Boyo VTW73M User manual

VTW73M
◆VTW73M
7.3 Inch Car Rear View Mirror Monitor with Built-In Miracast

Welcome to use our 7.3 inch car rear view mirror monitor with built-in miracast
●We reserve the final explanation right on this User's Manual.
●Specifications are subjected to change without notice. Sorry for any
inconvenience caused!
●Please make a copy of important data. We assume no responsibility for the data
loss.
●This manual has been carefully revised. Please contact our service center when
any type mistake is found.
●Please read the operating instruction carefully and use the accessories only
provided by the original factory to avoid any unexpected damage. No warranty
will be executed if you are not following the instruction or connecting with the
incompatible accessories. We assume no responsibility for any loss and damage
caused hereby.
●Any discrepancy between the pictures and real products hereinafter, the real
one prevails.
User's Manual
Chapter One: Product Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.4 Front buttons operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter Two: Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 How to install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Special bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 How to wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter Three: Adjustable Guide Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 About guide line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 What is the regular guide line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 How to adjust the guide line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter F : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .our 11 Menu Setting
4.1 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2 Menu setting guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter Five: Built-In Miracast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 How to connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2 Channel switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter Six: Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table of Contents

Chapter One: Product Introduction
1.3 Specifications
The packing box contains the following accessories. Please confirm:
7.3 inch car rear view mirror monitor with mirror link
Wire harness
User's manual
Wire cover
Remote control
Please check your package box for the items listed above. Please contact the
distributor or the agent as soon as possible if there is any damage.
1.1 Package
●
●
●
●
●
7.3 inch wide LCD display screen
2-way video inputs
Back-up camera display
Automatic brightness adjustment
4.0 mm glass and 21 mm car factory OEM bracket
Adjustable guide line
Mode switch between wide screen and dual screen LCD display separately
1.2 Features
●
●
●
●
φ
●
●
Screen size: 7.3 inch
Display screen: TFT-LCD
Aspect resolution: 1280(H)*390(V)
Working voltage: 12V
Working temperature: -20℃~+65℃
Signal system: PAL/Auto/NSTC
●
●
●
●
●
●
●
1.4 Front buttons operation
7.3 inch ultra high brightness display screen
1
Turn on/off the display screen ( reversing mode: short press to
adjust the screen brightness)
Indicator
1
2
3
4
5
6
7
2 3 4
7
6
5
Front light sensor
1 2
Press”M” button to switch back and forth between Android mode and iOS mode
built-in miracast mode switch
Press”CH” button to switch back and forth among 7 display modes: miracast,
Video+miracast, miracast+video, camera+miracast, miracast+camera, video full
display, camera full display.
Switch display mode
Pressing this button shortly can adjust the color mode of the image. Four modes
are available-- -standard, bright, beautiful, and soft.
Color mode adjustment

3 4
8
9
10
11
12
14
15
16
Speaker
Special bracket
8
9
10
11
12
13
14
15
16
17
Red to ACC+
Black to GND
Back car signal
Video input
Camera
Connector
Connector cover
17
8
18
Cable cover
13
18
Trigger line 1

2.1 How to install
Remove the original rear view mirror and remain
the metal based on the windscreen
Original car rear view mirror
Install rear view mirror along
this direction.
Install rear view mirror along
this direction.
Install rear view mirror along
this direction.
contrarotate the fixed
rear view mirror
1
Many kinds of brackets are available. Please find the one that suits your vehicle.
Please contact us if you could not find the bracket of your car here.
2.2 Special bracket
5 6
Chapter Two: Installation and Wiring
Different cars have different brackets. It depends on your vehicle maker and
manufacturer.
There are many methods to remove the original rear view mirror. However, please
don’t force the mirror off the bracket.
The manufacturer will not be responsible for any damage caused to your car by
wrong installation of the mirror.
Remove the original mirror
Install mirror monitor on the base

2.3 How to wire
3M
7 8
power harness
PUSE
BOX Black to GND
Red to ACC +12V
Black to GND
Red to ACC +12V
Black to GND
Red to ACC +12V
Back up video
Left video
The advisable installation
position for camera
Back up video
The reversing signal is input to rear view mirror by connecting the green line.
Therefore, reversing video can be displayed automatically on the wide 7.3 inch
LCD monitor.
Left video
green Back car singal
Trigger line 1
purple

