Bosch GWH 715 ES Instructions for use

Applications manual
For tankless and point-of-use water heaters

2| Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 3
Table of Contents
1 Introduction 4
2 Bosch Water Heating Models 4
2.1 Sizing tankless water heaters 4
2.2 Bosch GWH 715 ES 6
2.3 Bosch GWH C 800 ES 7
2.4 Outdoor Installation for GWH 715 ES and GWH C 800 ES 8
2.5 Bosch GWH 345 ESR 9
2.6 Bosch GWH 450 ESR 10
2.7 Bosch GWH 425 EF 11
2.8 Bosch GWH 425 HN 12
2.9 Bosch GWH 425 PN 13
2.10 Bosch GWH 260 PN 14
2.11 Powerstream Pro RP17PT, RP27PT 15
2.12 Powerstream Pro RP1P, RP2P, RP3P, RP7P, RP9P, RP12PT 16
2.13 Ariston Pro GL2.5Ti, GL4Ti, GL8Ti 17
3 Domestic Water Heating Applications 18
3.1 Point-of-use applications 18
3.2 Whole house applications 22
4 High Volume Potable Water Heating 26
4.1 Parallel unit applications 26
4.2 Cascade unit applications 28
4.3 External storage tank loading applications 29
5 Open Loop Space Heating 32
5.1 External storage tank 32
5.2 Indirect tank applications 42
6 Maintenance Drawings 44
6.1 Descaling procedure 44
6.1 Descaling procedure diagram 45

4| Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
1 Introduction
The Bosch Applications Manual is intended to present some of the
most common applications of the Bosch line of tankless and point of
use water heaters. Application drawings are shown with both piping
and corresponding electrical schematics where applicable. Auxiliary
equipment depicted does not necessarily represent any one
manufacturer or specific model number. There are a wide variety of
techniques, practices and piping strategies possible when installing
water heating appliances. It is the responsibility of the installing
contractor to determine the most suitable arrangement for the
application.
Although this manual covers many common applications for our
products, system possibilities are virtually endless. Should you
encounter an application that is not covered in this manual or have
any questions regarding any of its content, we encourage you to
contact your local sales representative or us directly at Bosch Water
Heating.
This is not a substitute for any of the product’s installation manuals.
All specifications subject to change.
Installation must conform with local codes or, in the absence of
local codes, the National Fuel Gas Code ANSI Z 223.1/NFPA 54.
In Canada: Installation must conform with CGA B149.(1,2) INSTAL-
LATION CODES and/or local installation codes.
2 Bosch Water Heating Models
This section describes the water heaters available from Bosch
Thermotechnology Corporation. The information given in each
section provides a general overview to the specifications of that
particular model. More detailed information is contained in the
installation manuals. Download these manuals at www.BoschPro.
com.
2.1 Sizing tankless water heaters
Definitions
Major applications (2 GPM or more): Washing machine, bath tub,
shower nozzle
Minor applications(1.5 GPM or less): Low flow shower head,
bathroom sink, kitchen sink
Rule of thumb sizing
The tables below provide a general rule of thumb when sizing for
most residential applications. For commercial applications or for a
more detailed sizing method, use the instructions below in
conjunction with the charts on the next page.
Sizing by Chart
Measure the flow rates at each fixture that will be used
simultaneously and add them together. If only one application will
be used at a time measure each fixture and use the maximum flow
rate observed.
Rule of Thumb Sizing
Model Number Number of Major
Applications
Number of Minor
Applications
GWH 715 ES 2 0
GWH C 800 ES 2 1
GWH 425 HN/PN/EF 1 1
GWH 425 HN/PN/EF 0 2
GWH 260 PN 1 0
RP17PT 1 0
RP27PT 1 1
Using a known volume container, record several fill times. Per-
form the calculation below to determine the flow rate (a one
gallon fill time of 30 seconds is 2.0 gallons per minute (GPM):
Flow rate (GPM) = Volume (gallons)
Fill time (sec)
sec
min
60
x
Using a thermometer, measure the incoming water temperature.
Subtract this temperature from the desired hot water temperature
to get the degree rise. So, if the desired hot water temperature is
120F and incoming temperature is 55F, the desired degree rise is
65F.
This example requires a flow rate of 2.0 GPM at a 65˚F rise. Refer
to the graphs on the following page. Since the demand is above
the GWH 260 PN capacity, this application would require a GWH
425 HN/PN/EF gas tankless water heater. The electrical model
used for this application would be the RP27PT electric tankless
water heater.

