BOSER Technology HS-4700 User manual

HS-4700
PGA 478 Pentium®4
Industrial Embedded Engine Board
•All-in-One•CRT/Panel•PCI Slot•
•ATA/33/66/100•Dual LAN•Audio•4COM•
•IrDA•USB•H/W Monitor•

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of
this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the contents of
this document without due notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or registered
trademarks of their respective companies or owners.
© Copyright 2003 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.2, October 19, 2004

Table of Contents
Chapter 1 General Description……………………….1
1.1 Major Features....................................................................2
1.2 Specifications .....................................................................3
1.3 Board Dimensions..............................................................4
Chapter 2 Unpacking…………………………………5
2.1 Opening the Delivery Package..........................................5
2.2 Inspection............................................................................5
Chapter 3 Hardware Installation…………………….7
3.1 Before Installation ..............................................................7
3.2 Board Layout ......................................................................8
3.3 Jumper List .........................................................................9
3.4 Connector List ....................................................................9
3.5 Configuring the CPU ........................................................10
3.6 System Memory ................................................................10
3.7 VGA Controller .................................................................10
3.8 SMI Signal Input Switch...................................................12
3.9 PCI E-IDE Drive Connector..............................................12
3.10 Floppy Disk Drive Connector ..........................................14
3.11 Serial Port Connectors ....................................................15
3.12 Parallel Connector............................................................16
3.13 Ethernet Connector..........................................................17
3.14 USB Connector.................................................................18
3.15 CMOS Data Clear..............................................................18
3.16 Power and Fan Connectors.............................................19
3.17 Keyboard/Mouse Connectors .........................................20
3.18 System Front Panel Connectors.....................................21
3.19 External Speaker ..............................................................22
3.20 IrDA Connector.................................................................22
3.21 Audio Connectors ............................................................23

Chapter 4 AMI BIOS Setup…………………………25
4.1 Starting Setup...................................................................25
4.2 Using Setup ......................................................................26
4.3 Main Menu.........................................................................27
4.4 Standard CMOS Setup.....................................................28
4.5 Advanced CMOS Setup ...................................................29
4.6 Advanced Chipset Setup.................................................30
4.7 Power Management Setup ..............................................31
4.8 PCI / Plug and Play Setup................................................32
4.9 Peripheral Setup...............................................................33
4.10 Hardware Monitor Setup .................................................34
4.11 Auto-Detect Hard Disks...................................................35
4.12 Change Supervisor/User Password...............................36
4.13 Auto Configuration with Optimal Settings ....................37
4.14 Auto Configuration with Fail Safe Settings...................38
4.15 Save Settings and Exit.....................................................39
4.16 Exit Without Saving .........................................................40
Chapter 5 Software Utilities………………………...41
5.1 IDE Driver Installation......................................................41
5.2 VGA Driver Installation for Win 95/98 ............................47
5.3 LAN Driver Installation ....................................................49
5.4 Audio Driver Installation..................................................69

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
 Do not remove boards or integrated circuits from their anti-static packaging
until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This helps to discharge any static
electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR clip
of the strap to the end of the shielded wire lead from a grounded object.
Please wear and connect the strap before handle the HS-4700 to ensure
harmlessly discharge any static electricity through the strap.
 Please use an anti-static pad when putting down any components or parts or
tools outside the computer. You may also use an anti-static bag instead of the
pad. Please inquire from your local supplier for additional assistance in finding
the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTION.

This Page is intentionally left blank.