UP Clockwise
Down
Right
left
Move the guide line Rotate the guide line
anti-clockwise
Press the button to choose L or R adjustable guide line.
Remote control
RL
Wrongposition
Right position
9 10
According to the site of standard reference line, we can put reference objects such
as desks in the back side of the car. Compared with the marked reference objects,
we can adjust the sites and angles of two guide lines are displayed on the monitor.
You will get the accurate and safety guide lines once it coincide with the reference
objects.
Press setting button to enter “guide line adjustment” mode. The system is
defaulted to adjust left guide line firstly. Press the button again to switch to adjust
the right guide line. The up , down left and right buttons are to
adjust the corresponding location of guide lines. The clockwise rotation and
contra rotating buttons are to adjust the angles of guide lines. It is easy to
operate and calibrate. After finishing calibration, switch the reverse gear to save
the information.
Caution: keep the remote control 0.5m-1.0m away from rear view mirror when you use the remote
to adjust the parking lines.
3.3 How to adjust the guide line
Displayonthemonitor
There are three lines---red, yellow, and green, to help drivers estimate the
distance from obstacles. Those three lines are displayed on the monitor when
the car is reversing. The green line is 10 feet away from the back of the car, and
the yellow line is 6.5 feet away. The distant red line is 3.3 feet away from the
back of the car, while the closed red line is 1.3 feet away. Please note that there
is 0.65 feet distance from the car for reference lines shown below.
3.1 About guide line
Regular guide lines are fixed although installation sites of camera and car size are
different. The fixed guide line is not accurate enough for drivers. There is huge
difference between the regular, fixed guide lines, and real guide lines of the car.
It may cause accidents when camera is mounted on the left or right side on the
back side of the car.
3.2 What the regular guide line is
Chapter Three: Adjustable Guide Line
7.8 inch
7.8 inch

11 12
Chapter Four: Menu Setting
Enter picture menu
Guide line clockwise
Menu parameter decreases
Menu parameter increases
Guide line up
Guide line left
Enter guide line
adjustment
Guide line anti-clockwise
Guide line right
Guide line down
Press to reset all
menu and parameters
4.1 Remote control
The menu only can be set by remote control, and kindly check its definition as below.
4.2 Menu setting guidance
Short press “MENU”to enter “PICTURE”, then you can switch between
“BRIGHTNESS”, “COLOR”, “CONTRAST”, “SCALE”, “START LOGO”, “PRESET”,
or enter out. When it switches to “PRESET”, re-press shortly the MENU, and
you would close the menu. UP and DOWN are to change the figure of each
setting.
4.2.1 BRIGHTNESS ADJUSTMENT
The defaulted setting is 50, ranging from 0 to 100, and only CVBS signal can work.
4.2.2 COLOR ADJUSTMENT
The defaulted setting is 50, ranging from 0 to 100, and only CVBS signal can work.
4.2.3 CONTRAST ADJUSTMENT
The defaulted setting is 50, ranging from 0 to 100, and only CVBS signal can work.
4.2.4 SCALE ADJUSTMENT
Turn on/off the adjustable guidelines.

4.2.6 PRESET ADJUSTMENT
4.2.5 START LOGO ADJUSTMENT
It is defaulted as OFF, and ON is to pre-set the menu, then it switches to OFF
automatically.
It is defaulted as “ON”, you can set it to “OFF” manually.
13
Chapter Five: Built-In Miracast
This is a special device to project your mobile phone to rear view mirror
monitor through Wi-Fi connection, and the popular standards like DLNA,
Miracast and Air Play. The driver can set the navigation path on the phone
before entering the car. The navigation audio and video can be displayed
simultaneously on the rear view mirror as long as the Wi-Fi is connected to
the rear view mirror. While driving you can also set navigation path by a
passenger using a mobile phone, the image is displayed simultaneously on
the rear view mirror.
5.1 How to connect
1: Make sure android phone has wireless projection function ( part of the
phone can not support wireless projection, or part of the phone wireless
display needs to root and could use after changing the system file).
2: Click the “M” button on the TP button, switch wireless mode to Android
mode; open the Wi-Fi on your phone, then search equipment in the phone's
wireless projection function, connect the device according to the wireless
device names that are displayed on the screen. Please see the steps as
below,
“M”button
14
4.2.7 VOLUME ADJUSTMENT
The defaulted setting is 80, ranging from 0 to 100, and only CVBS signal can work.
5.1.1 How to connect with Android phone (Android version has more
functions on how to use wireless projection. Please see your phone
instructions for reference. )
Please note: Make sure to turn of the bluetooth when you use miracast
function and connect your phone！

