BOSER Technology HS-4703 User manual

HS-4703
800MHz FSB Pentium®4
Embedded Engine Board
•800MHz FSB•DDR•PCI Slot•
•CRT/LVDS Panel•TV-Out•
•Giga LAN•Audio•Serial ATA•
ATA/33/66/100•RS-232/422/485•
•4 COM•USB2.0•WDT•H/W Monitor•
•5.25” Industrial Embedded Engine Board•

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review
before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is
not liable for any infringements of patents or other rights resulting from its use. The
manufacturer will not be responsible for any direct, indirect, special,
incidental or consequential damages arising from the use of this product or
documentation, even if advised of the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation,
and storage of any form and means (i.e., electronic, mechanical, photocopying,
recording) of this document, in whole or partly, is prohibited, unless granted
permission by BOSER Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the
contents of this document without due notice. BOSER Technology Co., Ltd.
assumes no responsibility for any errors or omissions that may appear in this
manual, nor does it make any commitment to update the information contained
herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2004 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.0, November 24, 2004

Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features ............................................................. 2
1.2 Specifications .............................................................. 3
1.3 Board Dimensions....................................................... 4
Chapter 2 Unpacking ..................................................5
2.1 Opening the Delivery Package................................... 5
2.2 Inspection..................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ....................................................... 7
3.2 Board Layout ............................................................... 8
3.3 Jumper List .................................................................. 9
3.4 Connector List ............................................................. 9
3.5 Configuring the CPU ................................................. 10
3.6 System Memory ......................................................... 10
3.7 VGA Controller........................................................... 10
3.8 Serial ATA Function ....................................................11
3.9 PCI E-IDE Drive Connector....................................... 12
3.10 Floppy Disk Drive Connector ................................... 13
3.11 Serial Port Connectors.............................................. 14
3.12 Parallel Connector..................................................... 15
3.13 Ethernet Connector ................................................... 16
3.14 USB Connector .......................................................... 16
3.15 CMOS Data Clear ....................................................... 17
3.16 Power and Fan Connectors...................................... 18
3.17 Keyboard and Mouse Connector ............................. 19
3.18 TV-Out Function......................................................... 19
3.19 GPIO Connector......................................................... 19
3.20 System Front Panel Connectors.............................. 20
3.21 Watchdog Timer......................................................... 21
3.22 Audio Connectors ..................................................... 22

Chapter 4 Award BIOS Setup .................................23
4.1 Starting Setup ............................................................ 23
4.2 Using Setup................................................................ 24
4.3 Main Menu .................................................................. 25
4.4 Standard CMOS Features ......................................... 26
4.5 Advanced BIOS Features ......................................... 27
4.6 Advanced Chipset Features ..................................... 28
4.7 Integrated Peripherals............................................... 29
4.8 Power Management Setup........................................ 31
4.9 PnP/PCI Configurations ............................................ 32
4.10 PC Health Status........................................................ 33
4.11 Frequency/Voltage Control....................................... 33
4.12 Load Fail-Safe Defaults............................................. 34
4.13 Load Optimized Defaults .......................................... 35
4.14 Set Supervisor/User Password................................ 35
4.15 Save & Exit Setup ...................................................... 37
4.16 Exit Without Saving................................................... 38
Chapter 5 Software Utilities.....................................39
5.1 IDE Driver Installation ............................................... 40
5.2 VGA Driver Installation.............................................. 43
5.3 LAN Driver Installation .............................................. 50
5.4 Audio Driver Installation ........................................... 60
5.5 USB2.0 Driver Installation......................................... 62

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity.
To avoid damaging chips from electrostatic discharge, observe the
following precautions:
 Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion
of the system unit chassis for a few seconds. This helps to discharge any
static electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR
clip of the strap to the end of the shielded wire lead from a grounded
object. Please wear and connect the strap before handling the HS-4703
to protect yourself from the discharge of any static electricity through the
strap.
 Please use an anti-static pad when putting down any components or
parts or tools outside the computer. You may also use an anti-static bag
instead of the pad. Please inquire from your local supplier for additional
assistance in finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENT WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTION.

