Bosch SGE63E06UC/32 User manual

9000644617

IMPORTANT SAFETY INSTRUCTIONS:
SAVE THESE INSTRUCTIONS
To avoid possible injury or property damage, OBSERVE
ALL WARNINGS AND CAUTIONS.
These instructions are intended for use by qualified
installers only. The dishwasher must be installed by a
qualified service technician or installer.
In addition to these instructions, the dishwasher shall
be installed to meet all electrical and plumbing codes
and ordinances (both national and local).
Read these installation instructions completely and
follow them carefully. They wiJJsave you time and ef-
fort and help to ensure safety and optimum dishwasher
performance.
iM PO RTANT
" The dishwasher drain hose must be instaJJed with a
portion of it at least 20" (508mm) off the cabinet floor;
otherwise the dishwasher may not drain properly.
,, This dishwasher is intended for indoor residential
use only, and should not be used in commercial food
service establishments.
• NEW INSTALLATION - If the dishwasher is a new
installation, most of the work must be done before the
dishwasher is moved into place.
• REPLACEMENT- If the dishwasher is replacing an-
other dishwasher, check the existing dishwasher con-
nections for compatibility with the new dishwasher, and
replace parts as necessary.
• This appliance has been found to be in compliance
with CAN/CSA-C22.2 No. 167/UL 749. It is the respon-
sibility of the owner and the installer to determine if
additional requirements and standards apply in specific
installations.
• Not for outdoor use.
Inspect the Dishwasher
After unpacking the dishwasher and prior to installation,
thoroughly inspect the dishwasher for possible freight
or cosmetic damage. Report any damage immediately.
Cosmetic defects must be reported within 30 days of
installation.
NOTE: Do not discard any bags or items that come with
the original package until after the entire installation
has been completed.
2

Avoiding General Hazards
Do not use the dishwasher untiJ it is compJeteJy
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while supporting
the rear of the unit. Failure to follow this warning can
cause the dishwasher to tip over and result in serious
injury.
Before installing the "L"-shaped supplied counter-
top mounting brackets (select models), decide which
method will be used to secure the dishwasher into its
opening. Once these mounting brackets are installed
on the dishwasher, removing them is difficult and will
damage the mounting brackets and the dishwasher.
In some conditions, hydrogen gas can form in a
hot water system that has not been used for weeks.
Hydrogen gas is explosive.
Before filling a dishwasher from a system that has
been off for weeks, run the water from a nearby faucet
in a well ventilated area until there is no sound or evi-
dence of gas.
Temperatures required for soldering and sweating will
damage the dishwasher's base and water inlet valve.
If plumbing lines are to be soldered or sweated, keep
the heat source at least 6 inches (152.4 ram) away from
the dishwasher's base and water inlet valve.
Removing any cover or pulling the dishwasher from the
cabinet can expose hot water connections, electrical
power and sharp edges or points. Handle with care.
The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with
all national and local electrical codes and ordinances.
The dishwasher is designed for an electrical supply
of 120V, 60 Hz, AC, connected to a dishwasher-
dedicated, properly grounded electrical circuit with
a fuse or breaker rated for 15 amps. Electrical supply
conductors shall be a minimum #14 AWG copper only
wire rated at 75°C (167°F) or higher.
This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the appliance. Do not
use extension cords.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative
if you are in doubt whether the appliance is properly
grounded. Do not modify the plug provided with the
appliance, if it will not fit the outlet, have a proper
outlet installed by a qualified electrician. A
Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water
line. Serious injury could result. Only qualified
plumbershould perform plumbing work. Do not
attempt any work on the dishwasher hot water supply
plumbing until you are certain the hot water supply is
shut off.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to
touch. Separate channels are provided under the dish-
washer.
Do not work on an energized circuit. Doing so could
result in serious injury or death. Only qualified electri-
cians should perform electrical work. Do not attempt
any work on the dishwasher electric supply circuit
until you are certain the circuit is de-energized.
Do not over tighten the 90 ° elbow. Doing so may
damage the water inlet valve and cause a water leak.
Temperatures required for soldering and sweating
will damage the dishwasher's water inlet valve. If
plumbing lines are to be soldered or sweated, keep
the heat source at least 6 inches (152.4 ram) away from
the dishwasher's water inlet valve.
Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
Make sure electrical work is properly installed. There
should be no loose electrical connections. Ensure all
electrical connections are properly made.
These instructions depict an installation method for
stainless steel braided hose or PEX hot water supply
lines. If using copper tubing or other material for
water supply, defer to a licensed plumber for proper
installation.