1
Chapter 1
General Description
The HS-4700 is an Intel®82845 chipset-based board designed for PCI
Bus PGA 478 Intel®Pentium®4 1.2~2.2GHz(400MHz FSB) CPU
compatibility. These features combine and make the HS-4700 an ideal
all-in-one industrial single board computer. Additional features include
an enhanced I/O with CRT/Panel, Dual LAN, Audio and 4COM ports
interface.
Its onboard ATA/33/66/100 to IDE drive interface architecture allows
the HS-4700 to support data transfers of 33, 66 or 100MB/sec. to each
IDE drive connection. Designed with the Intel® 82845 core logic
chipset, the board supports all PGA 478 Pentium®4 CPU series
operating at 1.2GHz to 2.2GHz(400MHz FSB). The CRT/Panel display
controller is C&T 69030 with 4MB memory supporting up to 1600 x
1200 at 64K colors.
System memory is also sufficient with the three DIMM sockets that can
support up to 1.5GB.
Additional onboard connectors include an advanced USB and IrDA
ports providing faster data transmission, and two internal 5x2
connectors for 10/100 Base-TX Ethernet use.

2
1.1 Major Features
The HS-4700 comes with the following features:
 PGA 478 for Intel®Pentium®4 1.2~2.2GHz(400MHz FSB) CPU
 Intel®82845/82801BA system chipset
 Three DIMM sockets with a max. capacity of 1.5GB
 Winbond W83627 super I/O chipset
 Fast PCI ATA/33/66/100 IDE controller
 Four RS-232 serial ports
 C&T 69030 CRT/Panel display controller
 Intel®82559 and Intel®82562 10/100 Based LAN
 AC97 3D audio controller
 Supports ATX power function
 Supports Hardware Monitor function

3
1.2 Specifications

CPU: PGA 478 for Intel®Pentium®4 1.2~2.2GHz(400MHz FSB) CPU

Bus Interface: PCI Bus

Memory: Three DIMM sockets supporting up to 1.5GB

Chipset: Intel®82845/82801BA

I/O Chipset: Winbond W83627 x 2

VGA: C&T 69030 with 4MB memory supporting CRT/Panel displays up
to 1600 x 1200 at 64K colors
 IDE: Four IDE disk drives supporting ATA/33/66/100 and with transfer
rates of up to 33/66/100MB/sec.

FDD: Supports up to two floppy disk drives

Parallel: One enhanced bi-directional parallel port supporting
SPP/ECP/EPP
 LAN: Intel®82559 and one Intel®82562 10/100 Based LAN
 Audio: AC97 3D audio controller
 Serial Port: 16C550 UART-compatible RS-232 x 4 serial ports with
16-byte FIFO

IrDA: One IrDA TX/RX header

USB: Two USB connectors (USB 1.1)

Keyboard/Mouse: 8-pin connector supporting standard PC/AT
keyboard and PS/2 mouse
 BIOS: AMI PnP Flash BIOS
 CMOS: Battery backup
 Power Connector: One 4-pin and one 20-pin ATX power connector
 Operating Temperature: 0~60°C
 Hardware Monitor: Winbond W83627

Board Size: 20.3 x 16.1 cm

4
1.3 Board Dimensions

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-4700 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, and keyboard controller chip to ensure
that they are firmly seated. The HS-4700 delivery package contains the
following items:

HS-4700 Board x 1
 Utility CD Disk x 1

ATA/100 IDE flat cable x 2
 FDD flat cable x 1

Parallel flat cable x 1
 VGA cable +DB15 x 1

10-pin LAN cable + RJ-45 connector x 2
 8-pin USB split type cable with bracket x 1

MIC/Audio 8-pin cable + 2 phone jacks x 1
 4-in-1 COM Port cable + DB9 connectors x 1

PS/2 K/B & Mouse split-type cable x 1
 Jumper Bag x 1

User’s Manual

6
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-4700.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (Set JP3 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.
4. Make sure your power supply is using for P4 only. One of 4-pin
connector is for +12V lead which should connect to PW1 and
20-pin ATX connector to PW2.

