Braeburn 7320 User manual

7320
Universal Programmable Smart Wi-Fi Thermostat
For Systems Up to 3 Heat / 2 Cool
with Wireless Humidity Control*
User Manual
To prevent damage to the thermostat, never use a sharp instrument to
press the touchscreen keys. Always press keys with your fingers.
Attention
Read all instructions before proceeding
Store this manual for future reference
7320-110-01
®
* Wireless Humidity Control requires wireless remote humidity sensor.
See Wi-Fi Setup Guide for Wi-Fi Setup Instructions
TM

Contents
1 About Your Thermostat
Thermostat Features ................................................3
Thermostat and Display ........................................... 4
Thermostat TouchPads..............................................6
2 Setting User Options
Advanced User Options ............................................ 8
Table of User Options ............................................... 9
Audible Tone ............................................................11
Service Monitors (Filter, UV and Humidifier Pad) .........11
Extended Hold Time Period ......................................11
Temporary Override Adjustment Limit .....................12
Program Override Time Limit ..................................12
Thermostat Lock Code ........................................... 12
Wi-Fi Clear .............................................................13
3 Setting Your Program Schedule
Setting the Time and Day ....................................... 13
Tips Before Setting Your Program Schedule ........... 14
Programming a 7 Day Residential Schedule ........... 17
Programming a 5-2 Day Residential Schedule ........ 19
Programming a 7 Day Commercial Schedule ......... 20
4 Operating Your Thermostat
Setting the SYSTEM Control Mode ........................22
Setting the FAN Control Mode .............................. 23
Setting the Temperature .......................................24
Status Indicators ..................................................25
Wireless Sensor Status Indicators ........................ 26
Program Event Indicator .......................................28
Resetting the Thermostat .....................................28
5 Additional Operation Features
Auto Changeover Mode ....................................... 29
Adaptive Recovery Mode ..................................... 30
Circulating Fan Mode .......................................... 30
Programmable Fan Mode .....................................31
Compressor Protection ........................................ 31
Locking and Unlocking the Thermostat................. 32
AC Power Monitor ............................................... 34
Indoor Remote Sensing ....................................... 34
Outdoor Remote Sensing .................................... 35
Humidification and Dehumidification.................... 36
6 Thermostat Maintenance
Screen Cleaning .................................................. 38
Battery Replacement ........................................... 39
User Manual 2

Congratulations! You are in control of one of the easiest-to-use smart Wi-Fi thermostats on the
market today. This thermostat has been designed to provide you with years of reliable performance
and comfort control.
Features
• OptionalWi-Ficonnectivity–controlandmonitorthermostatfromasmartphone,tabletorcomputer
• 7day,5-2dayornon-programmable
• Large6.5sq.in.brightbluebacklitdisplayiseasytoread
• Autoormanualchangeover
• Residentialorcommercialmodes
• Adjustabletemperaturelimits
• Auxiliaryheatfossilfueloption
• Precisetemperatureaccuracykeepsyouincontrolofyourcomfort
• Convenientprogrammableandcirculatingfanmodes
• Optionalindoororoutdoorremotesensing(wiredorwireless)
• Optionalwirelesshumiditycontrol
3 User Manual

To prevent damage to the thermostat, never use a sharp instrument to press
the touchscreen keys. Always press keys with your fingers.
Attention
1
About Your Thermostat
User Manual 4
INSTRUCTIONS
HUMID
1
2
3
11
4
16
7
6
8
15
9
10
12
14
5
13

5 User Manual
Thermostat and Display
Room Temperature ...................... Displays the current room temperature
Lock Mode Indicator ................... Indicates if the thermostat is locked
Set Temperature .......................... Displays the current set point temperature
Service Indicators ...................... Displays various service/maintenance information
Humidity Indicator ....................... Indicates when there is a call for humidification
or dehumidification
Time of Day ................................. Displays the current time of day
Program Event Indicator..............Displays the program event
Day of the Week........................... Displays the current day of the week
System Status Indicator ............. Displays information about the status of the system
Hold Mode Indicator ................... Indicates if the thermostat is in HOLD mode
Low Battery Indicator.................. Indicates when the batteries need to be replaced
Wi-Fi/Wireless Indicator.............. Indicates when connected to Wi-Fi/wireless (flashes
when connection has been lost)
Fan Indicator................................ Indicates when the system fan is running
Quick Reference Instructions...... Stored in slot located at top of thermostat
SpeedBar®................................... Increases or decreases settings (time, temperature, etc.)
Reset Button ............................... Resets current time, program and user settings
Battery Compartment ................. Located in the back of thermostat
1
2
3
4
5
6
7
8
9
10
11
14
15
16
12
13