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 5
0
1
2
3
4
5
6
7
8
GWH 425 PN/HN/EF
4
GWH 425
4
GWH 260 PN/HN
2
10 20 30 40 50 60 70 80 90
Degree rise (°F)
GPM
G
as App
l
iance Sizing C
h
ar
t
GWH 715 ES
7
GWH C 800 ES
C
GWH C 8
C
0
.
0
0
.
5
1.
0
1.
5
2
.
0
2
.
5
3
.
0
3
.
5
4.
0
RP27PT
P
10 20 30 40 50 60 70 80 90
Degree rise (°F)
G
P
M
El
ectric App
l
iance Sizing C
h
art
RP17PT
P
RP17PT
P
RP12PT
P
RP12PT
P
RP1P
P
P
R
P7
P
RP9P
P
9P
RP3P
3
Note
:Maximum flow rates de
p
endant on site condition
s

6| Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
2.2 Bosch GWH 715 ES
Features:
Electronic ignition and built in power vent
82% thermal efficiency
Vents vertically or horizontally with 3" or 4" stainless steel
(AL29-4C)
Direct vent room-sealed combustion
Computerized temperature control — ensures temperature stability
Model GWH 715 ES N for natural gas (NG) supply
Model GWH 715 ES L for liquid propane (LP) supply
15-year warranty on heat exchanger
GWH 715 ES Technical Specifications
Gas input Natural Gas: 19,900 - 199,000 BTU
LP Gas: 19,900 - 199,000 BTU
Minimum flow to activate 0.65 gallons per minute (gpm)
Flow rates 45˚F rise @ 7.2 gpm
55˚F rise @ 5.9 gpm
65˚F rise @ 5.0 gpm
77˚F rise @ 4.2 gpm
90˚F rise @ 3.6 gpm
Thermal Efficiency NG: 82% LP: 82%
Dimensions 30½" h x 17⅞" w x 11¼" d
Weight 67 lbs.
Modulating gas valve yes
Ignition Electronic
Accessories Outdoor kit (PTOK)
Wireless Remote (TSTAT2)
Tankless Link Cascading Kit (TLINK)
Freeze Prevention Kit (8700400022)
Water Filter Kit (8703305356)
GWH 715 ES Installation Specifications
Gas connection ¾" Male NPT
Water connections ¾" Male NPT
NG gas pressure Minimum: 4" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 9" W.C.
Maximum: 14" W.C.
Water pressure
(Static)
Minimum: 30 PSI
Minimum well pressure: 40 PSI
Maximum: 150 PSI
Electrical supply 120VAC - plugs in
Venting 3" or 4" stainless steel (AL29-4C)
direct vent
room-sealed combustion
GWH 715 ES Installation Clearances
Top (A) 12"
Front (B) 1"
Back 0"
Sides 1"
Floor (C) 12"
3ft minimum
distance
3ft minimum
distance
Fig. 1 Venting configurations
Installation guidelines:
Venting:
Must be 3" or 4" AL29-4C sealed stainless steel vent pipe.
Slope horizontal runs up to termination ¼" per foot. The last
horizontal section of exhaust vent pipe between last elbow and
termination must slope down to the termination ¼" per foot.
Do not combination vent with any other appliance.
Install condensate drain where applicable.
See manual for vent terminator clearances.
Gas piping:
Heater will not function properly without adequate supply gas
pressure.
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable
drain.
Minimum piping diameter is ¾".
Do not solder directly to the bottom of the unit.
Use unions to facilitate easy future maintenance.
Use full port ball valves for isolation valves.
Partially fill condensate drain tube loop (where applicable) with
water prior to start up.

