Bosch HBL33 User manual

Built-In
Ovens
BOSCH
Models: HBL33, HBL34, HBN34, HBL35, HBN35, HBL54, HBN54,
HBL56, HBN56, HBL57, HBL8450, HBL8650, HBL8750

Table of Contents
Safety ©0000... 0.0. ccc cece eee nent e nee eeeennenes
Important Safety Instructions
Preparation ............. 0... cece cece cece e eee eeeeeeeees
Before you Begin
Parts Included
General Information
Dimensions for 27” Wall-Mounted Units
Dimensions for 27” under the counter
Dimensions for 30” Wall-Mounted Units
Dimensions for 30” under the counter
Removing Packaging
For Convection Microwave Combination Units
Preparing Oven .. 0... eee
Microwave Combination Units Adjustment Feature
Installation ...
Tools and Parts Needed
Electrical Installation ........... 0.000 cece eee eee eee
Oven Installation
Testing Operation
Service .......
Before Calling Service
This Bosch Appliance is made by BSH
Home Appliances Corporation 5551
McFadden Ave.
Huntington Beach, CA 92649
Questions?
1-800-944-2904
www.boschappliances.com
5551 McFadden Ave.
Huntington Beach, CA 92649
We look forward to hearing from you!

Safety
() Important Safety
Instructions
READ AND SAVE THESE
INSTRUCTIONS
WARNING:
If the information in this manual is not followed exactly, fire
or shock may result causing property damage or personal
injury.
WARNING:
Do not repair or replace any part of the appliance unless
specifically recommended in the manuals. Improper
installation, service or maintenance can cause injury or
property damage. Refer to this manual for guidance. All
other servicing should be done by a qualified technician.
Appliance Handling Safety
Do not lift appliance by door handle. Remove the door for
easier handling and installation. See instructions in Use
and Care Manual.
Unit is heavy and requires at least two people or proper
equipment to move.
Hidden surfaces may have sharp edges. Use caution when
reaching behind or under appliance.
Safety Codes and Standards
This appliance complies with one or more of the following
Standards:
* UL 858, The Standard for the Safety of Household
Electric Ranges
* UL 923, The Standard for the Safety of Microwave
Cooking Appliances
* UL 507, The Standard for the Safety of Electric Fans
« ANSI Z21.1, The American National Standard for
Household Cooking Gas Appliances
* CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators
* CAN/CSA-C22.2 No. 61-M89 Household Cooking
Ranges
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
Electric Safety
Before you plug in an electrical cord, be sure all controls
are in the OFF position.
If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
Installer - show the owner the location of the circuit
breaker or fuse. Mark it for easy reference.
Important - Save these instructions for the local electrical
inspector's use.
Before installing, turn power OFF at the service panel. Lock
service panel to prevent power from being turned ON
accidentally.
Refer to data plate for more information. See "Data Plate"
under "Service" for data plate location.
Be sure your appliance is properly installed and grounded
by a qualified technician. Installation, electrical connections
and grounding must comply with all applicable codes.
Related Equipment Safety
Remove all tape and packaging before using the appliance.
Destroy the packaging after unpacking the appliance.
Never allow children to play with packaging material.
Never modify or alter the construction of the appliance. For
example, do not remove leveling legs, panels, wire covers
or anti-tip brackets/screws.
English 1

Transport
To avoid damage to the oven vent, use the transport
method shown in the picture below.
Preparation
Before
you
Begin
Parts
Included
*
Phillips
head
screws
(6)
Tools and Parts Needed
* — Phillips head screwdriver
General Information
* Measuring tape
* — Drill with bit (1/8")
Power Requirements
The outlet must be properly grounded in accordance with
all applicable codes.
English 2