1
Chapter 1
General Description
The HS-4703 is an Intel®82865GV/82801ER chipset-based board
designed for PCI Bus PGA 478 Intel®Pentium®4 CPU up to 3.06GHz
compatibility. The combination of these features makes the HS-4703
an ideal all-in-one industrial single board computer. Additional features
include an enhanced I/O with CRT/LVDS Panel, TV-Out, Giga LAN,
audio, 4 COM and USB2.0 port interface.
Its onboard ATA/33/66/100 connected to IDE drive interface
architecture allows the HS-4703 to support data transfers of 33, 66 or
100MB/sec. for each IDE drive connection. Designed with the Intel®
82865GV/82801ER core logic chipset, the board supports all PGA 478
Pentium®4 CPU up to 3.06GHz. The display controller is Intel®
82865GV supporting CRT displays up to 1600 x 1200. It also provides
24-bit/48-bit LVDS Panel display interface.

2
Serial ATA is the revolutionary ATA interface that provides scalable
performance for IDE device. With up to 150MB/sec. data transfer rate,
serial ATA is faster than the current parallel ATA and delivers superior
input/output performance. In addition, the serial ATA interface is
furnished with RAID 0/1 function for extra performance enhancement
and data protection.
System memory is also sufficient with the one DDR socket that can
supports DDR-266/333/400 up to 1GB. 800MHz FSB CPU can support
DDR-400, 533MHz FSB CPU, can supports DDR-333, and 400MHz
FSB CPU can supports DDR-266.
Additional onboard connectors include an advanced USB2.0 port
providing faster data transmission, and one external RJ-45 connector
for use of 100/1000 or 10/100 Based Ethernet interface.
1.1 Major Features
The HS-4703 comes with the following features:
 PGA 478 for Intel® Pentium®4 (Northwood/0.13 micron/512KB L2 cache)
up to 3.06GHz CPU
 Supports 400/533/800MHz FSB
 One DDR socket with a max. capacity of 1GB

3
 Intel®82865GV/82801ER system chipset
 Winbond W83627HF and Fintek F81216D super I/O chipset
 Intel®82865GV CRT display controller
 Intel®82562EX 10/100 Based or 82547EI 100/1000 Based LAN
 AC97 3D audio controller
 Supports Serial ATA controller
 Fast PCI ATA/33/66/100 IDE controller
 Four COM, eight USB2.0 connectors
 Supports Hardware Monitor
 Supports LVDS Panel interface (optional)
 Supports TV-Out function (optional)
1.2 Specifications

CPU: PGA 478 for Intel®Pentium®4 (Northwood/0.13 micron/512KB L2
cache) up to 3.06GHz CPU

Bus Interface: PCI Bus

Front Side Bus: Supports 400/533/800MHz FSB

Memory: One DDR socket supporting DDR-333/400 up to 1GB

Chipset: Intel®82865GV/82801ER

I/O Chipset: Winbond W83627HF, Fintek 81216D

PCI Slot: One standard PCI slot

VGA: Intel®82865GV supporting CRT display up to 1600 x 1200

LVDS Panel: Supports 24-bit dual channel LVDS Panel interface (optional)

TV-Out: Supports PAL or NTSC TV systems (optional)

LAN: Intel®82562EX 10/100 Based or 82547EI 100/1000 Based LAN

Audio: AC97 3D audio controller

Serial ATA: Intel®ICH5 controller and with two ports supporting transfer
rate up to 150MB/sec.
 IDE: Four IDE disk drives supporting ATA/33/66/100 with transfer rates of
up to 33/66/100MB/sec.

FDD: Supports up to two floppy disk drives

Parallel: One enhanced bi-directional parallel port supporting SPP/ECP/
EPP
 Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232 x
3 serial ports with 16-byte FIFO

USB: Eight USB2.0 connectors, six internal and two external

Keyboard: PS/2 6-pin Mini DIN

Mouse: PS/2 6-pin Mini DIN

4

BIOS: Award PnP Flash BIOS

Watchdog Timer: Software programmable time-out intervals from
1~256sec.

CMOS: Battery backup

Power Connector: One 4-pin and one 20-pin ATX power connectors

Temperature: 0~+60°C (operating); -20~+80°C (storage)

Hardware Monitor: Winbond W83627HF

Board Size: 20.3(L) x 14.6(W) x 3.3(H) cm
1.3 Board Dimensions

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-4703 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Make sure all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
are firmly seated. The HS-4703 delivery package contains the following
items:

HS-4703 Board x 1
 Utility CD Disk x 1

Cables Package x 1
 Cooling Fan x 1

Jumper Bag x 1
 User’s Manual

6
Cables Package
NO. Description
1 Two USB flat cable with bracket x 1
2 ATA/100 IDE flat cable x 2
3 Two COM and RCA Jack flat cable with bracket x 1
4 Floppy flat cable x 1
5 Parallel port flat cable x 1
6 Serial ATA cable x 1
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-4703. This chapter also contains information related to
jumper settings of switch, watchdog timer etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (Set JP2 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.