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 7
2.3 Bosch GWH C 800 ES
Features:
Electronic ignition and built in power vent
Condensing technology with 92% thermal efficiency
Vents vertically or horizontally with 3" or 4" PVC, CPVC or ABS
(Schedule 40) vent pipe.
Direct vent room-sealed combustion with concentric venting
option
Computerized temperature control — ensures temperature stability
Model GWH C 800 ES N for natural gas (NG) supply
Model GWH C 800 ES L for liquid propane (LP) supply
15-year warranty on heat exchanger
GWH C 800 ES Technical Specifications
Gas input Natural Gas: 19,900 - 199,000 BTU
LP Gas: 19,900 - 199,000 BTU
Minimum flow to activate 0.65 gallons per minute (gpm)
Flow rates 45˚F rise @ 8.0 gpm
55˚F rise @ 6.4 gpm
65˚F rise @ 5.5 gpm
77˚F rise @ 4.6 gpm
90˚F rise @ 3.9 gpm
Thermal Efficiency NG: 92% LP: 92%
Dimensions 30½" h x 17⅞" w x 11¼" d
Weight 74 lbs.
Modulating gas valve yes
Ignition Electronic
Accessories Outdoor kit (PTOK)
Wireless Remote (TSTAT2)
Tankless Link Cascading Kit (TLINK)
Freeze Prevention Kit (8700400022)
Water Filter Kit (8703305356)
Concentric Termination Kit
(BWH60L46)
GWH C 800 ES Installation Specifications
Gas connection ¾" Male NPT
Water connections ¾" Male NPT
NG gas pressure Minimum: 4" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 9" W.C.
Maximum: 14" W.C.
Water pressure
(Static)
Minimum: 30 PSI
Minimum well pressure: 40 PSI
Maximum: 150 PSI
Electrical supply 120VAC - plugs in
Venting 3" or 4" PVC, CPVC, or ABS
(Schedule 40) direct vent sealed
combustion
GWH C 800 ES Installation Clearances
Top (A) 12"
Front (B) 1"
Back 0"
Sides 1"
Floor (C) 12"
INTAKE
EXHAUST
COMBUSTION
AIR
MAINTAIN 12 IN.
(18IN. FOR CANADA)
MINIMUM CLEARANCE
ABOVE
HIGHEST ANTICIPATED
SNOW LEVEL.
MAXIMUM OF 24 IN.
ABOVE ROOF.
VENT
ROOF BOOT/
FLASHING (FIELD
SUPPLIED
DRAIN TEE
INTAKE
EXHAUST
MINIMUM
1”
VENT
COMBUSTION
AIR
DRAIN TEE
Fig. 1 Venting configurations
Installation guidelines:
Venting:
Must be 3" or 4" PVC, CPVC or ABS (Schedule 40) vent pipe.
Attach drain for internal condensate siphon and dispose of
according to local codes.
Do not combination vent with any other appliance.
Install an external condensate drain where applicable.
See manual for vent terminator clearances.
Gas piping:
Heater will not function properly without adequate supply gas
pressure.
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable
drain.
Minimum piping diameter is ¾".
Do not solder directly to the bottom of the unit.
Use unions to facilitate easy future maintenance.
Use full port ball valves for isolation valves.
Partially fill condensate drain tube loop (where applicable)

8| Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
2.4 Outdoor Installation for GWH 715 ES,
and GWH C 800 ES
Outdoor Kit (PTOK) installation:
The installation of this outdoor kit (PTOK) is required when
installing either of the above appliances outdoors
Outdoor cap easily retrofits to these indoor models
Outdoor kit comes with Freeze Prevention which must be installed
Exterior water piping should be protected if freezing conditions
could exist
Not for use in areas routinely exposed to freezing temperatures
Minimum clearances:
Ref. Description Min.
distances
ADirectly below or adjacent to
an opening; operable
windows, doors and any fresh
air openings
≥4 ft
B
C
D From any adjacent wall ≥4 ft
EBelow a gutter, sanitary
pipework, eaves or overhang ≥3 ft
F Above ground ≥1 ft
GFrom a gas meter or gas
regulator
≥5 ft
Outdoor Installation Clearances
Source: NFPA 54 National Fuel Gas Code
ANSI Z223.1
Installation on wood siding
Installation on vinyl siding:

