote control and
press and hold the code key for more than 5 seconds
with a fine needle.
3-3
When the motor keeps beeping “dididi”
3-4
Press the “up button” of the remote
control once and hear the beep of the
motor, and the code matching is
successful
3-4
Press the “down button” of the remote
control once and hear the beep of the
motor, and the code matching is
successful
HC-PM03F\D-T1
≤8pcs
433.92MHz
Product name Remote controller with light control
Product model
Receiving/
transmitting frequency
Working temperature -20℃~+85℃
Receiving sensitivity -110dBm
Allowed number of
transmitters
HC-PM03\D-T1
≤8pcs
433.92MHz
5 seconds
3-1
Must unplug over 10
seconds before plug in
2.Product Parameters
3.Operating Instruction
A. Learning code
B. Deleting code 3-3
When the motor keeps beeping “dididi”
5 seconds