8
3.2 Board Layout

9
3.3 Jumper List
Jumper Default Setting Setting Page
JP1 COM2 Use RS-232 or RS-422/485 Select:
RS-232
Short 1-3, 2-4,
7-9, 8-10 14
JP2 Clear CMOS: Normal Operation 1-2 Short 17
3.4 Connector List
Connector Definition Page
CN1(1-6) PS/2 6-pin Mini DIN Keyboard Connector 19
CN1(7-12) PS/2 6-pin Mini DIN Mouse Connector 19
CN2(1-9) COM1 Connector (DB9) 14
CN2(10-18) COM2 Connector (DB9) 14
CN3(1-15) 15-pin CRT Connector (DB15) 10
CN3(17-32) External Audio Connector 22
CN4 20-pin ATX Power In Connector 18
CN5(1-12) RJ-45 Connector 16
CN5(17-26) External USB2.0 Connector 16
CN6 RS-422/485 Connector (5x2 header) 14
CN7 4-pin ATX Power In Connector 18
CN8 / CN9 / CN13(33-40) Internal USB2.0 Connector 16
CN11 / CN10 COM3/COM4 Connector (5x2 header) 14
CN12 Parallel Connector 15
CN13(1-16) System Front Panel Connector 20
CN13(17-22) Internal LAN Link/Active LED Connector 16
CN13(25-32) Internal Mic In/Audio Out Connector 22
DM1 188-pin DDR Socket 10
J1 / J2 / J3 Fan Power Connector 18
J4 / J6 24-bit LVDS Panel Connector 10
J5 Inverter Power In Connector 10
J8 /J9 IDE Connector 12
J12 GPIO Connector 19
J13 FDD Connector 13
J14 / J15 Serial ATA Connector 11
J16 TV-Out Connector 19

10
3.5 Configuring the CPU
The HS-4703 provides 800MHz FSB Intel®Pentium®4 (0.13
micron/512KB L2 cache) up to 3.06GHz CPU. It offers the convenience
in CPU installation with its auto-detect feature. After installing a new
microprocessor onboard, the HS-4703 automatically identifies the
frequency and clock speed of the installed microprocessor chip,
thereby eliminating the need for user to do additional CPU
configuration or hardware settings related to it.
3.6 System Memory
The HS-4703 provides one DDR socket at location DM1. The
maximum capacity of the onboard memory is 1GB.
3.7 VGA Controller
The onboard Intel®82865GV supports CRT display up to 1600 x 1200.
The HS-4703 provides two methods of connecting VGA device.
CN3(1-16) offers a single standard CRT connector (DB15), or J4/J6
offer 24-bit/48-bit LVDS panel connectors.
 CN3(1-15): 15-pin CRT Connector (DB15)
PIN Description PIN Description
1 RED 2 GREEN
3 BLUE 4 N/C
5 GND 6 GND
7 GND 8 GND
9 N/C 10 GND
11 N/C 12 SDA
13 HSYNC 14 VSYNC
15 SCL
1
6
10
11
515
 J5: Inverter Power In Connector
PIN Description
1 +12V
2 +12V
3 VCC
4 BackLight Enabled
5 LCD Enabled
6 GND
1 6

11
 J4: 24-bit LVDS Panel Connector
PIN Description PIN Description
1 VCC3 2 VCC3
3 GND 4 GND
5 A0- 6 A0+
7 A1- 8 A1+
9 A2- 10 A2+
11 CLK1- 12 CLK1+
13 A3- 14 A3+
1
214
13
 J6: 24-bit LVDS Panel Connector
PIN Description PIN Description
1 VCC3 2 VCC3
3 GND 4 GND
5 A4- 6 A4+
7 A5- 8 A5+
9 A6- 10 A6+
11 CLK2- 12 CLK2+
13 A7- 14 A7+
1
214
13
NOTE: If using J6 only, it just supports 24-bit LVDS Panel; If you want to
use 48-bit LVDS Panel, please using J6 and J4 combined.
3.8 Serial ATA Function
You can connect the Serial ATA device to this connector provides you
high speeds transfer rates (150MB/sec.). If you wish to use RAID
function, please note that these two Serial ATA connectors just support
RAID0 and only compatible with WIN XP.
 J14/J15: Serial ATA Connector
PIN Description
1 GND
2 SATATXP
3 SATATXN
4 GND
5 SATARXN
6 SATARXP
7 GND
GND
SATATXP
SATATXN
GND
17
SATARXN
SATARXP
GND

