Borroughs 50195 User manual

- 1 -
IMPORTANT - PRODUCT LIABILITY INFORMATION
Read all instructions before proceeding with installation. Vital product information pertaining to proper set-up and cautions are included.
Failure to follow these instructions may result in personal injury and/or property damage.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
Sloped Top Shop Desk
and
Cabinet Conversion Kit
Assembly Instructions
09-50195-00B
JUNE 1998
(logo rev. 2004)
3002 N. BURDICK ST.  KALAMAZOO, MI 49004-3483
800-748-0227  FAX: [phone]  .borroughs.com

- 2 -
3. Using four (4) nuts and screws (Items 6 & 7
respectively) for each leg assembly (Item 3),
attach one leg assembly to each corner of the
shop desk assembly. See Figure 2. Finger
tighten only - sixteen (16) nuts and screws.
FIGURE 2
2. Stand the shop desk assembly (Item 1) on its
back with top in open position. See Figure 1.
1. Remove all items from carton and check parts against the following list:
PARTS LIST "A"
Item Description Required
1 Shop Desk Assembly 1
2 Rack Assembly 1
3 Leg Assembly - 39" 4
4 Stringer 2
5 Shelf 1
6 5/16-18 Keps Nut - Zinc Plated 24
7 5/16-18 x 1/2 Phillips T.H.M.S. - Zinc Plated 24
8 No. 10 x 3/8 T.H.S.M.S. - Zinc Plated 4
9 Rubber Bumper 2
10 Lock Assembly 1
Sloped Top Shop Desk Assembly Instructions (Cabinet Conversion Kit instructions begin on page 4)
FIGURE 1
SHOP DESK
TOP
SHOP DESK BOTTOM
~
~
Tools Required: 1. 1/2" Open End Wrench
2. Phillips Screwdriver
SCREW
NUT

- 3 -
4. Making sure hands are clear, CLOSE TOP and
stand desk upright. Attach stringers (Item 4) with
four (4) nuts and screws (Items 6 & 7) - two (2)
each side - in the bottom holes on the inside of
the leg assembly. See Figure 3. Finger tighten
only.
FIGURE 3
5. Attach shelf (Item 5) to the stringers in the front
and to the leg assemblies in the rear with four (4)
nuts and screws (Items 6 & 7) - two (2) each side
as shown. See Figure 4. Finger tighten only.
6. Position rack assembly (Item 2) on top of desk,
align holes and fasten together with four (4) sheet
metal screws (Item 8) as shown. See Figure 5.
Tighten with a Phillips screwdriver.
7. Insert rubber bumpers (Item 9) into slots on the
side edges of the desk. See Figure 5.
C A U T I O N
VERY IMPORTANT - Move desk into workstation position and level.
TIGHTEN ALL SCREWS and NUTS with a 1/2" wrench and a Phillips screwdriver.
8. Insert lock (Item 10) into lock hole in desk front. Open top and slide snap fastener over lock, securing it in place. Close
top. Insert key and test locking capability.
C A U T I O N
MAKE SURE ALL HANDS AND FINGERS ARE CLEAR BEFORE CLOSING TOP.
DO NOT LEAVE OPEN AND UNATTENDED.
DO NOT WEDGE OPEN.
FIGURE 4
FIGURE 5
SHEET METAL
SCREWS
RUBBER
BUMPER
NUT
STRINGER
SCREW
SCREW
NUT
SCREW

- 4 - FIGURE 6
RACK
~
STRINGER
~
STRINGER
~
SHELF
~
Cabinet Conversion Kit Assembly Instructions
PARTS LIST "B"
Item Description Required
1 Handle Reinforcement 1
2 Door Handle with Lock 1
3 Cam 1
4 #8-32 x 5/16 SEMS Screw 2
5 5/16-18 x 1/2 Phillips T.H.M.S. - Zinc Plated 44
6 5/16 - 18 Keps Nut - Zinc Plated 44
7 Door Frame 1
8 Door - Right Hand 1
9 Door - Left Hand 1
10 Throwbolt 2
11 Back Panel 1
12 Side Panel 2
13 Shelf - Upper 1
14 Shelf - Bottom 1
15 Push Clip 1
1. Remove all items from carton and check parts against the following list:
2. Remove rack, shelf and stringers from desk.
See Figure 6. NOTE: Lay desk upside down
on a clean, smooth surface. Protect top
surface with wooden blocks under front edge
of desk to rest unit in level position.
Tools Required: 1. 1/2" Open End Wrench
2. Phillips Screwdriver

