Boyd Belvedere I User manual

TEL [phone] · FAX [phone] · BOYDLIGHTING.COM
BOYD LIGHTING · 3 0 LIBERTY SHIP WAY SUITE 3150 · SAUSALITO CA 94965
12.05.16Page 1 of 2
Installation Instructions
E10308 Belvedere I Lantern
E10309 Belvedere II Lantern
Lamping Specications
•Incandescent lamping
Medium Base, Four, T-10, 60w max
•Fluorescent Lamping 120v or 277v
One,CFQ26W/G24q-3 or
One,CFTR26W/GX24q or
One,CFTR32W/GX24q or
One,CFTR42W/GX24q
IMPORTANT | CAUTION
READ ALL INSTRUCTIONS THOROUGHLY.
TURN OFF POWER AT CIRCUIT BREAKER OR
FUSE BOX BEFORE PROCEEDING.
IMPORTANT! AT ALL TIMES WIRING
TO BE DONE PER NATIONAL ELECTRIC
CODES (NEC) OR APPLICABLE LOCAL
CODES
Figure 1
Figure 2
IMPORTANT | CAUTION
Read all instructions thoroughly, and turn off power at
circuit breaker or fuse box before proceeding.
Step 1 Remove xture and all xture components from
packaging. Avoid using sharp blade on packaging as it may
damage the finish or the glass diffusers. Locate and disas-
semble the suspension hardware components. To begin the
installation process, locate the mounting bracket, threaded
pipe and misc. washers and retaining nuts and hardware.
(See Figure 1)
IMPORTANT: Do Not Rely on the outlet box for sole
mounting as it is not adequate to support the weight of the
fixture. Fixture must be mounted to a structural member
such as a ceiling stud/timber or similar component with
adequate hardware that can support a minimum weight of
216 lbs.
Step 2 Locate outlet box and with the power turned off at
the circuit attach the mounting bracket to the outlet box.
Include a structural member such as a steel angle bracket or
stud that is secured into the ceiling and meets local building
codes. Route the steel pipe up and through the center of
the outlet box and through the additional support mem-
ber. The threaded pipe can be cut to length. Use additional
hardware to fasten the pipe and mounting bracket securely
to the ceiling. (See Figure 2)
Step 3 Fixture housing and stem assembly: depending on
the overall height of the fixture, it may be necessary to
assemble the upper components of the assembly as they
may have been disassembled for shipping purposes. Begin
the assembly process by routing the wires up and through
the stems. Use Loctite 2440 thread locker or equivalent on
the threads and thread the support stems onto the top of
the fixture housing, fasten securely. (See Figure 3)
Step 4 Locate and slide the canopy cover down the stems
and carefully rest on top of the fixture hood. Next attach
the canopy to the upper stems. Attach the additional rein-
forcement brackets and secure into place with the retainer
nuts and lock washers. (See Figure 3)

TEL [phone] · FAX [phone] · BOYDLIGHTING.COM
BOYD LIGHTING · 3 0 LIBERTY SHIP WAY SUITE 3150 · SAUSALITO CA 94965
Page 2 of 2
Figure 3
Figure 4
Step 5 Carefully lift the fixture up and into position over
the ceiling mounting bracket. The bracket contains two
1/4-20 screws that protrude downward. Align the screws
from the ceiling mounting bracket with the holes in the
fixture’s canopy and reinforcement plates. Secure into
position with lock washers and nuts.
Step 6 Once the fixture is mounted securely into position
make the electrical connections. Make wire connections
using twist-on connectors: connect the black fixture wire
to the hot supply wire (typically black); connect the white
fixture wire to the neutral supply wire (typically white);
connect the copper fixture wire to the ground wire or
ground terminal at the outlet box, push field wiring con-
nections into the junction box. (See Figures 2 and 3)
Step 7 With connections made and wiring tucked into the
junction box, carefully lift the canopy cover up and into
position and secure into place with the decorative knob
and threaded nipple.
Step 8 If installing in an area exposed to moisture or
weather apply weather proof caulking or silicon type adhe-
sive to the perimeter of the canopy at the ceiling to pre-
vent moisture from entering between fixture canopy and
the ceiling.
Step 9 Install lamps per label recommendations, lamps can
be installed by reaching up through the bottom of the fix-
ture.
Step 10 Install glass diffuser panels into the housing.
Position the diffuser so that the ribbed portion of the
glass faces outward. The diffuser can be lifted into posi-
tion behind upper retainer bracket and then lowered into
channel bracket on the bottom. Install the lower diffuser
through the opening in the bottom of the housing and ori-
ent into position. (See Figure 4)
Step 11 Restore power to circuit and confirm proper
installation.