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 9
2.6 Bosch GWH 345 ESR
Features:
Specifically designed for recirculating applications
Electronic ignition and built in power vent
GWH 345 ESR thermal efficiency of 82%
Vents vertically or horizontally with 3" stainless steel (AL29-4C)
Direct vent room-sealed combustion
Computerized temperature control — ensures temperature
stability
Model GWH 345 ESR N for natural gas (NG) supply
Model GWH 345 ESR L for liquid propane (LP) supply
10-year warranty on heat exchanger
GWH 345 ESR Technical Specifications
Gas input GWH 345 ESR: 32,000 - 95,000 Btu/h
Maximum flow rates GWH 345 ESR: 3.5gpm @ 45°F rise
Thermal Efficiency 82%
Dimensions 27.5" h x 15.75" w x 11.75" d
Weight 47 lbs.
Modulating gas valve yes
Ignition Electronic
GWH 345 ESR Installation Specifications
Gas connection ¾" Male NPT
Water connections ¾" Male NPT
NG gas pressure Minimum: 5.5" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 11" W.C.
Maximum: 14" W.C.
Electrical supply 120VAC - plugs in
Venting 3" stainless steel (AL29-4C)
direct vent
room-sealed combustion
GWH 450 ESR Installation Clearances
Top (A) 12"
Front (B) 1"
Back 0"
Sides 1"
Floor (C) 12"
Fig. 1 Venting configurations
Installation guidelines:
Venting:
Must be 3" or 4" AL29-4C sealed stainless steel vent pipe.
Slope horizontal runs up to termination ¼" per foot. The
horizontal section between last elbow and termination must slope
down to the termination ¼" per foot.
Do not combination vent with any other appliance.
Always install an external condensate drain except when
terminating horizontally with less than 3 feet of pipe.
See manual for vent terminator clearances.
Gas piping:
Heater will not function properly without adequate supply gas
pressure.
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable
drain.
Minimum piping diameter is ¾".
Do not solder directly to the bottom of the unit.
Use unions to facilitate easy future maintenance.
Use full port ball valves for isolation valves.
Partially fill condensate drain tube loop with water prior
to start up.

10 | Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
2.6 Bosch GWH 450 ESR
Features:
Specifically designed for recirculating applications
Electronic ignition and built in power vent
GWH 450 ESR thermal efficiency of 81%
Vents vertically or horizontally with 3" stainless steel (AL29-4C)
Direct vent room-sealed combustion
Computerized temperature control — ensures temperature
stability
Model GWH 450 ESR N for natural gas (NG) supply
Model GWH 450 ESR L for liquid propane (LP) supply
10-year warranty on heat exchanger
GWH 450 ESR Technical Specifications
Gas input GWH 450 ESR: 45,000 - 120,000 Btu/h
Maximum flow rates GWH 450 ESR: 4.5gpm @ 45°F rise
Thermal Efficiency 81%
Dimensions 27.5" h x 15.75" w x 11.75" d
Weight 47 lbs.
Modulating gas valve yes
Ignition Electronic
GWH 450 ESR Installation Specifications
Gas connection ¾" Male NPT
Water connections ¾" Male NPT
NG gas pressure Minimum: 5.5" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 11" W.C.
Maximum: 14" W.C.
Electrical supply 120VAC - plugs in
Venting 3" stainless steel (AL29-4C)
direct vent
room-sealed combustion
GWH 450 ESR Installation Clearances
Top (A) 12"
Front (B) 1"
Back 0"
Sides 1"
Floor (C) 12"
Fig. 1 Venting configurations
Installation guidelines:
Venting:
Must be 3" or 4" AL29-4C sealed stainless steel vent pipe.
Slope horizontal runs up to termination ¼" per foot. The
horizontal section between last elbow and termination must slope
down to the termination ¼" per foot.
Do not combination vent with any other appliance.
Always install an external condensate drain except when termi-
nating horizontally with less than 3 feet of pipe.
See manual for vent terminator clearances.
Gas piping:
Heater will not function properly without adequate supply gas
pressure.
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable
drain.
Minimum piping diameter is ¾".
Do not solder directly to the bottom of the unit.
Use unions to facilitate easy future maintenance.
Use full port ball valves for isolation valves.
Partially fill condensate drain tube loop with water prior
to start up.