WIFI name
tap here
tap here
15 16
After finishing the connection, then the phone screen is projected to the
rear view mirror, you can press “CH” on TP button to choose "double mobile
dual mode" or "single-screen mode".
“M”button
1: Click the “M” button on TP button, switch the wireless mode to iOS mode.
5.1.2 How to connect with iPhone
2: Using iPhone search Wi-Fi (Wi-Fi name is displayed on the screen and
shown as below), then enter the default password: 12345678. After
finishing WIFI connection, bring up the shortcut menu, click on the AirPlay
function, select the device name, and open the mirroring.
tap here
Tap here
Turn it on
Tap here

17 18
5.2 Channel switching
5.2.1 Full CAMERA screen display
5.2.2 Full VIDEO1 screen display
After finishing the connection, then the phone screen is projected to the
rear view mirror, you can press “CH” on TP button to choose “double mobile
dual mode”or “single-screen mode”.
Press the “CH” button on the screen to switch display among CAMERA,
VIDEO1, MOBILE, VIDEO1+MOBILE, MOBILE+VIDEO1, CAMERA+MOBILE,
and MOBILE+CAMERA.
5.2.3 Full MOBILE screen display

5.2.4 VIDEO1 and MOBILE display simultaneously
5.2.5 CAMERA and MOBILE display simultaneously
19 20
Please note:
1. Both Reversing mode and non-reversing mode have seven states: built-in miracast, video+built-in miracast,
built-in miracast+video, camera+built-in miracast, built-in miracast+camera, full video screen, and full camera
screen.
2. Power on each time, the screen automatically keep the last status before the shut down. There are total eight
states or styles---seven are listed as above, and off-screen state.
3. There are three modes of operation can trigger video；
1) The first grade is +12V BACKUP LIGHT: You can adjust the seven states when there is signal of triggering
reversing through touching CH button. The final state will be stored after powering off, and the final state
will be shown automatically when there is trigger BACKUP LIGHT next time;
2) The second grade is +12V VIDEO CONTROL-- Video channel triggered line, which connects the turning light
or brake light in a general way. Mirror will switch automatically to full screen mode of VIDEO when the trigger
signal appears; while it will switch automatically to previous state when the trigger signal disappears after 3
seconds, in VIDEO trigger state: the only brightness button of TP buttons can work, while button of M and CH
don't work.
4. When the camera and mobile show at the same time, guide line can't be displayed.

Chapter Six: Firmware Update
1. click the “M” button on TP button, switch the wireless mode to iOS mode.
3. Tap “Scan” and follow the instructions to connect to Wi-Fi AP which allows to access
Internet through WAN. Please note that when the connection between dongle and AP
is established, the connection between dongle and mobile phone/laptop/table may be
disconnected. The reason is that the connection channel between dongle and mobile
phone is different from the channel between dongle and AP. In this case, mobile phone
/laptop/tablet should be connected to dongle by using soft AP again.
4. Dongle is able to access Internet through AP. AP's SSID and dongle's IP address
that are dispatched from AP (“Device IP1”) will be shown on the screen. The
mobile phone/laptop/tablet that is connected to dongle allows to access the
Internet because of AP bridge function of dongle.
Then long press “M” button to upgrade within 30 seconds.
21 22
“If new iOS releases, VTW73M may require new firmware update for Miracast
function. Availability of New firmware update may take awhile after Apple's
released new iOS.”
2. 1) using mobile/laptop/table search Wi-Fi (Wi-Fi name is displayed on the screen),
then enter the default password: 12345678.
2) Upon the connection between mobile/laptop/table and dongle is completed, open
web browser on the mobile phone/laptop/tablet.
3) Tap the icon to make the web browser jump to another page.
WIFI name
5. After upgrade is completed, restart the mirror.
BOYO products are consistently at the forefront of technology and innovation. Looking for cameras and driver safety? Visit our website.