Dimensions for 27”
Wall-Mounted Units
Single Oven 27”
25u2"
+ (64800)
‘li
24" _—
(10mm) (Se
a vow
(680mm) oaiane" (718mm)
| (630mm) .
pe 4 -
vont 5, 27 1/16" |
(738mm) | \C7mm)
: Z min, 494" (121mm)
max. 38" 964mm)
23776" (606mm)
“LD 22° (559mm)
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wail or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
Note:
The conduit box must be installed either above or below
the unit. If the conduit box is installed below the unit, a 2”
diameter hole or space is required between the back wall
and the right rear of the 2x4 supports.
The cabinet base must be flat and capable of supporting a
weight of at least 193 Ibs (87 kg).
Double Oven 27”
2512"
(61 om an)
26/4"
«=. (680mm)
mn, QING”
+ (630mm)
ta
518"
sta (1299mm)
(1314mm} | |
: "ee
(1264mm)
| me. min, 444 "(121mm
“| 937/8" (606mm)
we
. mm
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wall or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
Note:
The conduit box must be located above the unit to facilitate
connecting and servicing.
The cabinet base must be flat and capable of supporting a
weight of at least 361 Ibs (164 kg).
English 3

Combo Oven with Microwave and
Warming Drawer 27”
2541/2"
« (648mm)
24 ee
(610mm) P
Me,
bay
2634" ~
~ (680mm) ——
“| gatane"
<<“ (630mm)
ae
=
(1543mm)
5985/8"
(1514mm)
a oe
min. 434° (121mm
max.1298(315mm)
_—
_ 2378" (606mm)
22" (5 9 x (59mm)
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wall or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
The cabinet base must be flat and capable of supporting a
weight of at least 369 Ibs (167 kg).
English 4
2/7” Under-the-counter units
24" [> (418mm)
(610mm)
28/4" min. 3” 20"
(718mm) (76mm) _ (508mm)
263/4"
(680mm)
2413/16" (648mm)
(630mm) 43/4"
4 (121mm)
- 27 1/16”
291/16" (687mm)
(738mm) 2
237/8"(606mm)
L- 23"(550mm)
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wall or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
The cabinet base must be flat and capable of supporting a
weight of at least 193 Ibs (87 kg).
This Built -In Oven can be installed below any Bosch cook
top as long as there is no contact between the bottom of
the cook top and the top of the oven, except for the Bosch
Induction cooktop, where the gap must be of at least 1 inch.

27” Units - under electric cooktop
(102mm)
hk 63/4" _|
(72mm
Fitting/4
Conduit
36"
(914mm)
)
7 "
4/4 Y TOE KICK
q {121mm}
Note: Dimensions based on standard countertop height (36" with 43/4" toe kick
including base plate).
The built-in oven can be installed below the electric cooktop as long as there is
no contact between the bottom of the cooktop and the top of the oven.
27” Units - under gas cooktop
63/4"_]
(172mm)
Gas 4
Connection
36"
(914mm)
51/16" 313/16"
(144mm) (97mm)
43/16"
(106mm)
(718mm)
COUNTERTOP
a 43/4"
v ¥ (121mm)
247/16"
{621mm} 27 ie" 291/16"
(687mm) (738mm)
TOE KICK
Note: Dimensions based on standard countertop height (36" with 43/4" toe kick
including base plate).
The built-in oven can be installed below the gas cooktop as long as there is no
contact between the bottom of the cooktop and the top of the oven.
27” Units - under induction cooktop
A 63/4"
(172mm)
Fitting/
Conduit
36"
(914mm)
Heat shield: Self positioning — 2 3/s" length,
Minimum required air clearance: 1° (26mm)
4" 31/3"
(02mm) {79mm}
43/6"
27/16"
{687 mm)
281/4"
(718mm)
COUNTERTOP
291/16"
(738mm)
rar
G2imm)
ZY TOE KICK
Note: Dimensions based on standard countertop height (36” with 43/4" toe kick
including base plate).
The built-in oven can be installed below the induction cooktop as jong as there
is an air clearance of 1" between the bottom of the cooktop and the top of the oven.
English 5