8
3.2 Board Layout

9
3.3 Jumper List
Jumper Default Setting Setting
JP1 Panel Voltage +12V In Enabled/Disabled: Enabled Short
JP2 Panel Voltage Select: +3.3V Short 1-2
JP3 Clear CMOS: Normal Operation Short 2-3
JP4 LAN2 Enabled/Disabled Select: Enabled Short 1-2
3.4 Connector List
Connector Definition
CD1 CD Analog Input Connector
CD2 Line In Analog Input Connector
CN1 Keylock Connector
CN2 SMI Signal Input Connector
CN3 2-pin ATX Power On/Off Switch
CN4 HDD LED Connector
CN6 External Speaker Connector
CN7 Reset Connector
CN8 Green LED Connector
CN11 50-pin Panel Connector
CN12 MIC In/Audio Out Connector
CN13 LAN2 Connector
CN14 LAN1 Connector
CN15 CRT Connector
CN16 COM1 Connector
CN17 COM2 Connector
CN18 COM3 Connector
CN19 COM4 Connector
DM1, DM2, DM3 168-pin DIMM Sockets
PW1 4-pin ATX Power Connector
PW2 20-pin ATX Power Connector
PCI1 PCI Connector
IR1 IrDA Connector
FDC1 Floppy Connector
FN1, FN2, FN3 Fan Connectors
IDE1, IDE2 IDE Connectors
KB1 KB/Mouse Connector
LPT1 Parallel Connector
USB1, USB2 USB Connectors
S1 Chassis Open Switch Connector

10
3.5 Configuring the CPU
The HS-4700 offers the convenience in CPU installation with its
auto-detect feature. After installing a new microprocessor onboard, the
HS-4700 automatically identifies the frequency and clock speed of the
installed microprocessor chip, thereby eliminating the need for user to
do additional CPU configuration or hardware settings related to it.
3.6 System Memory
The HS-4700 provides three DIMM sockets at locations DM1, DM2 and
DM3. The maximum capacity of the onboard memory is 1.5GB.
3.7 VGA Controller
The onboard C&T 69030 with 4MB memory supporting CRT/Panel
displays up to 1600 x 1200 at 64K colors. The HS-4700 provides two
connection methods of CRT and Panel device. CN15 offers an internal
CRT connector, and CN11 offers a 50-pin Panel connector.
 CN15: CRT Connector
PIN Description PIN Description
1 Red 2 GND
3 Green 4 GND
5 Blue 6 GND
7 GND 8 DDCDTA
9 GND 10 HSYNC
11 GND 12 VSYNC
13 GND 14 DDCK
15 GND 16 N/C
2
16
1
15
Red
Green
Blue
GND
GND
GND
GND
GND
GND
GND
GND
DDCDTA
HSYNC
VSYNC
DDCK
N/C

11
 CN11: 50-pin Panel Connector
PIN. Description PIN Description
1 +12V 2 +12V
3 GND 4 GND
5 3.3V / 5V Note 6 ENAVDD
7 ENAVEE 8 GND
9 P0 10 P1
11 P2 12 P3
13 P4 14 P5
15 P6 16 P7
17 P8 18 P9
19 P10 20 P11
21 P12 22 P13
23 P14 24 P15
25 P16 26 P17
27 P18 28 P19
29 P20 30 P21
31 P22 32 P23
33 P24 34 P25
35 FPSCLK 36 FLM
37 M 38 LP
39 GND 40 ENABKL
41 P26 42 P27
43 P28 44 P29
45 P30 46 P31
47 P32 48 P33
49 P34 50 P35
12
5049
+12V
GND
3.3V/5V
ENAVEE
P0
P2
P4
P6
P8
P10
P12
P14
P16
P18
P20
+12V
GND
ENAVDD
GND
P1
P3
P5
P7
P9
P11
P13
P15
P17
P19
P21
P22
P24
FPSCLK
M
GND
P26
P28
P30
P32
P34
P23
P25
FLM
LP
ENABKL
P27
P29
P31
P33
P35
Jumper JP2 offers two voltage settings and JP1 is +12V in for the user.
 JP2: Panel Voltage Select
Options Settings
+3.3V (default) Short 1-2
+5V Short 2-3
+3.3V
To CN11 pin-5
VCC
13