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 11
2.7 Bosch GWH 425 EF
Features:
Electronic ignition and built in power vent
Thermal efficiency of 82%
Vents with 4" stainless steel or galvanized vent pipe
Specifically designed for horizontal vent terminations
Modulating gas valve — ensures temperature
stability
Model GWH 425 EF N for natural gas (NG) supply
Model GWH 425 EF L for liquid propane (LP) supply
15-year warranty on heat exchanger
GWH 425 EF Technical Specifications
Gas input Natural Gas: 28,000 - 130,000 Btu/h
LP Gas: 28,000- 125,000 Btu/h
Minimum flow to
activate
0.5 gallons per minute (GPM)
Maximum flow rates 4.6 gpm @ 45°F rise
Thermal Efficiency NG: 80% LP: 82%
Dimensions 29.75" h x 18.25" w x 8.75" d
Weight 44 lbs.
Modulating gas valve yes
Ignition Electronic
GWH 425 EF Installation Specifications
Gas connection ½" Male NPT
Water connections ½" Male NPT
NG gas pressure Minimum: 7" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 11" W.C.
Maximum: 14" W.C.
Electrical supply 120VAC - plugs in
Venting 4" stainless steel (AL29-4C)
or 26 gauge galvanized
GWH 425 EF Installation Clearances
Top (A) 12"
Front (B) 4"
Back 0"
Sides 4"
Floor (C) 12"
Fig. 1 Venting configurations
Installation guidelines:
Venting:
4" AL29-4C sealed stainless steel or 26 gauge galvanized vent
pipe.
Slope horizontal runs up to termination ¼" per foot.
Do not combination vent with any other appliance.
See manual for vent terminator clearances.
Gas piping:
Heater will not function properly without adequate supply gas
pressure.
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable
drain.
Minimum piping diameter is ½".
Do not solder directly to connections on the bottom of the unit.
Use full port ball valves for isolation valves.

12 | Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
2.8 Bosch GWH 425 HN
Features:
Hydro-generated ignition
80% thermal efficiency
Endless hot water for one major application at a time
Venting: 5" double wall B-vent — natural draft
Modulating gas valve — constant temperature at varying flow rates
Model GWH 425 HN N for natural gas (NG) supply
Model GWH 425 HN L for liquid propane (LP) supply
15-year warranty on heat exchanger
GWH 425 HN Technical Specifications
Gas input Natural Gas: 30,735 - 117,000 BTU
LP Gas: 30,735 - 117,000 BTU
Minimum flow to activate 0.6 gallons per minute (gpm)
Flow rates 45˚F rise @ 4.2 gpm
55˚F rise @ 3.4 gpm
65˚F rise @ 2.9 gpm
77˚F rise @ 2.4 gpm
90˚F rise @ 2.1 gpm
Thermal Efficiency NG: 80% LP: 80%
Dimensions 25.75" h x 16.75" w x 8.5" d
Weight 33 lbs.
Modulating gas valve yes
Ignition Hydro-generated
Accessories Horizontal vent kit (AQ4) - power
vent kit for horizontal venting
GWH 425 HN Installation Specifications
Gas connection ¾" Male NPT
Water connections ¾" Male NPT
NG gas pressure Minimum: 7" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 11" W.C.
Maximum: 14" W.C.
Water pressure
(Static)
Minimum: 30 PSI
Minimum well pressure: 40 PSI
Maximum: 150 PSI
Electrical supply 120VAC - plugs in
Vertical venting 5" minimum diameter - natural
draft
Horizontal venting AQ4 horizontal vent kit required
for horizontal terminations
GWH 425 HN Installation Clearances
Top (A) 12"
Front (B) 4"
Back 0"
Sides 4"
Floor (C) 12"
LIS TED VENT C AP
MINIMUM 6
FEET (1.8M)
LIS TED G AS VENT
ESTABLISH A ONE
FOOT RISE BEFORE
ANY ELBOWS
Fig. 2 Venting configuration
Installation guidelines:
Venting:
5" minimum diameter — do not reduce vent size
Refer to installation manual for vent material options
Do not combination vent with any power vented appliances
Establish a one-foot rise before any elbows
Minimum vent height - 6 feet
 Horizontal sections must slope upwards at least ¼" for every foot
of the horizontal length and be properly supported
Gas piping:
Heater will not function properly without adequate supply gas
pressure
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable drain
Minimum piping diameter is ¾"
Do not solder directly to connections on the bottom of the unit
Use full port ball valves for isolation valves

