Braeburn Economy 2030 User guide

®
Installer Manual
Programmable Thermostats
1 Specifications 2 Installation 3 Wiring
4 Quick Reference 5 Installer Settings 6 System Testing
Possible electric shock or damage to equipment can occur.
Disconnect power before beginning installation.
Caution
2030 1 Heat / 1 Cool Conventional
or Heat Pump
2230 Up to 2 Heat / 1 Cool
Conventional or Heat Pump
Warning
For installation by experienced service technicians only.
This thermostat is compatible with:
• Single stage conventional and heat pump systems
• Single stage heat pumps with auxiliary heat
• 250 – 750 millivolt heating only systems
• 2 wire hydronic zone systems
Electrical and Control Specifications
• Electrical Rating: 24 Volt AC
• 1 amp maximum load per terminal
• AC Power: 18 – 30 Volts AC
• DC Power: 3.0 Volt DC
(2 “AA” Alkaline Batteries Included)
• Control Range: 45° to 90° F (7° to 32° C)
• Temperature Accuracy: +/- 1° F (+/- .5° C)
1
SPECIFICATIONS
2030-100-01
Model number is located on back of thermostat.
ECONOMY
SERIES
This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline batteries for
proper operation. When connecting 24 Volt AC Power, the batteries may be installed as a backup.
For use only as described in this manual. Any other use will void warranty.
Terminations
2030: Rc, Rh, W1, Y1, G, O, B, C
2230: Rc, Rh, W1/E, W2, Y1, G, O, B, L, C
This manual is for Installer use only - do not leave with end user.

Installer Manual 2
2
INSTALLATION
Thermostat Location
Install the thermostat approximately 5 feet (1.5m) above the floor in an area that has a good amount of air
circulation and maintains an average room temperature.
Avoid installation in locations where the thermostat can be affected by drafts, dead air spots, hot or cold air
ducts, sunlight, appliances, concealed pipes, chimneys and outside walls.
Warning
Disconnect power before beginning installation.
Install the Sub-Base:
• Remove the sub-base from the body of the thermostat.
• Mount the sub-base as shown below:
Drill 3/16” pilot holes in your
desired location. Use supplied
anchors for drywall or plaster.
UP UP

3 Installer Manual
Provide Power
• Battery Power - Insert the 2 supplied “AA” type alkaline batteries into the battery compartment located
in the rear housing of the thermostat. Make sure to position the Positive (+) and Negative (-) sides of the
batteries correctly with the +/- symbols in the battery compartment.
• Optional 24 Volt AC power - Connect the common side of the transformer to the C terminal on the
thermostat sub-base. In dual transformer installations, the transformer common must come from the
cooling transformer.
C
24VAC Power Terminal (C) Batteries Installed as Shown
2
INSTALLATION
Factory Setting
Switch Default Options Comments
CONV / HP CONV
HG / HE HG
Set Installer Switches
CONV Select for conventional systems
HP Select for heat pump systems
HG Select for gas heat
HE Select for electric heat
The Installer switches are located on the back of the thermostat and must be
properly configured for this thermostat to operate properly.
Attach to Thermostat Sub-Base
UP UP
UP
Once you complete the wiring in Section 3, attach
thermostat to sub-base and then configure the
Installer Settings in Section 5.
1) Line up the thermostat body with the sub-base.
2) Carefully push the thermostat body against the
sub-base until it snaps in place.
NOTE: This thermostat ships configured as a
conventional (CONV) thermostat.

Installer Manual 4
Conventional and Heat Pump Systems - Typical Wiring Configurations
3
WIRING
CONVENTIONAL HEAT PUMP
Heat Only 1 Heat/ 2 Heat/ 1 Heat/ 2 Heat/1 Cool
or Millivolt 1 Cool 1 Cool 1 Cool (w/Aux Heat)
Wiring
Terminal
Rh 24 VAC Heating Transformer Rh Rh1Rh1Rh6 Rh6
Rc 24 VAC Cooling Transformer - Rc1,2 Rc1,2 - -
(W1) Conventional Heat Relay
(E) Emergency Heat Relay
2nd Stage Heat/Auxiliary Heat
Y1 Compressor Relay - Y1 Y1 Y1 Y1
GFan Relay G3G G G G
Cool Active Reversing Valve - - - O8O8
Heat Active Reversing Valve -- - B8 B8
L * System Malfunction Indicator - - - L9 L9
C24 VAC Transformer Common C4C4,5 C4,5 C10 C10
*2230 Only.
NOTES - Conventional Systems
1Remove factory installed jumper wire for dual transformer systems
2 Only required for dual transformer systems
3 Only connect if needed for system
4Optional 24 VAC transformer common connection
5For dual transformer systems, common must come from cooling transformer
Provide disconnect and overload protection as required.
NOTES - Heat Pump Systems
6Do not remove factory installed jumper wire
7If no separate emergency heat relay, connect to W2 and Install a field supplied jumper wire from W2 to E
8 Wire O for cool active valve or B for heat active valve (never both)
9If using optional L terminal, the 24 VAC common must be connected (C terminal)
10 Optional 24 VAC transformer common connection
Provide disconnect and overload protection as required.
Terminal Description
W1
W2*
O
W1
W1 -
E7
- -
W2
-
W27
W1/E
2030 / 2230 2230 2030 / 2230 2230
B
NOTE: Make sure installer system selection
switch is properly set to CONV or HP.
See Section 2.