INSTRUCTIONS
HUMID
User Manual 6
1
About Your Thermostat
TouchPads
To prevent damage to the thermostat, never use a sharp instrument to press
the touchscreen keys. Always press keys with your fingers.
Attention

7 User Manual
Thermostat TouchPads
NOTE: Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are
the “touch sensitive” segments used to adjust your thermostat. Depending on equipment installed, all touchpads
may not show.
SYSTEM.....Selects AUTO (Heat/Cool), COOL, OFF HEAT or EMER (Emergency Heat)
FAN............Selects AUTO, ON, CIRC (Circulation) and PROG (Program) fan modes
PROG......... Selects programming mode or press for 3 seconds to select SpeedSet
®
mode
HOLD......... Enters/exits the HOLD mode (Program bypass)
DAY/TIME.. Sets the current time and day of the week
BACK......... Moves back in setting modes
NEXT..........Moves forward in setting modes
RETURN..... Returns to normal mode from program or settings modes
CONFIG...... Enters the User settings mode
HUMID*......Displays or adjusts the current humidity level
Outdoor Temperature
If an outdoor temperature sensor was connected, you may touch the room temperature area of the screen to
view the outdoor temperature.
*Only available if optional wireless remote humidity sensor is installed.

User Manual 8
2
Setting User Options
Advanced User Options
User options allow you to customize some of your thermostat’s features.
Most users will not need to make any changes to the settings
in this section.
To access the User Options menu, touch and hold the CONFIG
TouchPad for approximately 1 second until the screen changes
and displays the first User Option.
Press the SpeedBar
®
up or down to change the setting for the
displayed User Option. After you have changed your desired
setting, touch NEXT to advance to the next User Option. You may
also touch BACK to move backwards through the User Options.
When your changes are complete, touch RETURN to exit.
HUMID

Table of User Options
No. User Options Factory Setting Comments Pg.
Default Options
1 Audible Tone on BEEP on BEEP Enables an audible key press beep and comm loss beep.
oF BEEP
Disables an audible key press beep and comm loss beep.
2 Filter Service OFF OFF Disables filter service monitor feature.
Monitor 30, 60, 90, Selects a number of days that must pass before the
120, 180, 365 thermostat will flash a Service Filter reminder
in the display screen.
3 UV Light Service OFF OFF Disables UV service monitor feature.
Monitor 180, 365 Selects a number of days before the thermostat will
flash a Service UV reminder in the display screen.
4 Humidifier Pad OFF OFF Disables pad service monitor feature.
Service Monitor 180, 365 Selects a number of days before the thermostat will
flash a Service Humid reminder in the display screen.
5 Extended Hold Period LONG LONG Selects long (permanent) hold mode.
24HR Selects 24 hour (temporary) hold mode.
6 Temporary Override 0 ADJ 0, 1, 2, or 3 Selects a temporary temperature adjustment limit of
Adjustment Limit ADJ 00 (disabled), 1˚, 2˚ or 3˚.
NOTE: Some user options may not be available, depending on how your thermostat was configured in the
Installer Settings (see Installer Guide). A detailed description of each User Option follows this table.
11
11
11
11
11
12
9 User Manual
(continued)

Table of User Options
No. User Options Factory Setting Comments Pg.
Default Options
7 Program Override 4 TEMP 4, 3, 2 or 1 Selects a temporary program override time limit of
Time Limit TEMP 1, 2, 3 or 4 hours.
8 Thermostat Lock Code 000 0-9 Select a 3 digit lock code of 0-9 for each digit.
9 Wi-Fi Clear WIFI WIFI No changes to Wi-Fi network settings.
CL WIFI Clears Wi-Fi network settings.
NOTE: Some user options may not be available, depending on how your thermostat was configured in the
Installer Settings (see Installer Manual). A detailed description of each User Option follows this table.
12
13
User Manual 10
12

Detailed Explanation of User Options:
Audible Tone
User Option 1
The Audible Tone feature turns on or turns off a tone you will hear when you touch any of the TouchPads or press
the SpeedBar
®
. You will also hear an audible warning (beep) every 60 seconds during a Wi-Fi or wireless remote
sensor communication loss (see page 26). Select between on and off.
Service Monitors
(Filter, UV and Humidifier Pad)
User Options 2, 3 and 4
There are three user selectable service monitors that will display
reminders for a required air filter, UV bulb or humidifier pad
replacement. The SERVICE segment flashes in the display
along with FILTER, UV or HUMID. When the service interval
has been reached, and required cleaning or replacement has
been performed, touch the RETURN TouchPad to reset the
timer. Select OFF or a set number of days before the reminder
will appear.
Extended Hold Period
User Option 5
The Extended Hold Period lets you select the period your thermostat will hold the temperature when the HOLD
mode is activated (See Setting the Temperature, page 24). When LONG is selected the thermostat will hold your
temperature indefinitely. When 24HR is selected, the thermostat will hold your temperature for 24 hours and
HUMID
Service
Reminders
11 User Manual