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 13
2.9 Bosch GWH 425 PN
Features:
Standing pilot ignition
78% thermal efficiency
Endless hot water for one major application at a time
Modulating gas valve — constant temperature at varying flow rates
Model GWH 425 PN N for natural gas (NG) supply
Model GWH 425 PN L for liquid propane (LP) supply
15-year warranty on heat exchanger
GWH 425 PN Technical Specifications
Power input Natural Gas: 31,000 - 117,000 BTU
LP Gas: 31,000 - 117,000 BTU
Minimum flow to activate 0.6 gallons per minute (gpm)
Flow rates 45˚F rise @ 4.2 gpm
55˚F rise @ 3.4 gpm
65˚F rise @ 2.9 gpm
77˚F rise @ 2.4 gpm
90˚F rise @ 2.1 gpm
Thermal Efficiency NG: 78% LP: 78%
Dimensions 25.75" h x 16.75" w x 8.5" d
Weight 33 lbs.
Modulating gas valve yes
Ignition Standing pilot
Accessories Horizontal vent kit (AQ4) - power
vent kit for horizontal venting
GWH 425 PN Installation Specifications
Gas connection ¾" Male NPT
Water connections ¾" Male NPT
NG gas pressure Minimum: 7" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 11" W.C.
Maximum: 14" W.C.
Water pressure Minimum: 30 PSI
Maximum: 150 PSI
Electrical supply 120VAC - plugs in
Vertical venting 5" minimum diameter - natural
draft
Horizontal venting AQ4 horizontal vent kit required
for horizontal terminations
GWH 425 PN Installation Clearances
Top (A) 12"
Front (B) 4"
Back 0"
Sides 4"
Floor (C) 12"
LIS TED VENT C AP
MINIMUM 6
FEET (1.8M)
LIS TED G AS VENT
ESTABLISH A ONE
FOOT RISE BEFORE
ANY ELBOWS
Fig. 4 Venting configuration
Installation guidelines:
Venting:
5" minimum diameter — do not reduce vent size.
Refer to installation manual for vent material options
Do not combination vent with any power vented appliances.
Establish a one-foot rise before any elbows
Minimum vent height - 6 feet.
Horizontal sections must slope upwards at least ¼" for every foot
of the horizontal length and be properly supported.
Gas piping:
Heater will not function properly without adequate supply gas
pressure.
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable
drain.
Minimum piping diameter is ¾".
Do not solder directly to the bottom of the unit.
Use full port ball valves for isolation valves.

14 | Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
2.10 Bosch GWH 260 PN
Features:
Standing pilot ignition
78% thermal efficiency
Mounts on wall for easy installation
Venting: 4" double wall B-vent — natural draft
Modulating gas valve — constant temperature at varying flow rates
Model GWH 260 PN N for natural gas (NG) supply
Model GWH 260 PN L for liquid propane (LP) supply
15-year warranty on heat exchanger
GWH 260 PN Technical Specifications
Gas input Natural Gas: 30,735 - 74,900 BTU
LP Gas: 30,735 - 74,900 BTU
Minimum flow to activate 0.6 gallons per minute (gpm)
Flow rates 45˚F rise @ 2.6 gpm
55˚F rise @ 2.1 gpm
65˚F rise @ 1.7 gpm
77˚F rise @ 1.5 gpm
90˚F rise @ 1.3 gpm
Thermal Efficiency NG: 78% LP: 78%
Dimensions 28.8" h x 12.2" w x 8.5" d
Weight 25 lbs.
Modulating gas valve yes
Ignition Standing pilot
GWH 260 PN Installation Specifications
Gas connection ¾" Male NPT
Water connections ¾" Male NPT
NG gas pressure Minimum: 7" W.C.
Maximum: 14" W.C.
LP gas pressure Minimum: 11" W.C.
Maximum: 14" W.C.
Water pressure
(Static)
Minimum: 30 PSI
Minimum well pressure: 40PSI
Maximum: 150 PSI
Electrical supply 120VAC - plugs in
Venting 4" double wall B-vent - natural
draft
GWH 260 PN Installation Clearances
Top (A) 12"
Front (B) 4"
Back 0"
Sides 4"
Floor (C) 12"
LIS TED VENT C AP
MINIMUM 6
FEET (1.8M)
LIS TED G AS VENT
ESTABLISH A ONE
FOOT RISE BEFORE
ANY ELBOWS
Fig. 4 Venting configuration
Installation guidelines:
Venting:
4" minimum diameter — do not reduce vent size.
Refer to installation manual for vent material options
Do not combination vent with any power vented appliances.
Establish a one-foot rise before any elbows
Minimum vent height - 6 feet.
 Horizontal sections must slope upwards at least ¼" for every foot
of the horizontal length and be properly supported.
Gas piping:
Heater will not function properly without adequate supply gas
pressure.
Any appliance connector should be ¾" minimum diameter
Plumbing:
Install the included pressure relief valve and pipe to suitable
drain.
Minimum piping diameter is ¾".
Do not solder directly to the bottom of the unit.
Use full port ball valves for isolation valves.