CONVENTIONAL HEAT PUMP
Heat Only 1 Heat/ 2 Heat/ 1 Heat/ 2 Heat/1 Cool
or Millivolt 1 Cool 1 Cool 1 Cool (w/Aux Heat)
5 Installer Manual
4
QUICK REFERENCE
SYSTEM Switch.....................Selects the system you want to control
PROG Button..........................Enters programming mode or hold for 3 seconds to enter SpeedSet®mode
BACK Button*........................Secondary function of the PROG button - Moves to previous setting
HOLD Button..........................Enters / Exits the HOLD mode (program bypass mode)
NEXT Button* ........................Secondary function of the HOLD button - Moves to next setting
FAN Switch............................Selects the system fan mode
Up / Down Arrow Buttons.....Increases or decreases settings (time, temperature, etc.)
MENU Button.........................Used to access thermostat User / Installer setting modes
Room Temperature ..............Displays the current room temperature
Set Temperature .................. Displays the current setpoint temperature
Override Indicator ............... Indicates that the current program schedule has been temporarily overridden
Time of Day ..........................Displays the current time of day
Program Event Indicator ..... Indicates which part of the program is currently active
System Mode .......................Displays the system mode and current system status
Fan Mode Indicator ............. Indicates the current system fan mode
Fan Status Indicator ............Indicates that the system fan is running
Low Battery Indicator ......... Indicates when the batteries need to be replaced
Battery Compartment ...........Located on the back side of thermostat (if installed)
1
4
5
6
Thermostat and Display
1
5
2 3 4
6
7
8
9
10
11
12
13
14
15
*BACK and NEXT are secondary functions of the PROG and HOLD buttons. When in programming or
configuration modes, BACK and NEXT appear in the display screen indicating that the PROG and HOLD
buttons now function as BACK and NEXT.
2
3
7
8
10
12
15
13
14
11
9

Installer Manual 6
5
INSTALLER SETTINGS
The Installer Settings must be properly configured in order for this thermostat to operate correctly. The Installer
Settings are menu driven. The portion of these settings that do not apply to your setup will be skipped.
To Enter Installer Settings Menu
1 Press and hold down the MENU button for 5 seconds.
2Release the MENU button after the first installer
setting is displayed.
3
Change settings as required using the or buttons.
4Press NEXT (HOLD) or BACK (PROG) to move to the
next or previous setting.
5Press MENU to exit. Menu will exit automatically
after last setting.
*If 0000 IL is displayed, you must enter your 4-digit
installer lock code to proceed (see Installer Settings
11 and 12).
No. Installer Setting Displayed Default Available Description of
Setting Settings Available Settings
1 Programming Mode PROG 7
Selects the programming capabilities of the thermostat, either full 7 individual days, 5-2 day (weekday/weekend)
programming or non-programmable.
2Temperature Scale DEG F
Selects a temperature scale of either °F or °C.
31st Stage Differential DIF1 0.5
Selects a 1st stage temperature differential which controls the degree of separation between the setpoint temperature
and the 1st stage of heating or cooling.
42nd Stage Differential DIF2 2.0
[2230 only] Selects a 2nd stage temperature differential which controls the degree of separation between the 1st
and 2nd stage of heating or cooling.
5Compressor Short Cycle CSCP 5
Protection (CSCP)
Selects the number of minutes the compressor(s) will be locked out after turning off. This delay will run simultaneously with
any delay built into the equipment.
6Adaptive Recovery REC OF
Mode (ARMTM)
[Not available if non-programmable was selected in setting 1] During ARM, room temperature is recovered by turning
on the heating or cooling up to 3-hours before the end of the set back period. The setpoint temperature is changed to that
of the upcoming program temperature.
7 Select for 7-day programming mode
52 Select for 5-2 day programming mode
NO Select for non-programmable mode
F Select for Fahrenheit temperature display
C Select for Celsius temperature display
0.5, 1.0, 2.0 Select a 1st stage temperature differential of
0.5°, 1° or 2° F (0.2°, 0.5° or 1.0° C)
1.0, 2.0, 3.0 Select a 2nd stage temperature differential of
4.0, 5.0, 6.0 1°, 2°, 3°, 4°, 5° or 6° F (0.5°, 1.0°, 1.5°, 2.0°,
2.5° or 3.0° C)
5, 4, 3, Select CSCP delay duration in minutes
2, 1, 0
OF Adaptive Recovery Mode is disabled
ON Adaptive Recovery Mode is enabled