Temporary Override Adjustment Limit
User Option 6
The Temporary Override Adjustment Limit will limit how
much the temperature can be adjusted from the current set point
when the thermostat is used in the programmable mode. This
setting will not allow the user to override the temperature past
the selected limit amount of 1, 2 or 3 degrees from the current
set point. When the user reaches the adjustment limit the screen
will flash ADJ. A setting of 0 disables the adjustment limit.
The Temporary Override Adjustment Limit can also be used in
the non-programmable mode if the keypad lockout security
level is set to level 1 (See Installer Guide).
Program Override Time Limit
User Option 7
The Program Override Time Limit allows you to set a maximum time limit (in hours) that the thermostat will
return to the program after a temporary temperature adjustment has been made (See Setting the Temperature,
page 24). You may select 1, 2, 3 or 4 hours. Not available in non-programmable mode.
Thermostat Lock Code
User Option 8
The Thermostat Lock Code sets a 3-digit code that you may use at any time to lock or unlock the thermostat.
Setting the code in the user options mode does not activate the lock feature (See Locking/Unlocking Thermostat,
page 32). You may choose a 3-digit code with each digit being 0-9.
HUMID
User Manual 12

Setting the Time and Day
1. In normal operating mode, touch the DAY/TIME TouchPad.
The display will switch to the day/time setting mode and the
hour will be flashing.
2. Press the SpeedBar®up or down to adjust the hour,
touch NEXT.
3. Press the SpeedBar up or down to adjust the minute,
touch NEXT.
4. Press the SpeedBar up or down to adjust the day of the week.
5. Touch RETURN to exit.
NOTE: If the Wi-Fi feature is used, the clock will adjust automatically to the time zone and DST (Daylight Savings
Time) set up in the Wi-Fi feature.
3
Setting Your Program Schedule
Wi-Fi Clear
User Option 9
Use this setting if you no longer want to be connected to your Wi-Fi network or if you change Wi-Fi routers.
Select WIFI to skip changes to your network settings. Select CL WIFI to clear all Wi-Fi network settings. You can
set up Wi-Fi again at a later time if desired (see Wi-Fi Setup Guide).
13 User Manual

Tips Before Setting Your Program Schedule
• Makesureyourcurrenttimeanddayoftheweekaresetcorrectly.
• Whenprogramming,makesuretheAMandPMindicatorsarecorrect.
• Variousinstallersettingssuchasautochangeovermode,fanlockmodeandtemperatureadjustmentlimits
may affect your programming flexibility.
• Your NIGHT event cannot exceed 11:50 p.m.
This thermostat has been configured with one of the following programming options:
• Residential7dayprogrammingmodewith4eventsperday(default)
• Residential5-2(weekday/weekend)programmingmodewith4eventsperday
• Commercial7dayprogrammingmodewith2eventsperday
• Non-Programmablemode
NOTE: If this thermostat was configured In the Installer Settings to be non-programmable, then you cannot set a
user program and may skip this section. See the Installer Guide for different configuration options.
(Program changes can be made at the thermostat or from the BlueLink Smart
ConnectTM application on your smartphone, tablet or PC.)
User Manual 14

Energy Saving Programs
This thermostat comes pre-programmed with a default energy saving program. The following tables outline
the pre-programmed times and temperatures for heating and cooling in each of your 4 daily events (2 events if
configured for commercial mode). If you wish to use these settings then no further programming is necessary:
MORN
DAY
EVE
NIGHT
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 78˚ F (26˚ C)
Time: 8:00 am
Heat: 62˚ F (17˚ C)
Cool: 85˚ F (29˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 78˚ F (26˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 82˚ F (28˚ C)
4 Event All Days
Residential 7 Day Programming
Factory Settings
Time: 8:00 am
Heat: 70˚ F (21˚ C)
Cool: 78˚ F (26˚ C)
OCCUPIED
UNOCCUPIED
Time: 6:00 pm
Heat: 62˚ F (17˚ C)
Cool: 85˚ F (29˚ C)
2 Event All Days
Commercial 2 Event Programming
Factory Settings
15 User Manual

Weekday Weekend
MORN
DAY
EVE
NIGHT
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 78˚ F (26˚ C)
Time: 8:00 am
Heat: 62˚ F (17˚ C)
Cool: 85˚ F (29˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 78˚ F (26˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 82˚ F (28˚ C)
4 Event
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 78˚ F (26˚ C)
Time: 8:00 am
Heat: 62˚ F (17˚ C)
Cool: 85˚ F (29˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 78˚ F (26˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 82˚ F (28˚ C)
Residential 5-2 Day Programming– Weekday/Weekend
Factory Settings
User Manual 16

