B+K precision USB2RS User manual

Welcome to use our product
Installation Guide
Step 1: Insert CD Driver of this product to the CD-ROM
Step 2: Connect the device to a spare USB port on your PC , and find new hardware wizard,
please refer to the following chart:
Step 3: Select “No,not this time”,click “Next” to continue.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 4: Select “Install from a list or specific location(Advanced)”,click “Next” to continue.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 5: Select “Search removable media(floppy,CD-ROD…)”, click “Next” to continue.
Step 6: Auto search for the corresponding driver in the CD.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Setp 7: You will find two types of hardware wizard, one is for USB 2.0 TO RS232
Converter,another one is for USB 2.0 TO RS232 cable.please choose the corresponding
driver according to your product ,click “Next” to continue.
Step 8: The wizard has started insllation and copy file to your system
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 9: Click “Finish” to close the wizard.
Step 10: Find new com port.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 11: Select “No,not this time”,click “Next” to continue.
Step 12: Select “Install from a list or specific location(Advanced),click “Next” to continue.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 13: Select “Search removable media(flappy,CD-ROM…)”,click “Next” to continue.
Step 14: Auto search for the corresponding driver in the CD.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Setp 15: Choose one type of the driver for your product ,click “Next” to continue.
Step 16: The wizard has started insllation and copy file to your system .
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 17: Installation completed , click “Finish” to close the wizard.
Step 18: Your new hardware is installed and ready to use.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 19: If you want to see it, right click “ my computer” , then click “Properties”.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step 20: Select “Device Manager” in the “Hardware” of the interface “System Properties”, click
it, you can see the hardware devices installed on your computer , please refer to the following
chart :
Step 21: Installation finished .
Remarks:
After installation , if you can see “USB Serial Converter” from the “Device
Manager” ,but can’t see “USB Serial Port(COM3)” , please continue next steps.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step A: Right click “USB Serial Converter”, then click “Properties”.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Step B: Select “Load VCP” in the “Advanced”, click “OK”.
Step C: Move out USB TO RS232 on your computer. Connect the device to an old USB port on
your PC again, now it’s ok , please refer to the following chart:
Congratulations, installation is successful.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

Remove Driver
1, Open the drivers of this product , please refer to the below chart :
2，Double click “FTClen.exe”, it appears the following interface
3，click “Clean System”, it appears the following interface：
4，Disconnect USB 2.0 To rs232 device from the pc，click “ok”it appears the following
interface,then click“Yes＂
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

5, please click “No” to uninstall driver
6, When Uninstall is completed, please click “Exit” to terminate the uninstall
application.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30