Digitus DN-95109 User manual

Gigabit Ethernet PoE++
Injector, 802.3bt, 85 W
User Manual
DN-95109

2
Contents
1. Introduction ................................................................................. 2
2. Features ....................................................................................... 3
3. Hardware Description ................................................................... 4
4. Installation ................................................................................... 5
5. Troubleshooting ........................................................................... 5
6. Specifications ............................................................................... 7
Package content:
•Gigabit Ethernet PoE++ Injector, 802.3bt, 85 W
•Cable for non-heating appliances (safety plug / jack IEC 5)
•Quick reference guide
1. Introduction
The 802.3bt injector from DIGITUS® offers an 85 watt PoE port as a
midspan solution. Compact, cost-effective and fully IEEE802.3bt-
compliant. The simple solution for remote power supply of wireless
access points, IP security camera, VoIP phones, thin clients and other
installations with PoE functionality. PoE+/PoE++ compatible devices can
be supplied with power and data using the network cable, a secure and
reliable solution for expanding the existing network infrastructure. The
injector detects various PoE modes (A/B)- Plug & Play.

3
2. Features
Here are the features of 85W injector:
•Power over Ethernet Injector for 10/100/1000BaseT
•Full IEEE802.3at /bt compliant
•Automatically detects and protects PoE equipment from being
damaged by incorrect installation
•Internal AC/DC converter. No need for external power brick
•Overload and short circuit protection
•Mixes Ethernet and power into RJ-45 port
•Remote power feeding Delivers
•Power up to 100 meters
•Light weight and compact size
•Wall-Mountable design
•Easy Plug-and-Play installation
•Power over Ethernet output power of 56V@1.5A

4
3. Hardware Description
1. AC Power Input Connector:
This connector connects the AC power source to the PoE Injector.
2. Data IN:
This port is an RJ-45 Ethernet connector where data is received and
transmitted through the PoE Injector.
3. PoE OUT:
This port is an RJ-45 Ethernet connector where data is received and
transmitted through the PoE Injector and provides PoE power along
with the Ethernet data to a PoE device.
4. Alt A LED:
This LED indicates the pins 1/2/3/6 is providing power to the PoE OUT
port or not.
5. Alt B LED:
This LED indicates the pins 4/5/7/8 is providing power to the PoE OUT
port or not.
6. Ground Wire:
Please connect the ground wire

5
4. Installation
Before placing the Unit:
•Do not to cover PoE Injector or block the airflow to the PoE with any
foreign objects. Keep the PoE Injector away from excessive heat and
humidity and free from vibration and dust.
•Ensure that the cable length from Ethernet network source to the
terminal does not exceed 100 meters The PoE is not a repeater and
does not amplify the Ethernet data signal.
•Use a splitter if desired; ensure that the splitter is connected close to
the terminal and not on the PoE Injector.
•No "on-off" switch exists; simply plug the PoE Injector into an AC
power source.
Installing the Unit:
•Connect the PoE Injector to an AC outlet (100-40VAC), using a
standard power cord.
•Connect the Data IN jack (input) to the remote Ethernet network
switch’s Patch panel and the PoE OUT jack (output) to the terminal.
5. Troubleshooting
PoE Injector dos not power up:
•Verify that a reliable power cord is used.
•Verify that the voltage at the power inlet is between
100 and 240 VAC.
•Remove and re-apply power to the device and check the indicators
during power up sequence

6
The PD does not operate:
•Verify that the PoE Injector detects a PD.
•Verify that the PD is designed for PoE operation.
•Verify that you are using a standard Category 5/5e/6,
straight-wired cable, with four pairs.
•If an external power splitter is in use,
replace it with a known-good splitter.
•Ensure input Ethernet cable is connected to the DATA IN port.
•Verify that the PD is connected to the Data & Power port.
•Try to reconnect the same PD into a different PoE Injector.
If it works, there is probably a faulty port or RJ45 connection.
•Verify that there is no short over any of the twisted pair cables or
over the RJ45 connectors.
The end device operates, but there is no data link:
•Verify that the port indicator on the front panel is continuously lit.
•If an external power splitter is in use,
replace it with a known-good splitter.
•Verify that for this link, you are using standard UTP/FTP Category 5
straight (non-crossover) cabling, with all four pairs.
•Verify that the Ethernet cable length is less than 100 meters from the
Ethernet source to the load/remote terminal.
•Try to reconnect the same PD into a different PoE Injector If it works,
there is probably a faulty port or RJ45 connection

7
6. Specifications
Description
Interfaces
1 x RJ-45 Connector for Data
1 x RJ-45 Connector for PoE out + Data
Indicators
PoE: Alt A, Alt B
Standard
IEEE802.3af, IEEE802.3at, IEEE802.3bt
Power Method
100-240VAC, 50/60Hz
Output Voltage
56VDC
Power Supply
90W
PoE Budget
85W
Output PoE Pin Assignment
Alternative A:
V+ (RJ45 Pin3,6), V- (RJ45 Pin 1,2)
Alternative B:
V+ (RJ45 Pin4,5), V- (RJ45 Pin 7,8)
Dimensions
180 x 65 x 40 mm
Weight
0.6KG
Operating Temperature
0 to 40°C
Storage Temperature
-10 to 70°C
Operating Humidity
5 to 95% Noncondensing
Pack list
PoE Injector
1 pcs
User Manual
1 pcs
This is a Class A product. In home environment, this product may cause radio interference. In this
case, the user may be required to take appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the
shipping content. If the Declaration of Conformity is missing, you can request it by post under the
below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany