Bratt Decor jane JN01 User manual

www.brattdecor.com
Model #
JN01-2
This crib con-
forms to the
standards of the
U.S. Product
Consumer Safety
Commission.
baby crib
“jane”

Mattress Positions:
Please use the following guidelines as set forth by the American Academy of Pediatrics to decide which level is appropriate for your child:
LEVEL (1) highest position To be used by newborns, until shortly before they can sit alone. Under no circumstances should the mattress support be
in its highest position after the child can sit.
LEVEL (2) middle position To be used by babies who can sit, until shortly before they can stand. Under no circumstances should the mattress sup
port be in the middle position after the child can stand.
LEVEL (3) lowest position The mattress support must be in it’s lowest position before the baby can stand.
Under no circumstances should the child be allowed to use this crib when they reach 35 inches tall.
All contents of these instructions are the sole property of Bratt Décor, Inc. and may not be reproduced in any way without the specific written agreement of Bratt Decor, Inc. Any violation of this will be prosecuted under the federal copyright laws.
LARGE COMPONENTS
A Left Head Board 1
B Right Head Board 1
C Back Piece 1
D Front Gate 1
EF
GE Mattress Support 1
F Stabilizer bars 2
G Casters 4
AB
C
D

Maintenance:
Once a week inspect the crib for any damaged hardware, loose joints, missing parts or sharp edges. Discontinue using the crib if any parts are
missing or broken, contact Bratt Decor, Inc. for replacement parts if needed. Cleaning: if crib is dirty, wipe with a cloth dampened with warm water.
Do not use solvents. Storage: store in a dry place.
Warning: If this crib is not purchased new, do not use it until you have contacted Bratt Decor, Inc. to find out if the crib conforms to the current safety
standards.
Place these assembly instructions and the hex tool in the bag provided on the mattress support. You will need these assembly instruc-
tions every time you assemble this crib.
FASTENERS
shown actual size
H
H Medium Machine Screw 4
I Wing Nut 4
J Long Machine Screw 8
K Short Machine Screw 4
L Small Machine Screw 2
M Plastic Bushing 2
N Metal Guide Pin 2
O Metal Cross Dowel 4
Tools required
P Hex Tool (provided) 1
Phillips Head Screwdriver
P
I
J
KM
N O
L

E
F
K
Attach the Mattress Support (E)
to the 2 Stabilizer Bars (F) using
the 4 short Machine Screws (K).
Tighten with the Hex Tool (P).
Note: the dowels protruding from
the ends of the Stabilizer Bars
must be on the bottom.
H
E
I
Position the Mattress Support Legs (Z)
as shown (follow the guide on the back of
these instructions for the correct height for
your child) and install the Medium Machine
Screw (H) and the wing nut (I). Tighten by
hand. Repeat on the remaining 3 Legs.
Highest mattress position.
Middle mattress position.
Lowest mattress position.
For more information on
the proper position for the
Mattress Support, please
refer to the back of this
page under the heading:
“Mattress Positions”
Under no circumstances
should the child be allowed to
use this crib when they reach
35 inches tall.
CAUTION:
Z
1
2

J
E
J
Attach the Left Head Board (A) and the Right Head Board (B) to
the Mattress Support assembly (from figure 2) using the 4 Long
Machine Screws (J) and the 4 Metal Cross Dowels (O). Do not
tighten these screws until you have completed step 4.
B
A
O
3

C
J1
J1
4
5
J
Attach the Back Piece (C) using
the 4 remaining Long Machine
Screws (J). Use the Hex Tool
(P) to tighten these screws.
Now tighten the 4 Long Machine
Screws shown as (J
1) using the
Hex Tool.
G
Install the Plastic Bushing
(M) using a Small Machine
Screw (L). Do not over
tighten. Now install the
Metal Guide Pin (N), and
tighten with a Phillips Head
screwdriver. Repeat this
installation on the right side
of the crib.
Install the Casters (G) by
pushing them firmly (until
they click into place) into the
mounting bushings on the
bottom of the legs.
N
M
L

Install the Front Gate (D) as shown.
Step 1: Using the Hex Tool, loosen the screw shown as (1) and separate the Head Board from the
Stabilizer Bar about 1/4” (only on one side).
Step 2: Place the Front Gate (D) at an angle as shown (making sure the sticker is on the underside of
the gate as indicated). On one side at a time, insert the Plastic Bushing (M) into the black plastic
channel on the side of the Front Gate (D). Repeat on the other side.
Step 3: Swing the bottom of the gate down and fit the Metal Guide pins (N) into the Plastic Slots on the
side of the Front Gate (D).
Step 4: Using the Hex Tool, tighten the screw (1) again.
Raising and lowering the gate:
To lock the gate into the top position, simply raise the gate until the mechanism engages.
To lower the gate, first lift the gate slightly, then, with your knee, push against the center of the bottom rail of the front gate while
simultaneously lowering the gate with your hand.
2
2
3
D
3
1
This sticker should not be removed.
If the gate is installed correctly, this
sticker should not be visible from
outside the crib.
CAUTION:
6

FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
* Read all instructions before assembling crib.
KEEP INSTRUCTIONS FOR FUTURE USE.
* Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing
parts or sharp edges. DO NOT use crib if any parts are missing or broken. Ask your dealer or
write to BRATT DECOR, INC. for replacement parts and instructional literature if needed. DO
NOT substitute parts.
* After raising side, make sure latches are secure.
* When child is able to climb out or reaches the height of 35” (90 cm), the crib shall no longer
be used.
* DO NOT place crib near window where cords from blind or drapes may strangle a child.
* If refinishing, use a non-toxic finish specified for children’s products.
* DO NOT leave child in crib with side lowered. Be sure side is in raised and locked position
whenever child is in crib.
* When child is able to pull to standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
* Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
* DO NOT use a water mattress with this crib.
It is extremely important to make sure all bolts and other fasteners are securely tightened and
checked for tightness at least once a week.
Strings can cause strangulation! Do not place items with a string around a child’s neck, such as
hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys.
ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES BY 51
5/8 INCHES WITH A THICKNESS NOT EXCEEDING 6 INCHES.
WARNING:
WARNING:
CAUTION:
CAUTION:
Bratt Decor, Inc. P.O.Box 20808 Baltimore, MD 21209 1 888 24 BRATT