Hammer Hole Saw Pipe Wrench Adjustable Wrench
Tape Measure Slot Screwdriver Phillips Screwdriver T-20 Screwdriver
Wire Cutter Wire Stripper Leve I
,,,%,
Electrical Supply Cable - Minimum #14 AWG, 2 conduc-
tor, 1 ground, insulated copper conductors rated 75 C or
higher.
Hot Water Supply Line - Minimum 3/8" O.D. copper tub-
ing or metal braided dishwasher supply line.
Shut-off valve and fittings appropriate for hot water sup-
ply line (copper tubing/compression fitting, or braided
hose).
UL listed conduit connector or strain relief is required if
you attach the field wiring directly to the terminal block.
4

(b--
0 4x13
(9-
%
A Extra Tall Item Sprinkler (See Use and Care Manual)
B Toe Panel Screws
C Mounting Brackets
D Mounting Bracket Screws
E Toe Panel (2 pieces)
F Toe Panel caps (select models only)
G Screw Clamp (for hose)
H Water Supply Adaptor Fitting
I Flexible Edge Protector Grommet for electrical wire
J Rubber Drain Hose Adaptor
K Toe Panel Mounting Brackets (select models only)
L Outer toe panel (3rd piece) (select models only)
M Side Mount Force Distributor (Alternate Side Mount only)
N Mounting Bracket Screws (Alternate Side Mount only)
O Junction box/power supply
L
ii '[
_b_i___ 4x36
5

Avoid Scalding or Electrical Shock Hazard!
Make sure the water supply and electrical supply are
shut off before installation or service.
NOTE: This dishwasher is designed to be enclosed on the
top and both sides by standard residential kitchen cabinetry,
Select a location as close to the sink as possible for easy
access to water supply and drain lines.
For proper dishwasher operation and appearance, ensure
that the enclosure is square and has the dimensions shown
in Figure 1 below.
J
After locating the proper place for your new dishwasher,
you will need to make any required openings to allow for
passage of the water, drain and electrical line. In order to
avoid interference with the dishwasher when sliding it into the
cabinet, place your openings within the dimensions shown
in Figure 3 below.
i\
i \
I
0/;
NOTE: If your dishwasher opening width measures >237sA6in
(60.8cm) use the TOP or SIDE MOUNT mounting methods.
If your dishwasher opening width measures <237s/_6in
(60.8cm) use the ALTERNATE SIDE MOUNT mounting
method.
If the dishwasher is to be installed in a corner, make sure that
there is adequate clearance to open the door. See Figure
2 below.
Check
clearance [
between [ Countertop
dishwasher [
door and wall
Avoid Electrical Shock/Fire Hazard
Do not allow the electrical and water supply lines
to touch.
Required Openings:
41/4'' x 2" (108 x 52mm) -
4" x2" (100 x 50mm)-
11/4'' (32ram) diameter -
To pass the included electrical
supply junction box through to
an adjacent cabinet
To passthe included water sup-
ply line toward the water supply
To pass the dishwasher
drain hose toward the drain
connection
NOTE: If the incoming electric supply, water supply and
drain connections are all in the same cabinet, the one
4V4"x 2" (108x 52ram) hole will be large enough for all three
to pass through.
Before sliding the dishwasher into the cabinet, remove the
hose clip at the back of the dishwasher as shown. The hose
clip may be used later to hold the drain hose asshown below.
................... i ........................... i............
6

Avoid Electrical Shock Hazard
Do not work on an energized circuit. Doing so could
result in serious injury or death. Only qualified
electricians should perform electrical work. Do
not attempt any work on the dishwasher electric
supply circuit until you are certain the circuit is de-
energized.
Avoid Fire Hazard
Make sure electrical work is properly installed.
Only qualified electricians should perform
electrical work.
Electrical Supply
The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with all
national and local electrical codes and ordinances. The
dishwasher is designed for an electrical supply of 120V,60
Hz, AC, connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker rated for 15
amps. Electrical supply conductors shall be a minimum #14
AWG copper wire rated at 75°C (167°F) or higher.
Electrical Connection
The dishwasher electrical supply junction box and dedicated
receptacle must be mounted in an accessible cabinet
adjacent to the dishwasher (do not mount the junction box
or receptacle behind the dishwasher). You will need a 41/4''
x 2" (108 x 51ram) opening through the cabinet in order to
pass the junction box through (see Figure 4). If the opening
is made through wood, sand it smooth. If the opening is
made through metal, use the included protective grommet
or other approved method to protect wiring from damage.
Use the four screws included (or appropriate fastener) in the
parts bag to securely mount the junction box so that it can
be easily accessed (see Figure 4). The electrical supply can
be connected in two ways:
li Figure 4
7
Avoid Fire Hazard
Make sure there are no loose electrical connections.
Make sure all electrical connections are properly made.
Grounding Instructions
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for
electric current. This appliance isequipped with a cord having
an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that
is installed and grounded in accordance with all local codes
and ordinances.
The dishwasher must be properly grounded before
operating. This appliance must be connected to a
grounded metal permanent wiring system, or an
equipment grounding conductor must be run with the circuit
conductors and connected to the equipment grounding
terminal or lead on the dishwasher. Make sure that the
dishwasher isconnected to a suitable ground in compliance
with all local codes or, in the absence of a local code, with
the NATIONAL ELECTRICAL CODE in the United States or
the CANADIAN ELECTRIC CODE C22.1-1atest edition in
Canada as well as any provincial/state or municipal or local
codes that apply.
Dishwasher Electrical Rating
Volts Hertz Amperes Watts
120 60 12 1,440
(max)
Method A- Three prong plug and receptacle
Use the included three-prong plug and junction box to
connect to a dedicated household receptacle. Make sure
the household receptacle meets the electrical supply
requirements aswell as national and local codes.