12
IDE and Serial ATA Device Configurations
Following are the IDE and Serial ATA device configurations supported
by Intel ICH5 specifications.
Native operating systems (OS) are Windows 2000/XP. ICH5 supports
a maximum of six devices using these OS.
Legacy OS are MS-DOS, Windows 95/98/Me/NT4.0. ICH5 supports a
maximum of four devices using these OS.
Operating System IDE Serial ATA
WIN 2000/XP Primary/Secondary Port0/Port1
Primary Port0/Port1
Secondary Port0/Port1
WIN 95/98/Me/NT4.0
Primary/Secondary ----
3.9 PCI E-IDE Drive Connector
J8 and J9 are standard 40-pin daisy-chain driver connector that serves
the PCI E-IDE drive provisions onboard the HS-4703. A maximum of
four ATA/33/66/100 IDE drives can be connected to the HS-4703 via J8
and J9.
 J8/J9: IDE Connector
PIN Description PIN Description
1 RESET 2 GND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GND 20 N/C
21 PDREQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 PIORDY 28 PR1PD1-
29 RPDACK- 30 GND
31 Interrupt 32 N/C
33 RPDA1- 34 PATA66
35 RPDA0- 36 RPDA2-
…More On Next Page…

13
PIN Description PIN Description
37 RPCS1- 38 RPCS3-
39 HDD Active 40 GND
1
240
39
3 5 7 9 17 19 21 23 25 27 29 31 33 11 13 15 35 37
46810 18 20 22 24 26 28 30 32 34
12 14 16 36 38
3.10 Floppy Disk Drive Connector
The HS-4703 uses a standard 34-pin header connector, J13, for floppy
disk drive connection. A total of two FDD drives may be connected to
J13 at any given time.
 J13: FDD Connector
PIN Description PIN Description
1 GND 2 DRVDEN0
3 GND 4 N/C
5 GND 6 DRVDEN1
7 GND 8 INDEX#
9 GND 10 MTR0#
11 GND 12 DS1#
13 GND 14 DS0#
15 GND 16 MTR1#
17 GND 18 DIR#
19 GND 20 STEP#
21 GND 22 WDATA#
23 GND 24 WGATE#
25 GND 26 TRAK00#
27 GND 28 WRTPRT#
29 GND 30 RDATA#
31 GND 32 HDSEL#
33 GND 34 DSKCHG#
1
234
33

14
3.11 Serial Port Connectors
The HS-4703 offers two NS16C550 compatible UARTs with
Read/Receive 16-byte FIFO serial ports and four internal 10-pin
headers.
 CN2(1-9): COM1 Connector (DB9)
PIN Description PIN Description
1 DCD1 6 DSR1
2 RXD1 7 RTS1
3 TXD1 8 CTS1
4 DTR1 9 RI1
5 GND
16
59
 CN2(10-18): COM1 Connector (DB9)
PIN Description PIN Description
10 DCD2 15 DSR2
11 RXD2 16 RTS2
12 TXD2 17 CTS2
13 DTR2 18 RI2
14 GND
16
59
 CN11/CN10: COM3/COM4 Connector (5x2 header)
PIN Description PIN Description
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 N/C
2
4
6
8
10
1
3
5
7
9
DSR
RTS
CTS
N/C
RI
DCD
RXD
TXD
GND
DTR
 CN6: RS-422/485 Connector (5x2 header)
PIN Description PIN Description
1 TX- 2 TX+
3 RX+ 4 RX-
5 GND 6 RTS-
7 RTS+ 8 CTS+
9 CTS- 10 N/C
2
4
6
8
10
1
3
5
7
9
TX+
RX-
RTS-
N/C
CTS+
TX-
RX+
GND
CTS-
RTS+