Breitling BENTLEY SUPERSPORTS B55 User manual

BENTLEY
SUPERSPORTS B55

3. REGULARITY RALLY Chronograph:“Stage” version
STAGE 01
EARLY 01
TARGET
ACTUAL
STAGE 02
000
STAGE 03 STAGE 04
0
LATE 02 GOAL 03 EARLY 04
4. REGULARITY RALLY Chronograph:“Split” version
EARLY 01 EARLY 04LATE 02 GOAL 03
TARGET
ACTUAL
0
SPLIT 01 SPLIT 02 SPLIT 03 SPLIT 04
1. RALLY Chronograph
STAGE 01
SPLIT 1
of S01
STAGE 02
TIME S01 TIME S02 TIME S03 TIME S04
TOTAL RALLY TIME
0
STAGE 04
00
STAGE 03
0
Penalty times can be added on each stage and/or on the total rally time.
SPLIT 2
of S01
SPLIT 1
of S03 SPLIT 1
of S04
2. RACE Chronograph
LAP 01
LAP 02
LAP 03
LAP 04
SPLIT 1
of L01
TIME L01 TIME L02 TIME L03 TIME L04
TOTAL RACE TIME
0
SPLIT 1
of L02 SPLIT 2 of L02 SPLIT 1
of L03 SPLIT 2 of L03 SPLIT 1
of L04 SPLIT 2
of L04
SPLIT 2
of L01

BENTLEY
SUPERSPORTS B55
P1
P2

ENGLISH 5-82
ESPAÑOL 83-162
245-322
PORTUGUÊS 163-244
3
CERTIFICATIONS 323-326
Up-to-date user manuals are
available on breitling.com
under SERVICE section.

5
CONTENTS
1. General instructions
a) Reference time and timezones
b) Functions
c) User interfaces
d) Light intensity setting
e) “Parking” the hands
f) Blocking a function
g) Connecting the watch to a smartphone
2. Rechargeable battery and power management
a) Rechargeable battery
b) Power management
c) Battery charging
3. Initializing the watch
4. Adjusting the time base of the watch (UTC)
a) Setting (SET UTC)
5. Setting the date (SETDATE)
6. Setting the main timezone (TIME)
a) Setting (SETTIME)

76
g) Rereading intermediate times
h) Recovering times
i) Synchronizing the seconds hand
11. Lap timer chronograph (LAP TMR)
a) Recording several laps (LAP)
b) Synchronizing the seconds hand
c) Recovering times
12. “Rally cross” chronograph (RALLy)
a) Setting (SET RLy)
b) Timing a rally
c) Rereading a rally
d) Adding a penalty time
e) Deleting a stage
f) Introducing a fixed time
g) Erasing one or more rallies
h) Recovering times
13. Race track chronograph (RACE)
a) Setting (SETRACE)
b) Timing a race
c) Introducing a lap length
d) Rereading a race
7. Configuring the watch (SETTING)
a) SyNCHRO
b) TILT (ON or OFF)
c) LIGHT (SHORT, MEDIUM or LONG)
d) DISPLAy (DISP ON or DISPOFF)
e) NIGHT MODE (ON or OFF)
f) TONE (OFF, PUSH, PUSH+HR or PUSH+CH)
g) HANDPRK (5 MIN or DBLPRES)
h) MODE (RACING or SPORT)
i) CONNECT (ON or OFF)
8. Date display (DATE)
9. Alarms (AL1 to AL7)
a) Setting (SET ALx)
b) Use
10. Chronograph with intermediate/split times and tachymeter (CHR ADD)
a) Measuring a single time
b) Measuring a period with intermediate/split time(s) (SPLIT)
c) Flyback
d) Tachymeter
e) Converting units of speed
f) Introducing the distance for the tachymeter