Method B - To permanently connect to house-
hold or field wiring:
1. Remove the dishwasher electrical supply junction box
cover and connect to the power supply cord from the
house installation. See Figure 5.
Figure 5
2. Remove 2" to 3" (51 - 76ram) of the outer casing of the
household or field supply wiring as shown in Figure 6.
Remove 3/8" to 1/2" (10 - 13ram) of the insulation from
each wire as shown in Figure 6.
Hot Water Supply
The hot water heater should be set to deliver approximately
120° F (49° C)water to the dishwasher. Water that istoo hot
can cause some detergents to lose effectiveness. Lower water
temperatures will increase run times. The hot water supply
pressure must be between 15- 145 psi (1 - 10 bar).
IM PORTANT NOTES:
*If using a solder joint instead of a compression fitting, be
sure to make all solder connections before connecting
the water supply line to the dishwasher.
*Make sure there are no sharp bends or kinks in the water
line that might restrict water flow.
.Always use the appropriate seal when making plumbing
connections.
.Before connecting the water supply line to the dish-
washer, flush the incoming water line for approximately
5 minutes to clear any foreign material.
.Turn on the water supply and check for leaks after
connections are made.
Figure 6
I
_--- 2"- 3" ---_-I I
(51ram - 76ram) I
3/8"- 1/2" 1_ 41[
(lOmm- 13mm)
3. Insert the bare copper or green wire(ground) to the
"G" ground connection "___L" of the terminal block
and securely tighten the terminal block screw (see
Figure 5).
4. Insert the white (neutral) wire to the "N" connection of
the terminal block and securely tighten the terminal block
screw.
5. Insert the black(hot) wire to the "L" connection of the
terminal block and securely tighten the terminal block
screw.
6. Check all electrical connections to make sure they are
secure and then attach the junction box cover with the 4
screws.
Avoid Electrical Shock Hazard
To avoid possible injury or property damage,
care should be exercised when the dishwasher is
installed or removed to reduce the likelihood of
damage to the power cord.
Avoid Scald Hazard
Do not perform any work on a charged hot water
line. Serious injury could result. Only qualified
plumbers should perform plumbing work. Do not
attempt any work on the dishwasher hot water
supply plumbing until you are certain the hot water
supply is shut off.
Temperatures required for soldering and sweat-
ing will damage the dishwasher. If plumbing lines
are to be soldered or sweated, keep the heat
source at least 6inches (152.4 mm) away from
the dishwasher.
Connecting the Hot Water Supply
There are two plastic corrugated hoses that exit the back of
the dishwasher. The larger hose, with the brass fitting on the
end, is the water supply hose to the dishwasher (the other
hose isthe dishwasher drain hose). You will need a 3" x 1:s/4''
(76 x 45ram) opening through the cabinet to pass the dish-
washer water supply line through toward the shut off valve.
8

Water Supply Shut Off Valve
Install an easily accessible shut-off valve (not supplied) in
the hot water supply line, as shown in Figure 7. All solder
connections must be made before the water line isconnected
to the dishwasher.
Figure 7
To connect the hot water supply:
1. Assemble the water supply adaptor fitting from the
parts bag onto the dishwasher water supply hose. This
connection does not require Teflon brand tape.
2. Pass the dishwasher water supply line with attached
adaptor through the opening toward the water shut off
valve. Take care not to allow the hose to kink or twist
behind the dishwasher.
3. Connect the dishwasher water supply line with adaptor to
the water shut off valve. You will need to use an approved
dishwasher water supply line with the correct fittings for
this connection. Always use the appropriate seal when
malting plumbing connections.
NOTE: The end tithe dishwasher water inlet hose is heavy
and will need to be supported. It is best to lay the end on
the cabinet floor as shown in Figure 7.
4. After all connections are made, turn on the hot water and
check for leaks.
The dishwasher drain hose may be connected to the house-
hold or field drain plumbing in one of four ways. You will
need a 11/4'' diameter hole in order to pass the drain hose
through the cabinet.
1 Directly to the under sink dishwasher drain connection,
asshown in Figure 8.
2 Directly to a disposer dishwasher drain connection, as
shown in Figure 9.
3 To the under sink dishwasher drain connection through
an air gap, as shown in Figure 10.
4 To a disposer dishwasher drain connection through an air
gap, as shown on Figure 11.
IM PORTANT NOTES:
• If local ordinance require an air gap, install it according
to the manufacturer's instructions.
• If the dishwasher drain hose is to be connected to a
disposer dishwasher drain connection, remove the plug
from the disposer's dishwasher drain connection.
• The dishwasher drain hose must have one place along
its length that issecurely attached 20 inches above the
cabinet floor.
• The drain hose length can be extended if necessary.
The maximum length of the drain hose, including the
hose leading to the air gap, is 150 inches.
Figure 8
Figure 10
Figure 9
Non-Metallic Tie
\
MIN.
20"
Figure 11
9