Programming a 7 Day Residential Schedule
The 7 day residential programming mode gives you the option to program individual days (1 day at a time) or to
use SpeedSet and program the entire week (all 7 days) with a 4 event program schedule.
Setting All 7 Days at Once (SpeedSet
®
)
NOTE: Setting all 7 days at once will copy over any previously programmed individual days.
1. Hold the PROG TouchPad for 3 seconds. The display will
switch to SpeedSet programming mode. All 7 days of the
week will appear and the hour will be flashing.
2. Touch SYSTEM to select HEAT or COOL.
3. Press the SpeedBar®up or down to adjust the hour for
the MORN (morning) event. Touch NEXT.
4. Press the SpeedBar up or down to adjust the minute for the
MORN event. Touch NEXT.
5. Press the SpeedBar up or down to adjust the temperature for
the MORN event. Touch NEXT.
6. Press the SpeedBar up or down to adjust the fan setting for
the MORN event. Touch NEXT.
7. Repeat steps 3-6 for the DAY, EVE and NIGHT events.
8. If needed, repeat steps 2-7 to program the opposite mode (HEAT or COOL).
9. Touch RETURN to exit.
17 User Manual

Setting Individual Days (7 Day Residential)
1. Touch the PROG TouchPad. The display will switch to
programming mode. M (Monday) will be displayed and the
hour will be flashing.
2. Touch SYSTEM to select HEAT or COOL.
3. Touch DAY/TIME to select the day you would like to program.
4. Press the SpeedBar® up or down to adjust the hour for the
MORN (morning) event. Touch NEXT.
5. Press the SpeedBar up or down to adjust the minute for the
MORN event. Touch NEXT.
6. Press the SpeedBar up or down to adjust the temperature
for the MORN event. Touch NEXT.
7. Press the SpeedBar up or down to adjust the fan setting for
the MORN event. Touch NEXT.
8. Repeat steps 4-7 for your DAY, EVE and NIGHT events.
9. If needed, repeat steps 3-7 to select a different day to program.
10. If needed, repeat steps 2-9 to program the opposite
mode (HEAT or COOL).
11. Touch RETURN to exit.
User Manual 18

Programming a 5-2 Day Residential Schedule
The 5-2 day residential programming mode allows you to program Monday - Friday with one 4 event schedule
and then allows you to change Saturday and Sunday with a different 4 event schedule.
1. Touch the PROG TouchPad. The display will switch to
programming mode. The days M, TU, W, TH, and F will be
displayed and the hour will be flashing.
2. Touch SYSTEM to select HEAT or COOL.
3. Press the SpeedBar® up or down to adjust the hour for the
MORN (morning) event. Touch NEXT.
4. Press the SpeedBar up or down to adjust the minute for the
MORN event. Touch NEXT.
5. Press the SpeedBar up or down to adjust the temperature
for the MORN event. Touch NEXT.
6. Press the SpeedBar up or down to adjust the fan setting for
the MORN event. Touch NEXT.
7. Repeat steps 3-6 for your DAY, EVE and NIGHT events.
8. Repeat steps 3-7 for your weekend (S, SU) program.
9. If needed, repeat steps 2-9 to program the opposite
mode (HEAT or COOL).
10. Touch RETURN to exit.
19 User Manual

Programming a 7 Day Commercial Schedule
The 7 day commercial programming mode gives you the option to program individual days (1 day at a time) or to
use SpeedSet and program the entire week (all 7 days) with a 2 event program schedule.
Setting All 7 Days at Once (SpeedSet®)
NOTE: Setting all 7 days at once will copy over any previously programmed individual days.
1. Hold the PROG TouchPad for 3 seconds. The display will
switch to SpeedSet programming mode. All 7 days of the
week will appear and the hour will be flashing.
2. Touch SYSTEM to select HEAT or COOL.
3. Press the SpeedBar®up or down to adjust the hour for
the OCCUPIED event. Touch NEXT.
4. Press the SpeedBar up or down to adjust the minute for
the OCCUPIED event. Touch NEXT.
5. Press the SpeedBar up or down to adjust the temperature for
the OCCUPIED event. Touch NEXT.
6. Press the SpeedBar up or down to adjust the fan setting for the
OCCUPIED event. Touch NEXT.
7. Repeat steps 3-6 for your UNOCCUPIED event.
8. If needed, repeat steps 2-7 to program the opposite mode (HEAT or COOL).
9. Touch RETURN to exit.
User Manual 20