12
 JP1: Panel Voltage +12V In Enabled/Disabled Select
Options Settings
* Enabled Short
Disabled Open
+12V
to CN11 pin-1, pin-2
12
3.8 SMI Signal Input Switch
HS-4700 has an SMI connector at location CN2. If there is an external
SMI Signal Input Switch, this input switch will be able to receive signals.
 CN2: SMI Signal Input Switch
PIN Description
1 EXT_SMI
2 GND
12
3.9 PCI E-IDE Drive Connector
IDE1 and IDE2 are standard 40-pin connector daisy-chain driver
connector serves the PCI E-IDE drive provisions onboard the HS-4700.
A maximum of four ATA/33/66/100 IDE drives can connect to the
HS-4700 via IDE1 and IDE2.
 IDE1: Primary IDE Connector
PIN Description PIN Description
1 IDERST# 2 GND
3 PDD7 4 PDD8
5 PDD6 6 PDD9
7 PDD5 8 PDD10
9 PDD4 10 PDD11
11 PDD3 12 PDD12
13 PDD2 14 PDD13
15 PDD1 16 PDD14
17 PDD0 18 PDD15
19 GND 20 N/C
21 PDREQ 22 GND
23 PDIOW# 24 GND
25 PDIOR# 26 GND
•••More On Next Page•••

13
PIN Description PIN Description
27 PIORDY 28 470ΩPull GND
29 PDDACK# 30 GND
31 IRQ14 32 N/C
33 PDA1 34 P66DET
35 PDA0 36 PDA2
37 PDCS#1 38 PDCS#3
39 IDEACTP# 40 GND
IDERST#
PDD7 PDD6 PDD5 PDD4 PDD0
GND
PDREQ
PDIOW#
PDIOR#
PIORDY
PDDACK#
IRQ14
PDA1
PDD3 PDD2 PDD1
PDA0
PDCS#1
IDEACTP#
GND PDD8 PDD9 PDD10 PDD11 PDD15 N/C GND ’ GND GND 470ΩPull GND GND N/C P66DET PDD12 PDD13 PDD14 PDA2 PDCS#3 GND
1
240
39
 IDE2: Secondary IDE Connector
PIN Description PIN Description
1 IDERST# 2 GND
3 SDD7 4 SDD8
5 SDD6 6 SDD9
7 SDD5 8 SDD10
9 SDD4 10 SDD11
11 SDD3 12 SDD12
13 SDD2 14 SDD13
15 SDD1 16 SDD14
17 SDD0 18 SDD15
19 GND 20 N/C
21 SDREQ 22 GND
23 SDIOW# 24 GND
25 SDIOR# 26 GND
27 SIORDY 28 470ΩPull GND
29 SDDACK# 30 GND
31 IRQ15 32 N/C
33 SDA1 34 S66DET
35 SDA0 36 SDA2
37 SDCS#1 38 SDCS#3
39 IDEACTP# 40 GND

14
IDERST#
SDD7 SDD6 SDD5 SDD4 SDD0
GND
SDREQ
SDIOW#
SDIOR#
SIORDY
SDDACK#
IRQ15
SDA1
SDD3 SDD2 SDD1
SDA0
SDCS#1
IDEACTP#
GND SDD8 SDD9 SDD10 SDD11 SDD15 N/C GND ’ GND GND 470ΩPull GND GND N/C S66DET SDD12 SDD13 SDD14 SDA2 SDCS#3 GND
1
240
39
3.10 Floppy Disk Drive Connector
The HS-4700 uses a standard 34-pin header connector, FDC1, for
floppy disk drive connection. A total of two FDD drives may be
connected to FDC at any given time.
 FDC1: FDD Connector
PIN Description PIN Description
1 GND 2 RWC#
3 GND 4 N/C
5 GND 6 DS1#
7 GND 8 Index#
9 GND 10 MOA#
11 GND 12 DSB#
13 GND 14 DSA#
15 GND 16 MOB#
17 GND 18 DIR#
19 GND 20 STEP#
21 GND 22 WD#
23 GND 24 WE#
25 GND 26 TRACK0#
27 GND 28 WP#
29 N/C 30 RDATA#
31 GND 32 HEAD#
33 N/C 34 DSKCHG#