For a large port, use the drain hose as it is.
For a small port, use the provided Rubber Drain Hose
Adaptor (J).
1. Obtain the Rubber Drain Hose Adaptor (J) from the
Dishwasher Installation Kit (do not substitute).
2. Insert the Rubber Drain Hose Adaptor into the end of
the drain hose (see Figure 12). Be sure to fully insert
the drain hose adaptor.
3. Use the Screw Clamp (G) provided to attach the drain
hose to the house plumbing as shown in Figure 13.
Figure 12
Top Mount is used for countertops made of wood or other
materials that can be easily drilled. Orient the mounting
brackets as shown in Figure 14, and position the two small
tabs on the mounting brackets over the two slots on the
dishwasher's front corners. Pushthe mounting brackets down
firmly to insert the tabs iqto the slots.
©
Figure 13
Top Mount
Figure 14 II
Side Mount isused for countertops made of marble, granite,
or other very hard materials that cannot be easily drilled.
Bend the mounting brackets along the small holes and in the
same direction as the two small tabs. Orient the mounting
brackets as shown in Figure 15, and position the two small
tabs on the mounting brackets over the two slots on the
dishwasher's front corners. Pushthe mounting brackets down
firmly to insert the tabs into the slots.
Side Mount
Figure 15
Before installing the supplied countertop mounting
brackets, decide which method of securing the
dishwasher into its enclosure wi[[ be used. Once the
mounting brackets are installed on the dishwasher,
removin 9 them is difficult and wi[[ damage the
mounting brackets and the dishwasher.
Alternate Side Mount (for opening lessthan 231s/_6in)is used
for countertops made of marble, granite, or other very hard
materials that cannot be easily drilled. Insert a side mount
force distributor (Part M) in each side asshown in Figure 16.
®
The dishwasher can be secured into its enclosure in 3 ways:
NOTE: Ifyour dishwasher opening width measures >23_s/16in
(40.8 cm) use the TOP or SIDE MOUNT mounting methods.
If your dishwasher opening width measures <231s/16 in (40.8
cm) use the ALTERNATE 51DE MOUNT mounting method. IJ
Alternate Side Mount
Figure 16
10

Avoid Tip Over Hazard
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while supporting
the rear of the unit. Failure to follow this warning
can result in serious injury.
LEVELING THE DISHWASHER
The unit should now be ready to slide into the cabinet
opening. To avoid scratching the floor, use floor protection
and caution when sliding the dishwasher into the cabinet.
Make sure that the hoses and cords do not bunch up behind
the unit or kink as you slide the unit back. Make certain to
slide the unit into place before raising the leg levelers.
Level the dishwasher horizontally by turning feet clockwise
to raise or counter-clockwise to lower front of the unit.
Level the dishwasher vertically by turning center screw to
raise or lower the back.
Figure 17
SECURING THE DISHWASHER
1. Drive the mounting screws through the holes in the
mounting brackets as shown for Top (Figure 18), Side
Mount (Figure 19) and Alternate Side Mount (Figure 20).
2. After the unit is installed in the enclosure, leveled and
secured, loci<the two front leg levelers in place by driving
the enclosed leg leveler locking screws into each screw
boss located in front of the levelers.
3. Tighten screws until they are flush with the surface of the
bosses.
11
Figure 18
For Top Mount - Wooden
1//6" (2mm)
Figure 19
For Side Mount - Stone Countertop
~V2" (12mm)
Figure 20
For Alternate Side Mount

Yourdishwashercomeswithathree-piecetoepanel(select
models)toallowheightadjustment.
1. Positiontheslottedreartoepanelonthedishwasherfirst.
Allowittorestonthefloor.
2. Positionthematingfronttoepanelontopofthereartoe
panelallowingtheanglededgeto restonthemating
edgeofthedishwasher.
3. Drivethetwoblackscrews(included)throughtheholein
thetoepaneltosecure.Usethesuppliedscrewstoavoid
damagingthedishwasher.SeeFigure21.
4. Formodelswithoutertoepanel(3rdpiece)slidethe
brackets(K)provided,intotheslotsofthetoepanelyou
justattached.
NOTE: Once you determine the correct position for the
brackets, remove the bracket and bend the metal tab. See
Figure 22. This ensures that the toe panel wont slide in
further than you need.
5. Re-insert the brackets.
6. Attach the outer toe panel (L) onto the brackets and drive
the screws provided in place to secure the toe panel.
NOTE: The rubber piece should remain behind the outer
toe panel.
Figure 21
A
(L)- See Page 5
(K)
Figure 22
12

Your dishwasher requires no special care other than
that described in the Care and Maintenance section of
the Use and Care Manual. If you are having a problem
with your dishwasher, before calling for service please
refer to the Self Help section in the Use and Care
Manual. If service is necessary, contact your dealer or
installer or an authorized service center.
Do not attempt to repair the appliance yourself. Any
work performed by unauthorized personnel may void
the warranty. If you are having a problem with your
dishwasher and are not pleased with the service you
have received, please take the following steps (in the
order listed below) until the problem is corrected to
your satisfaction:
1. Contact your installer or the Authorized Service
Contractor in your area.
2. E-mail us. See your Use and Care Manual for
instructions.
3. Call us at the Customer Service phone number :
1-800-735-4328
Please be sure to include (if you are e-mailing), or have
available (if you are calling), the following information:
• Model number
• Serial number
• Date of original purchase
• Date the problem originated
• Explanation of the problem
• Daytime phone number where you can be reached.
Please make a copy of your invoice and keep it with this
manual. The customer must show proof of purchase to
obtain warranty service.
13

