Bosch HWD Series User manual

Warming Drawer Model: HWD BOSCH
Invented for life

Important Safety Instructions ................................... 1
Installation ................................................. 1
Before You Begin ...................................................... 1
Tools and Parts Needed ........................................................ 1
Parts Included ................................................................ 1
Warming Drawer Dimensions .................................................... 1
Cabinet Cutout Dimensions ...................................................... 2
Custom Drawer Front Dimensions (Optional) ........................................ 2
Power Requirements and Grounding .............................................. 3
Installation Procedure ................................................... 3
Prepare Cabinet Cutout ......................................................... 3
Install Support Brackets ......................................................... 3
Install Warming Drawer ......................................................... 3
Attach Custom Drawer Front (Optional) ............................................ 3
Connect Electric .............................................................. 4
Test the Installation ............................................................ 4
Service .................................................... 4
Questions?
1-800-944-2904
www.boschappliances.com
5551 McFadden Ave.
Huntington Beach, CA 92649
We look forward to hearing from you!

Important Safety Instructions
Save these Instructions
Be sure your appliance is properly installed and grounded by a qualified
technician in accordance with the National Electrical Code ANSI/NFPA No. 7lat-
est edition (or the Canadian Electric Code) and local electrical code requirements.
Important: Local codes vary. Installation, electrical connections and grounding
must comply with all applicable codes.
Never use your appliance for warming or heating a room.
Children should not be left alone or unattended in area where appliance is in use.
Do not allow children to sit or stand on any part of the appliance.
Do not repair or replace any part of the appliance unless specifically recom-
mended in the manual. All other servicing should be referred to a qualified techni-
cian.
Flammable materials should not be stored in the appliance.
Installation
Before You Begin
Tools and Parts Needed
Parts Included
• Saw
• Phillips Head Screwdriver
• Measuring Tape
• Screws, 8 x 5/8" (5.9mm) (8)
• Support Brackets (2)Warming Drawer Dimensions
English 1

Figure1 WarmingDrawerOverallDimensions
Table1 WarmingDrawerOverallDimensions
CabinetCutoutDimensions
i i/!iiii!!!! !!!!!!!!!!i
A 11 1/4" (285.8mm) 11 1/4" (285.8 mm)
B 26 5/8" (676.3 mm) 29 1/4" (743 mm)
C 22 1/4" (565.2 mm) 22 1/4" (565.2 mm)
D 20 1/2" (520.7 mm) 20 1/4" (514.4 mm)
Instructions are based on standard American cabinets 36" (914 mm) high x 24"
(609 mm) deep with a 25" 635 mm) countertop. If using non-standard cabinets, to
alter dimensions accordingly.
Cabinet opening bottom must be able to support 90 pounds (41 kg). Otherwise,
use the support brackets provided. If using the brackets, the sidewalls must sup-
port 45 pounds (20.5 kg) each.
Figure 2: Cabinet Cutout Dimensions
1/2" (12 7mm)
__cFrame Overlaps
abinet
(12 7ram)
Allow 3-1/2" (88.9mm) in front
1-1/2" (38 1ram) Min. to _for drawer hand{e clearance
F opening ( see 'terrl 4)_ ?_i - c _
I
I
U
_ H_ D Frame
AOverlaps
Cabinet
Wall
Receptacle
Brackets
Table 2: Cabinet Cutout Dimensions
A 25 3/4" (654.1 mm) 25 3/4" (654.1 mm)
B 10" (254 mm) 10" (254 mm)
English 2

Custom Drawer Front Dimensions
(Optional)
Table 2: Cabinet Cutout Dimensions
C 22 1/4" (565.2 mm) 22 1/4" (565.2 mm)
D 7/16" (11.1 mm) 1 3/4" (44.5 mm)
Build custom drawer front to the dimensions specified in Table 3 on page 3 and-
Table 4 on page 3 below. All four edges must be finished. If using wood, the back
must be sealed to prevent moisture damage.
Figure 3: Custom Drawer Front Dimensions
I A
I G
_ ilot Holes JJ_J_J+
1/2" (12.7 mm)
Diameter Hote
__ D I__
B
Table 3 Custom Drawer Front Dimensions
Power Requirements and
Grounding
Installation Procedure
1) Prepare Cabinet Cutout
2) Install Support Brackets
A 26 5/8" (676.3 mm) 29 1/4" (743 mm)
B 11 1/4' (285.8 mm) 11 1/4" (285.8 mm)
C 1 1/4" (31.6 mm) 1 1/4" (31.6 mm)
D 1 1/4" (31.6 mm) 2 9/16" (65.1 mm)
E 2 3/4" (69.9 mm) 2 13/16" (71.5 mm)
F 2 1/4" (57.2 mm) 2 1/4" (57.2 mm)
G 21 1/16" (535 mm) 23 5/8" (600.1 mm)
Circuit Specifications: 120 V, 15 A, 60 Hz. The outlet must be properly grounded
in accordance with all applicable codes.
Prepare cabinet cutout and install electrical connection according to the dimen-
sions in Figure 2 on page 2 and Table 2 on page 2.
When the opening does not have a bottom, or the bottom is not strong enough to
support the drawer, install the two support brackets included. Attach brackets 8"
(203.2 mm) from the front wall of the cabinet. Make sure that the brackets are
level before installing screws through screw holes into cabinet sidewalls (two
screws on each side). Note: Cabinet sidewalls must be strong enough to support
45 pounds (20.5 kg) each. See "Cabinet Cutout Dimensions" on page 2 for further
details.
English 3

3) Install Warming Drawer
4) Attach Custom Drawer Front
(Optional)
7) Connect Electric
8) Test the Installation
Service
Slide warming drawer assembly into cutout and over support brackets (if applica-
ble) until it is flush with cabinet. Secure through four screw holes in front frame
(Drill pilot holes in cabinet first if necessary.).
CAUTION: Use care when handling glass panel to avoid breaking. Broken glass
could cause injury.
1) Prepare custom drawer front as explained above.
2) Remove drawer from warming drawer frame (See Use and Care Manual for
instructions).
3) Remove two screws from backside of drawer front. Set handle and screws
aside.
4) Remove signal light viewer and retainer clip from glass panel and set aside.
Discard glass panel (Note: stainless steel models do not have a glass panel).
5) Install the signal light viewer and the retainer clip in the custom drawer front.
6) Attach drawer front with two screws. Attach handle as well if desired.
Insert plug into three-prong, grounded outlet. See "Power Requirements and
Grounding", above for electrical specifications.
Turn the warming drawer on. Signal light turns on immediately. Wait five minutes
and then place palm on drawer bottom. It should be warm to the touch.
If the warming drawer elements or signal light do not turn on, check the power
source to see if the circuit breaker is tripped.
Check the Use and Care Manual for other troubleshooting techniques.
If problems persist, contact Service (see contact information at the front of this
manual).
English 4

YOURLIFE,OURINSPIRATION,
5551 McFadden Avenue, Huntington Beach_ CA 92649 • 800-944-2904 ° www.boschapptiances.com
9000060282 (ECO# 5V03FT) • 10006 Rev A •04/05 © BSH Home Appliances Corporation 2005 • Litho U.S.A.