Dimensions for 30”
Wall-Mounted Units
Single Oven 30”
2612"
l (724mm)
2a"
(61 ommy << >
Pot anaag
~ 2ga/a" osse'l :
a “ef Tt
“boy 27 1/16” | :
726mm) | jGo7mm)
it min, 494° (121mm)
max. 38" (964mm)
2378" (606mm)
Le 22” (559mm)
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wail or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
Note:
The conduit box must be installed either above or below
the unit. If the conduit box is installed below the unit, a 2”
diameter hole or space is required between the back wall
and the right rear of the 2x4 supports.
The cabinet base must be flat and capable of supporting a
weight of at least 212 Ibs (96 kg).
English 6
Double Oven 30”
212"
s-(724mm)
24° —
(610mm).
|,
|
“ :
vos
|
~ (755mm)
518"
sta
(1299mm)
(1314mm)
a
(1264mm)
| min. 44° (121mm.
ol. max.170/4"(43emmn)-
23778" (606mm)
awe )
a
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wall or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
Note:
The conduit box must be located above the unit to facilitate
connecting and servicing.
The cabinet base must be flat and capable of supporting a
weight of at least 390 Ibs (177 kg).

Combo Oven with Microwave 30”
age"
~~ (724mm)
(610mm). Ne 4 |
pow" spon
r (755m)
tm, QING"
<<“ (706mm)
on age
(1267mm)
(1229mm) r
| min, 484" (izimm)
ae
2a7ie" (606mm)
we
a
2 (559mm)
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wail or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
Note:
The conduit box must be located above the unit to facilitate
connecting and servicing.
The cabinet base must be flat and capable of supporting a
weight of at least 310 Ibs (141 kg).
Combo Oven with Microwave and
Warming Drawer 30”
2a12"
par 724mm)
(610mm) a
aaa"
~~ (755mm)
“| -g71ae"
<*> (706mm)
603/4"
(1543mm)
595/08"
(1614mm)
min, 43/4" (412 —
max.1299(315mm)
ty
237/8" (606mm)
22° (559mm)
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wall or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
Note:
The conduit box must be located above the unit to facilitate
connecting and servicing.
The cabinet base must be flat and capable of supporting a
weight of at least 429 Ibs (195 kg).
English 7

Dimensions for 30” Under-the-counter-
Units
46112"
24" t- {419mm}
(610mm)
36
(245mm)
28/4"
(718mm)
min. 3" 20"
(76mm) (508mm)
2934"
Hae
“orm | 27136" (724mm)
{706rmm)
43/4"
(421mm)
27 1/16”
(687mm)
237/8"(606mm)
L 23" (559mm)
It is good practice, when oven is installed at the end of a
cabinet run, adjacent to a perpendicular wall or cabinet
door, to allow at least 1/4” space between the side of the
oven and the wall/door.
For oven support, install 2x4’s extending front to back flush
with the bottom and the side of the opening. The supporting
base must be well secured to the floor/cabinet and level.
This Built -In Oven can be installed below any Bosch cook
top as long as there is no contact between the bottom of
the cook top and the top of the oven, except for the Bosch
Induction cooktop, where the gap must be of at least 1 inch.
English 8
30” Units - under electric cooktop
415/16" 4" 43/6"
(125mm) (102mm) (106mm) COUNTERTOP
63/4" a3 “y6mnm)
172mm :
Fitting / gee 4
Conde Fe psume A
3/16" D>
113/16" (4mm}
36" (47mm) OVEN 281/4"
(914mm) (718mm) 291/16"
247/16 (738mm)
(621mm) n
271/16
(687 mm)
A 43/4"
y (121mm) TOE KICK
Note: Dimensions based on standard countertop height (36” with 43/4" toe kick
including base plate}.
The built-in oven can be installed below the electric cooktop as long as there is
no contact between the bottom of the cooktop and the top of the oven.
30” Units - under gas cooktop
51/6" 313/16" 43/16"
(144mm) (97mm) — (106mm) COUNTERTOP
A 63/4" 3 “7emm)
(172mm)
Gas 7
Connection
36" bamm) OVEN 281/4"
(914mm) (718mm)
247/16"
{621mm} 1 n
27 "16" 20 Ne
(687mm) mm
7 m Z ,
43/4 TOE KICK
(121mm)
Note: Dimensions based on standard countertop height (36" with 42/4” toe kick
including base plate).
The built-in oven can be installed below the gas cooktop as long as there is no
contact between the bottom of the cooktop and the top of the oven.