Instructions de s curit
Pour 6viter tout dommage bla propri6t6 ou des blessures
OBSERVER TOUSLES AVERTISSEMENTS.
Ces instructions sont destin6es 9 I'utilisation par un installateur
qualifi6 seulement. Ce lave-vaisselle doit _tre install6 par un
technicien ou un installateur qualifi6 seulement.
• En plus de ces instructions, le lave-vaisselle doit _tre
install6 conform6ment aux codes et reglementations
61ectriques et de plomberie (nationaux et Iocaux).
Lire et observer attentivement toutes les instructions
d'installation. Ceci permettra d'6conomiser temps et argent
tout en assurant la s6curit6 et un rendement optimum du
lave-vaisselle.
IMPORTANT
• Le tuyau de drainage du lave-vaisselle doit _tre install6
avec une portion 9 au moins 20 po (508 mm) au-dessus
du plancher d'armoire, autrement le lave-vaisselle ne
pourra drainer ad6quatement.
• Ce lave-vaisselle est destin_ _ un usage r6sidentiel
seulement et non pour un usage commercial.
• NOUVELLE INSTALLATION - s'il s'agit d'une nouvelle
installation, tout le travail de construction doit _tre fair
avant d'installer le lave-vaisselle.
• REMPLACEMENT- dans ce cas,v6rifier si les connexions
existantes sont compatibles avec celle du nouveau lave-
vaisselle et remplacer les pieces au besoin.
• Cet appareil est conforme aux normes CAN/CSA-C22,2
n°167/UL 749. IIincombe _ I'installateur et au propri6taire
de d6terminer si des exigences additionnelles
s'appliquent _ I'installation sp_cifique.
• N'est pas destin6 _ une utilisation _ I'ext6rieur.
V6rifier le lave-vaisselle
Apres avoir d6ball_ I'appareil et avant I'installation, s'assurer
qu'il n'y a pas de dommages esth6tiques ou causes pendant
le transport. Rapporter tout dommage imm6diatement. Les
dommages esth6tiques doivent _tre rapport6s dans un d61ai
de 30 jours suivant I'installation.
REMARO_UE: ne pas jeter les sacs ni I'emballage tant que
I'installation n'est pas compl6t6e.
importantes
14

Risques d'ordre g@n@ral
Ne pas utiliser le lave-vaisselle avant que 'installation ne
soit completement termin@e. Pour ouvrir la porte d'un lave-
vaisselle encore non installS, il faut le faire soigneusement
en soutenant I'arriere du lave-vaisselle. Le lave-vaisselle
peut en effet tomber en avant si cet avertissement n'est pas
respect@ et cela peut causer de graves d@g_ts.
Avant I'installation des fixations en forme de <<L >>(pour cer-
rains modeles), il faut choisir la m6thode qui sera utilis6e
pour I'ouverture du lave-vaisselle. Une lois que ces fixations
sont install_es sur le lave-vaisselle, il est difficile de les re-
tirer et cela risque d'endommager les fixations et le lave-
vaisselle.
Sous certaines conditions, le systeme d'eau chaude peut
6mettre du gaz hydrogene si le lave-vaisselle n'a pas 6t6
utilis6 pendant plusieurs semaines. Le gaz hydrogene est
un gaz explosif. Avant de refaire fonctionner le lave-vaisselle
apres une Iongue p6riode, faire couler I'eau du robinet le
plus proche dans une zone bien ventil6e jusqu'_ ce qu'il
n'y air plus aucun bruit de gaz ou route autre preuve de sa
pr6sence.
Les temp6ratures n6cessaires pour souder et exsuder ris-
quent d'endommager la base et la soupape d'admission
d'eau du lave-vaisselle. Si la tuyauterie a besoin d'une
soudure ou d'une exsudation, placer la source de chaleur
au moins 6 po (152,4 ram) de la base et de la soupape
d'admission d'eau du lave vaisselle.
Vouloir retirer un des couvercles ou vouloir d_placer le
lavevaisselle de son emplacement peut endommager les
tuyaux d'eau chaude et I'alimentation 61ectrique. Effectuer
ces manipulations avec soin.
Risques d'_lectrocution et d'incendie
Les c_bles &lectriques et les tuyaux d'alimentation en eau
ne doivent pas _tre en contact. Des conduits ind_pendants
sont pr6vus _ cet effet sous le lave-vaisselle.
Effectuer des travaux 61ectriques Iorsque le courant est ou-
vert peut provoquer des blessures graves ou la mort. Seul
un 61ectricien qualifi6 peut r6aliser des manipulations 61ec-
triques. N'effectuer aucune manipulation 61ectrique sur le
lave-vaisselle rant que le courant n'est pas clairement hors
tension.
S'assurer que les travaux 61ectriques soient correctement
r6alis6s. II ne doit y avoir aucun c_ble 61ectrique real fix6 et
aucun raccordement 61ectrique real r6alis6.
Le client _ la responsabilit6 de v6rifier que I'installation
61ectrique du lave-vaisselle soit conforme aux normes 61ec-
triques nationales et r6gionales. Le lave-vaisselle a 6t6 con-
gu pour fonctionner avec une alimentation 61ectrique de
120V,60Hz, c.a., et doit _tre branch6 _ un circuit 61ectrique
adapt6 au lave vaisselle correctement reli6 _ la terre et pro-
t6g_ par un fusible de15 amperes. Lesconducteurs elec-
triques doivent _tre compos_s de fils en cuivre n°14 AWG
minimum ayant une r6sistance thermique minimale de 75°C
(167%).
Ce lave-vaisselle doit 6tre relier bla terre soit en le con-
nectant au support m6tallique qui est reli6 9 la terre soit
en branchant la prise du terre du lave-vaisselle _ une prise
de courant appropri6e, elle- m_me reli6e _ la terre. Ne pas
utiliser de rallonge.
Un branchement inad@quat du conducteur de raise b la
terre de I'@quipement peut mener bun risque de
d@charge @lectrique. Consultez un @lectricien qualifi@ou un
repr@sentant de I'entretien en cas de doute concernant la
raise b la terre appropri@e de I'appareil. Ne modifiez pas la
fiche fournie avec I'appareil. Si elle ne convient pas b votre
prise, faites installer une prise appropri@e par un @lectricien
qualifi_.
Risques de br_lure
Ne pas effectuer de travaux de plomberie sur un tuyau
rempli d'eau chaude. II y a des risques de blessures graves.
Seul un plombier qualifi_ peut r_aliser des manipulations
de plomberie. N'effectuer aucun travail de plomberie sur
le lave-vaisselle rant que I'arriv6e d'eau chaude n'est pas
clairement ferm_e.
Ne pas serrer trop fort le coude de 90°. Cela peut
endommager la soupape d'admission d'eau et provoquer
une fuite de I'eau.
Les temperatures n@cessaires pour souder et exsuder
risquent d'endommager la soupape d'admission d'eau du
lave-vaisselle. Si la tuyauterie a besoin d'une soudure ou
d'une exsudation, placer la source de chaleur b au moins
6 pouces (152,4 ram) de la soupape d'admission d'eau du
lave-vaisselle.
II est n6cessaire de v6rifier les normes relatives aux travaux
de plomberie pour route installation. Tout travail de
plomberie doit _tre conforme avec les normes nationales
et r6gionales.
Ces instructions sont relatives 9 une m6thode d'installation
utilisant des tuyaux d'alimentation en acier inoxydable
tress6 et des tuyaux d'eau chaude PEX. Si la tuyauterie
est en cuivre, ou tout autre mat6riau, pour I'alimentation
en eau, il fau faire appel _ un plombier qualifi6 pour une
installation appropri6e.
15