7 Installer Manual
5
INSTALLER SETTINGS
No. Installer Setting Displayed Default Available Description of
Setting Settings Available Settings
7Heat Setpoint HIGH HEAT 90
Upper Limit
Selects the upper setpoint adjustment limit that cannot be exceeded in heat mode.
8Heat Setpoint LOW HEAT 45
Lower Limit
Selects the lower setpoint adjustment limit that cannot be exceeded in heat mode.
9Cool Setpoint
LOW COOL 45
Lower Limit
Selects the lower setpoint adjustment limit that cannot be exceeded in cool mode.
10 Cool Setpoint HIGH COOL 90
Upper Limit
Selects the upper setpoint adjustment limit that cannot be exceeded in cool mode.
11 Installer Lock INST NO
When enabled, a 4-digit lock code can be entered in setting 12. This lock code will be required the next time the
Installer Settings menu is accessed. Select NO to skip the installer lock.
12 Installer Lock Code IL 0000
[Only available if Installer Lock was enabled in setting 11] Select a 4-digit lock code (0-9 for each digit) to
lock the Installer Settings menu. The code 0000 is not a valid lock code and cannot be used.
13 Installer Clear CLR NO
(factory reset)
Selecting Y (YES) will return thermostat to all factory default settings. Factory reset will take affect upon exiting
Installer settings menu.
90 - 45 Select a Heat Setpoint Upper Limit of 90° to
(32˚ to 7˚C) 45°F (32° to 7°C)
45 - 90 Select a Heat Setpoint Lower Limit of 45° to
(7˚ to 32˚C) 90°F (7° to 32°C)
45 - 90 Select a Cool Setpoint Lower Limit of 45° to
(7˚ to 32˚C) 90°F (7° to 32°C)
90 - 45 Select a Cool Setpoint Upper Limit of 90° to
(32˚ to 7˚C) 45°F (32° to 7°C)
NO Installer Lock disabled
Y Installer Lock enabled
0-9 Select 0-9 for each digit
NO Clear disabled - No changes made
Y Clear enabled - Factory Reset
Additional options such as Service Monitors, clock, etc. are located in the User Settings – See User Manual.

Warning
Read Before Testing
• Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system control board
to test the thermostat installation. This could damage the thermostat and void the warranty.
• Do not select the COOL mode of operation if the outside temperature is below 50º F (10º C). This could
possibly damage the controlled cooling system and may cause personal injury.
• This thermostat includes an automatic compressor protection feature to avoid potential damage to the
compressor from short cycling. When testing the system, make sure to take this delay into account.
NOTE: The compressor delay can be bypassed by adjusting Installer Setting 5 - See section 5.
1Move the SYSTEM switch to HEAT mode.
2Press the button to raise the set temperature a minimum of 3 degrees above the current room
temperature. The system should start within a few seconds. With a gas heating system, the fan may
not start right away.
3Move the SYSTEM switch to OFF mode. Allow the heating system to fully shut down.
4Move the SYSTEM switch to COOL mode.
5Press the button to lower the set temperature a minimum of 3 degrees below the current room
temperature. The system should start within a few seconds (unless compressor short cycle protection
is active – See note above).
6Move the SYSTEM switch to OFF mode. Allow the cooling system to fully shut down.
7Move the FAN switch to FAN ON mode. The system fan should start within a few seconds.
8Move the FAN switch to FAN AUTO mode. Allow the system fan to turn off.
6
SYSTEM TESTING
Limited Warranty
When installed by a professional contractor, this product is backed by a 5 year limited
warranty. Limitations apply. For limitations, terms and conditions, you may obtain a full
copy of this warranty:
• Visit us online: www.braeburnonline.com/warranty
• Call us: 866.268.5599
• Write us: Braeburn Systems LLC
2215 Cornell Avenue
Montgomery, IL 60538
55
YEAR
WARRANTY
LIMITED
Installer - store this manual for future reference
Braeburn Systems LLC
2215 Cornell Avenue • Montgomery, IL 60538
Technical Assistance: www.braeburnonline.com
Call us toll-free: 866-268-5599 (U.S.)
630-844-1968 (Outside the U.S.)
©2022 Braeburn Systems LLC • All Rights Reserved. 2030-100-01