- 5 -
3. Remove doors from door frame (Item 7). See Figure 7.
FIGURE 8
RIGHT HAND DOOR
FIGURE 7
~
~
LEFT HAND DOOR
4. See Figure 8 and . . .
a. Place side panels
(Item 12) and back
panel (Item 11) into
position.
b. Insert door frame
(Item 7) into unit.
NOTE: Tilt frame
between side
panels and pull to
front of unit. Top of
frame must be
down.
c. Fasten side panels,
back panel and
door frame to legs
of desk, with
sixteen (16) screws
and nuts (Items 5 &
6) at two levels
closest to the top of
desk.
3-3/4"
5-7/16"
DOOR FRAME
KEPS NUT (16 req'd.)
BACK PANEL
SIDE PANEL
~
SCREW
(16 req'd.)
SEE
STEP
4 c.
TOP OF DESK
~
SIDE PANEL
~

- 6 -
5. See Figure 9 and . . .
a. Insert upper shelf (Item 13)
and fasten into place with
six (6) screws and nuts
(Items 5 & 6).
b. Fasten side and back
panels to REAR LEGS
ONLY with eight (8) screws
and nuts (Items 5 & 6).
c. Insert bottom shelf and
fasten into place with six (6)
screws and nuts (Items 5 &
6). NOTE: Tilt shelf be-
tween side panels and pull
upward to align shelf with
holes in side and back
panels.
d. Fasten door frame and side
panels to front legs with
eight (8) screws and nuts
(Items 5 & 6).
e. Place shop desk into
upright position.
FIGURE 9
FIGURE 10
RIGHT HAND
DOOR
HANDLE
(Must point toward
bottom of door
during installation)
HANDLE REINFORCEMENT
#8-32 x 5/16 SEMS SCREW
CAM
THROWBOLT
PUSH CLIP
6. See Figure 10 and . . .
a. Fasten handle reinforce-
ment (Item 1) and door
handle with lock (Item 2) to
right hand door with two (2)
screws(Item 4).
b. Place throwbolts (Item 10)
on pins of cam (Item 3) and
fasten to handle with push
clip (Item 15).
~
~
SEE
STEP
5 b.
SEE
STEP
5 d.
UPPER
SHELF
BOTTOM
SHELF

- 7 -
7. Attach left hand and right hand doors (Items 8 & 9)
to door frame by inserting hinge pins into hinge
sockets.
8. Fasten rack into original position on desk with four
(4) screws.
FIGURE 11

- 8 -
NOTICE:
Borroughs Corporation extends to the original purchaser from the date of purchase, a 5-year limited warranty against manufacturing defects in material and workmanship. If a
Borroughs product fails to perform because of a manufacturing defect, Borroughs will examine it. If found defective, it will be repaired or replaced at our option. This warranty
applies only to Borroughs products acquired directly from Borroughs Corporation or from Authorized Borroughs Dealers.This warranty does not apply to any product which has
been subject to misuse, negligence, or accident; has been damaged in shipment, storage, or installation; has been misapplied or has been modified or repaired by unauthorized
persons or been repaired with non-standard Borroughs replacements parts.This warranty specifically excludes claims for indirect, incidental, or consequential damages arising
in any way from a product defect. This warranty is exclusive, and exists in lieu of all other warranties, either express or implied. This warranty gives you specific legal rights; you
may also have other rights which may vary from state to state. To obtain warranty service, contact your Borroughs Selling Dealer.You must make a written claim. Provide a copy
of your purchase record and a written description of the warranty problem with your claim. If you are unable to contact your Dealer, contact: Borroughs Corporation, Customer
Service Manager, 3002 N. Burdick Street, Kalamazoo, MI 49004-3483.