Marteau
%
J
Scie cylindrique Cl6 a tube Cl6 ajustable
Ruban a mesurer Tournevis &
lame plate Tournevis cruciforme Tournevis T-20
Pince
coupante
......... J_
Pince & d6-
nuder
L©,
Niveau a bulle
C_ble d'alimentation 61ectrique - calibre de 14 AWG minimum,
2 conducteurs, 1 mise _ la terre, conducteurs en cuivre isol6
une temp6rature nominale de 75° C ou plus.
Tuyau d'alimentation d'eau chaude - tube de cuivre de 3/8po
minimum (diametre ext6rieur) ou tuyau d'alimentation pour
lave-vaisselle en m_tal tress&
Robinet d'arr_t et raccords appropri6s pour tuyau
d'alimentation d'eau chaude ((tube de cuivre/raccord de com-
pression, ou tuyau tress6).
Un raccord de conduit ou raccord de retenue homologu@ UL
est requis si le cBblage in-situ est directement reli@au hornier.
16

(b--
e 4x13]
Q--
%
A Gicleur pour grands articles (Voir le Guide d'utilisation et
d'entretien)
B Vis pour panneau de plinthe
C Pattes de fixation
I) Vis des pattes de fixation
E Panneau de plinthe (2 pieces)
FCouvercles pour panneau de plinthe (certains modeles
uniquement)
(_ Collier _ vis (pour flexible)
H Raccord d'adaptateur d'alimentation d'eau
I Gaine de protection flexible pour fil _lectrique
JAdaptateur de tuyau de vidange en caoutchouc
K Pattes de fixation du panneau de plinthe (certains
modeles uniquement)
LPanneau de plinthe ext_rieur (3eme piece) (certains
modeles uniquement)
MR_partiteur de pouss_e pour montage lateral (montage
lat6ral alternatif uniquement)
NVis des pattes de fixation (montage lateral alternatif
uniquement)
O Botte de jonction
4x36
17