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 15
2.11 Powerstream Pro RP17PT, RP27PT
Features:
Over 90% efficiency rating
10-year warranty on heat exchanger
Durable polymer construction
External temperature control knob
Thermal cut-out for safety
Flow sensor to provide a constant output temperature
Provides an ENDLESS supply of hot water
Weighs less than 25 pounds and fits virtually anywhere
No temperature/pressure relief valve necessary (unless required
by local codes)
Technical Specifications
Model RP17PT RP27PT
Efficiency 90% 94%
Dimensions 15 ½" x 15 ¼" x 4 ½" 15 ½" x 15 ¼" x 4 ½"
Weight 20 lbs. 22 lbs.
Water fittings ¾" Male NPT ¾" Male NPT
Activation rate 0.6 gpm 0.8 gpm
Electrical requirements
Volts 240 240
Kilowatts 17.25kW 26.85kW
Amps U.S.A
Canada
80 (2x40 amps)
80 (1x80 amps)
120 (3x40 amps)
120 (1x120amps)
Wire
size
U.S.A
Canada
8 AWG
(4 conductors & ground)
Check Canadian
Electrical Code
(C22.1-02)
8 AWG
(6 conductors & ground)
Check Canadian
Electrical Code
(C22.1-02)
Phase Single Single
Maximum flow rate at given temperature rise
45°F Rise 2.6 gpm 4.0 gpm
50°F Rise 2.3 gpm 3.7 gpm
60°F Rise 2.0 gpm 3.0 gpm
70°F Rise 1.7 gpm 2.6 gpm
80°F Rise 1.5 gpm 2.2 gpm
Installation guidelines:
Electrical:
Minimum electrical service for RP17PT is 150 amps.
Minimum electrical service for RP27PT is 200 amps.
Minimum wire size for both models is 8 AWG.
Plumbing:
Do not solder directly to connections on the bottom of the unit.
Use unions to facilitate easy future maintenance.
Use full port ball valves for isolation valves.
2 independent
40 amp double-pole
circuit breakers
RP17PT terminal block
Fig. 5 RP17PT Electrical Connections
3 independent
40 amp double-pole
circuit breakers
RP27PT terminal block
Fig. 6 RP27PT Electrical Connections

16 | Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
2.12 Powerstream Pro RP1P, RP2P, RP3P, RP7P,
RP9P, RP12PT
Features:
5-year warranty on heat exchanger
Saves space
Installs vertically or horizontally (Model RP12PT only installs
horizontally)
All models must be hardwired
Solid copper heat exchanger, copper sheathed elements and
tough plastic housing
High/low kW settings possible within most models
Model RP12PT has thermostatic adjustable control
Technical Specifications
Model Part # Wire Size Voltage Amps High kW Low kW Degree rise at flow rates (GPM)* Activation
rate (GPM)
0.5 0.75 1.0 1.5 2.0
RP1P 8AWG 240 40 9.50 — — 84° 64° 42° 32° 0.75
20 — 4.75 — 42° 32° 21° 16°
RP2P 10AWG 277 22 6.00 — 81° 55° 42° 27° — 0.50
11 — 3.00 41° 28° 21° 14° —
RP3P 10AWG 120 29 3.40 — 41° 28° 20° — — 0.50
RP7P 10AWG 240 30 7.20 — — 63° 48° 32° 24° 0.75
15 — 3.60 — 32° 24° 16° 12°
RP9P 8AWG 277 35 9.50 — — 84° 64° 42° 32° 0.75
18 — 4.75 — 42° 32° 21° 16°
RP12PT 6AWG 240 50 12.00 — — 90° 72° 52° 42° 0.75
Installation guidelines:
Electrical:
Refer to the chart below as specification varies by model
Plumbing:
Do not solder directly to connections on the bottom of the unit.
Use unions to facilitate easy future maintenance.
Use full port ball valves for isolation valves.