Evitez les brOlures ou les risques de secousse _lec-
trique ! S'assurer que I'alimentation d'eau et
I'alimentation _lectrique sont mises _ I'arr_t
avant toute installation ou r_paration.
REMARQUE : ce lave-vaisselle est conqu pour &tre encastr&
sous un comptoir et entre deux armoires adjacentes standard
d'une cuisine r&sidentielle.
Choisir un emplacement aussi pres que possible de I'@vier
afin que les tuyaux d'alimentation et d'@vacuation d'eau
soient facilement accessibles.
Pour un fonctionnement ad@quat du lave-vaisselle et un
aspect esth6tique agr@able, v6rifier que I'encadrement est
d'@querre et qu'il a les dimensions indiqu@es sur la figure 1
ci-dessous.
Apres avoir trouv6 acement ad@quatpour installer votre
nouveau lave-vaisselle, vous devez pr@voir les ouvertures
n6cessaires pour permettre le passage des conduites d'eau,
d'6vacuation et d'61ectricit@. Pour 6viter route interf6rence
Iors de I'installation du lave-vaisselle dans I'armoire, disposer
les ouvertures compte tenu des dimensions indiqu@es sur la
figure 3 ci-dessous.
/I I \
I I
/
E
0
REMARO_UE : si la /argeur de I'ouverture de votre lave-
vaisselle est sup&rieure B 23 _s/16po (40,8 cm), utilisez /es
m&thodes de MONTAGE PAR LE DESSUS ou LATERAL. Si
/a/argeur de I'ouverture de votre lave-vaisselle est inf&rieure
B23 lsh6 po (40,8 cm), utilisez la re&rhode de MONTAGE
LATERAL ALTERNATIE
Si le lave-vaisselle doit @treinstall6 dans un coin de la piece,
s'assurer qu'il y a un d@gagement suffisant pour ouvrir la
Voir la ficj_ure2 ci-dessous.
Evitez les risques de d_charge _lectrique et
d'incendie. Les c_bles _lectriques et les tuyaux
d'alimentation d'eau ne doivent pas entrer en
contact les uns avec les autres.
Ouvertures requises :
41/4 '' x 2" (108 x S2mm) -
4" x2" (100 x 50ram) -
11/4'' (32ram) diameter-
Passage du bottier de raccor-
dement 61ectrique compris
travers une armoire adjacente
Passagedu tuyau d'alimentation
d'eau compris vers
I'alimentation d'eau
Passagedu tuyau de vidange du
lave-vaisselle vers le raccorde-
ment de vidange
REMARO_UE : si /es raccordements d'arriv&e d'&lectricit&,
d'alimentation d'eau et de vidange se trouvent tous dans la
re&me armoire, une ouverture de 41/4 po x 2 po (108 x 52
cm) est suffisante pour recevoir /es trois.
Avant d'encastrer le lave-vaisselle dans I'armoire, retirer le
collier de serrage _ I'arriere du lave-vaisselle comme indiqu_.
Le collier de serrage peut _tre utilis_ ult6rieurement pour
maintenir le tuyau de vidange en place comme indiqu6 ci-
dessous.
................... i ........................... i............
18

Preparation de I'installation _lectrique
Evitez les risques de d_charge _lectrique et
d'incendie. Ne pas tenter d'intervenir sur un circuit
sous tension. Vous risquez autrement des blessures
graves, voire la mort. Seuls les _lectriciens qualifi_s
doivent effectuer des travaux sur I'installation _lec-
trique. Ne pas tenter d'intervenir sur le circuit _lec-
trique du lave-vaisselle b moins d'etre certain que
celui-ci est hors tension.
I_viter les risques d'incendie
V_rifier que I'installation _lectrique est correctement
r_alis_e. Seuls les _lectriciens qualifi_s doivent
effectuer des travaux sur I'installation _lectrique.
Alirnentation _lectrique
Le client a la responsabilit6 de v6rifier que I'installation
61ectrique du lave-vaisselle est conforme _ tousles codes
et ordonnances 61ectriques nationaux et Iocaux. Le lave-
vaisselle a 6t6 con6u pour fonctionner avec une alimentation
61ectrique en courant alternatif de 120volts, 60 Hz, connect6e
un circuit 61ectrique correctement mis 9 la terre, conqu
pour les lave-vaisselle, avec protection par fusible ou
disjoncteur d'une puissance de 15amperes. Lesconducteurs
d'alimentation 61ectrique doivent _tre en fil de cuivre de
calibre 14 AWG minimum _ une temperature nominale de
75°C (167°F) ou plus.
I_viter les risques d'incendie
S'assurer que les branchements _lectdques sont
bien serr_s. S'assurer que tous les branchements
_lectriques sont bien faits.
Instructions de raise _ la terre
Le lave-vaisselle dolt 6tre correctement mis 9 la terre
avant route utilisation. Cet appareil dolt _tre raccord6 9 un
systeme de c_blage en m_tal permanent mis 9 la terre ou
un conducteur de mise _ la terre du mat6riel dolt _tre utilis6
avec les conducteurs du circuit et raccord6 _ la borne de raise
la terre de I'appareil ou aufil conducteur du lave-vaisselle.
S'assurer que le lave-vaisselle est reli6 _ une masse ad6quate
conform6ment _ tous les codes Iocaux, et en I'absence de
code local, au CODE NATIONAL D'ELECTRICITC aux Etats-
Unis ou au CODE D'ELECTRICITE DU CANADA, C22.1,
derniere 6dition au Canada, ainsi qu'aux codes provinciaux,
d'6tat ou municipaux qui s'appliquent.
Caract_ristiques _lectriques du lave-vaisselle
Cet appareil dolt _tre mis _ la terre. En cas de d&fectuosit&
ou de bris, la raise _ la terre r&duira le risque de d&charge
&lectrique en offrant un chemin de moindre r&sistance
au courant &lectrique. Cet appareil est muni d'un c_ble
comprenant un conducteur de raise _ laterre de I'&quipement
et une fiche pour la raise 9 la terre. La fiche dolt _tre branch&e
dans une prise adequate install&e et mise _ la terre en
respectant routes les exigences et tousles codes Iocaux.
Raccordement _lectrique
La botte de jonction de I'alimentation &lectrique du lave-
vaisselle et la prise d&di&e doivent _tre install&es dans une
armoire accessible adjacente au lave-vaisselle (ne pas monter
la botte de jonction ni la prise derriere I'appareil). Vous aurez
besoin d'une ouverture de 41/4 po x 2 po (108 x 51 cm)
pratiqu&e dans I'armoire pour pouvoir y passer la botte de
jonction. Si I'ouverture est perc&e dans du bois, poncer le
pourtour de I'orifice. SiI'ouverture est perc&e dans du m&tal,
utiliser la gaine protectrice comprise ou route autre m&thode
approuv_e pour prot&ger le c_blage de tout dommage.
Utiliser les quatre vis comprises (ou le dispositif de fixation
appropri&) se trouvant dans le sachet contenant les pieces
pour fixer la botte de jonction en route s&curit& afin qu'elle
soit facilement accessible (voir la figure 4). L'alimentation
&lectrique peut _tre branch&e de deux faqons :
PIi!iii_i_ii_il!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_iii!
Figure 4
I1 \ ect,,....dw,t
junction box and I
three prong plug I
are included |
,.with dishwasher.//
M_thode A - Fiche _ trois broches et prise
Utiliser la fiche 9 trois broches et la bo?te de jonction
comprises pour brancher I'alimentation sur une prise
r&sidentielle d&di&e. S'assurer que la prise r&sidentielle
r&pond aux specifications relative _ I'alimentation &lectrique
ainsi qu'aux codes nationaux ou Iocaux.
Volts
120
Hertz
6O
Amperes
12
Watts
1,440
(max)
19

Pour effectuer le branchement au c_blage domestique
ou in=situ de mani_re permanente :
1. Enlever le couvercle de la botte de jonction _lectrique
du lave-vaisselle et la brancher au cordon d'alimentation
_lectrique depuis I'installation r_sidentielle (voir figure S).
Figure 5
2. Enlever 2 _ 3 po (51 _ 76 ram) de la gaine ext6rieure du
c_ble d'alimentation r6sidentiel ou in-situ comme indiqu_
sur la figure 6. Enlever :3/8_ 1/2po (10_ -13 ram) de I'isolant
de chaque fil comme indiqu_ sur la figure 6.
2"
(51mm 76mm)
Figure 6
Alimentation d'eau chaude
Le chauffe-eau doit _tre r_gl_ de fagon _ ce que I'eau qui
alimente le lave-vaisselle soit chauff_e _ une temperature
approximative de 120° F(49° C). Si la temp6rature de I'eau
est trop _lev6e, elle diminue I'efficacit_ du d_tergent. Si la
temp6rature de I'eau est trop basse, la dur6e de lavage sera
plus Iongue. La pression d'alimentation d'eau chaude doit
_tre comprise entre 15 et 145 psi (1 et 10 bars).
REMARQUE:
En cas d'utilisation d'un joint de soudure au lieu d'un rac-
cord _ compression, s'assurer que routes lessoudures sont
faites avant de brancher le tuyau d'alimentation d'eau sur
le lave-vaisselle.
S'assurer que la conduite d'eau n'est ni pli_e ni tordue
afin d'_viter route obstruction de 1'6coulement de I'eau.
Toujours utiliser les joints appropri_s pour effectuer les
raccordements sanitaires.
Avant de brancher le tuyau d'alimentation d'eau sur le
lave-vaisselle, faire couler I'eau de la conduite d'arriv6e
pendant environ 5 minutes pour 61iminer les corps
6trangers.
Une lois les raccordements termin6s, ouvrir I'alimentation
d'eau et v6rifier s'il y ades fuites.
3/8"- 1/2"
(10mm- 13mm)
3. Introduire le fil de cuivre d@nud@ou vert (raise _ la terre)
sur le conducteur de terre <<G >>_ du bloc de bornes
et visser solidement la vis du bornier (voir figure 5).
4. Introduire le fil blanc (neutre) sur la connexion en <<N >>
du bornier et visser solidement la vis du bornier.
5. Introduire le fil noir (charg6) sur la connexion en <<L >>du
bornier et visser solidement la vis du bornier.
6. V6rifier que tousles branchements @lectriques sont bien
serr6s et remonter le couvercle de la botte de jonction au
moyen des 4 vis.
Evitez ies risques de d_charge _iectrique et
d'incendie.
Pour _viter toute blessure ou tout dommage
materiel potentiel, prenez toutes les precautions
n_cessaires Iors de I'installation ou du retrait du
lave-vaisselle afin d'_viter d'endommager poten-
tiellement le cordon d'aJimentation.
i
Evitez ies br_iures ou ies risques de secousse _iec-
trique !
Ne pas tenter de travailler sur une conduite d'eau
chaude charg_e. De graves blessures pourraient
survenir. Seuls les plombiers qualifies doivent ef-
fectuer des travaux sur la tuyauterie. Ne tentez pas
d'intervenir sur la tuyauterie d'alimentation d'eau
chaude du lave-vaisselle tant que vous n'_tes pas
certain que I'alimentation d'eau chaude est couple.
Les temperatures n_cessaires pour souder et exsuder
peuvent endommager le lave-vaisselle. Si la tuyau-
terie a besoin d'une soudure ou d'une exsudation,
maintenir la source de chaleur h 6 pouces (152,4 ram)
minimum de distance du lave-vaisselle.
Robinet d'arr_t d'alimentation d'eau
Installer un robinet d'arr_t (non fourni) facilement accessible
sur le tuyau d'alimentation d'eau chaude, comme indiqu_
sur la figure 7. Toutes les connexions soud_es doivent avoir
_t6 faites avant de brancher la conduite d'eau sur le lave-
vaisselle.
2O