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 17
2.13 Ariston Pro GL2.5Ti, GL4Ti, GL8Ti
Features:
Point of use mini tank
3 models
Adjustable thermostat with thermal cut-out
Dielectric isolation on inlet/outlet connections
Units can be wall hung (bracket included) or floor mounted
Durable poly-composite housing will not dent and resists corrosion
Temperature/pressure relief valve included (plumb correctly for
discharge)
Simple 120V AC plug-in connection
8-year warranty
Technical Specifications
GL2.5Ti GL4Ti GL8Ti
Tank Volume 2.75 gallons 3.85 gallons 7.0 gallons
Nominal Dimensions 14" x 14" x 11" 14" x 14" x 14" 17 ½" x 17 ½" x 14 ½"
Voltage 120V 120V 120V
Amperage 12.5 amps 12.5 amps 12.5 amps
Wire Type Plug-in Plug-in Plug-in
Heating Capacity 1500 watts 1500 watts 1500 watts
Recovery at 90° rise 7 gph 7 gph 7gph
Temperature range 65-145°F 65-145°F 65-145°F
Water connections ½" NPT ½" NPT ¾" NPT
Maximum water
pressure
150 PSI 150 PSI 150 PSI
Relief valve Installed Installed Included
Installation guidelines:
Electrical:
Follow local codes for electrical outlets for water heaters
All models plugin to standard wall outlet.
Plumbing:
Use full port valves for isolation valves.
Do not solder directly to the plumbing connections.

18 | Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
3 Domestic Water Heating Applications
Potable water
Potable water is water that is suitable for drinking. Bosch Water
Heating appliances are approved to heat potable water only. Heating
any other liquid other than potable water will void the manufactures
warranty covering the appliance.
Introduction
This chapter covers the various application techniques Bosch Water
Heating recommends. The schematics are to be used by professional
contractors in designing a domestic water heating system. The
applications covered range from single sink point-of-use applications
to multi-appliance central domestic recirculation applications.
3.1 Point-of-use applications
Point-of-use applications cover the small applications that a large
water heater would be inefficient for. Installing a smaller heater at a
point-of-use puts the heater near the hot water demand and reduces
the wait for hot water. Common applications for these appliances
include homes, offices, warehouses, service stations, stores,
concession stands, and summer camps.

Applications manual | 11.2007BOSCH THERMOTECHNOLOGY CORPORATION
Applications manual | 19
3.1.1 Ariston mini tank
Simply tap into the cold water line and install the water heater
directly at the sink. All models plug into a standard 120 volt outlet.
Heater can be wall mounted, or sit on the floor.
Symbols
Temperature and pressure
relief valve
Drain pan
Sink
Note: This drawing is conceptual in nature and does not address all design, installation or safety considerations.
Additional safety and/or auxiliary equipment may be needed. This diagram is for reference use by officials, designers and licensed installers.
It is expected that installers have adequate knowledge of accepted industry practices for the equipment, procedures, and applications involved.
Drawing is not to scale.
Ariston Pro GL4 Ti
Ariston Pro GL2.5 Ti
Ariston Pro GL8 Ti
hot
hot
hot
cold
cold cold
Drawing # POU1 CN rev 06/06
Flow direction
Service valve

20 | Applications manual
Application manual | 11.2007 BOSCH THERMOTECHNOLOGY CORPORATION
3.1.2 Powerstream Pro electric point-of-use tankless water heater
PowerstreamPro point-of-use water heaters come in four models to
serve a wide range of applications. Finding the right model depends
upon your desired temperature and flow rate. Use the table below to
find the model best suited to your customer‘s needs. Flow controls
and faucet aerators can greatly enhance performance.
Note: Water heater must be filled with water and purged of air prior
to supplying power.
Symbols
Service valve
Sink
Note: This drawing is conceptual in nature and does not address all design, installation or safety considerations.
Additional safety and/or auxiliary equipment may be needed. This diagram is for reference use by officials, designers and licensed installers.
It is expected that installers have adequate knowledge of accepted industry practices for the equipment, procedures, and applications involved.
Drawing is not to scale.
Drawing # POU2 CN rev 06/07
hot
cold supply
hot cold
Flow direction
hot
hot
cold
cold supply
Powerstream Pro
RP1P, RP2P, RP3P,
RP7P, RP9P, RP12PT
Powerstream Pro
RP1P, RP2P, RP3P,
RP7P, RP9P, RP12PT