98
17. Notifications received from a smartphone (NOTIFy)
a) Reading notifications
b) Setting notifications
18. Battery charging status (BATxx%)
a) DEEP SLEEP mode
b) SOFT SLEEP mode
19. In the event of problems
20. List of words in user interface
e) Erasing one or several races
f) Recovering times
14. Regularity rally chronograph (RGRALLy)
a) Setting (SET RLy)
b) Timing a regularity rally - STAGE mode
c) Rereading a regularity rally - STAGE mode
d) Timing a regularity rally - SPLIT mode
e) Rereading a regularity rally - SPLIT mode
f) Erasing regularity rally data
g) Recovering times
15. Countdown (TIMER)
a) Setting (SET TMR)
b) Use
16. Second timezone (TIME 2)
a) Setting (SET T2)
b) SWAP function
c) An example using the SWAP function

1110
3. CHR ADD: chronograph with intermediate/split times and tachymeter – see
chapter 10.
4. LAP TMR: “lap” counter chronograph to calculate lap times – see chapter 11.
5. RALLY: rally chronograph enabling timing of different races that are part of the
same rally. Each race can record intermediate times and penalty times can be
added.
6. RACE: race track lap timer, with the option of recording intermediate lap times.
7.
RGRALLY: regularity rally or TSD (Time-Speed-Distance) rally chronograph.
After defining the target times for the stages or intermediate times, this
chronograph gives the time measured and compares it with the predefined
time stating the lead or the lag.
8. TIMER: countdown – see chapter 15.
9. TIME 2: second timezone, can easily be exchanged with the main TIME zone –
see chapter 16.
10. UTC: reference time of the watch that must correspond to the UTC time – see
chapter 4.
11. NOTIFY: if the watch has been paired with a smartphone, the option exists of
receiving notifications of incoming phone calls, messages and emails on the
watch. In addition, the time of the next meeting taking place during the day
can be displayed – see chapter 17.
1. GENERAL INSTRUCTIONS
This multifunction chronograph, chronometer-certified by the COSC, is equip-
ped with a rechargeable battery. Depending on how it is used, it will need to
be charged every 20 to 50 days.
It also has the option of connecting to a smartphone such as an Apple iPhone®
or Android™. The connection is achieved through Bluetooth®Low Energy
(BLE) or Bluetooth®Smart.
a) Reference time and timezones
IMPORTANT: It must be understood that the reference time for the watch is the
UTC timezone (standing for Coordinated Universal Time), which corresponds
to the former GMT (Greenwich Mean Time) designation. This can be found on
the www.breitling.com website. The local time (TIME) and the second timezone
(TIME 2) are adjusted according to the time difference with the UTC timezone
(in one hour and/or 15-minute increments).
b) Functions
The following functions are available by default:
1. TIME: Main timezone, permanently indicated by the hands, with the option of
displaying the date (DATE) – see chapters 5, 6 and 8.
2. AL 1 to AL 7: seven daily alarms-see chapter 9.

1312
The crown can be turned forwards (clockwise) or backwards (anti-clockwise).
If one forgets the crown in the pulled out position, the upper screen will display
PUSH CROWN at regular intervals, while a beep will sound every 30 seconds.
A short press on the crown will light up the two digital displays. If the TILT
function has been activated (see chapter 7.b), the light will automatically
switch on depending on the position of the wrist.
The watch has two pushpieces (P1 at 2 o’clock and P2 at 4 o’clock), whose action
is connected to the function selected. Depending on the desired action, the user
must give a short or long (about 2 seconds) press. If no action is associated with the
pushpieces, NOP will appear in the upper screen.
WAIT: indicates that the watch is in the process of calculating.
OVF (overflow) indicates that a counter limit has been exceeded.
d) Light intensity setting
A long press on the crown activates the light intensity setting mode. This setting
takes place by turning the crown:
LIGHT will appear in the upper screen, then select
x
/4 – x which represents the level from 1 to 4. The new setting must be confirmed
by a short press of the crown. After 10 seconds, the watch automatically exits the
setting function.
12. SETTING: various settings that make it possible to configure and personalize the
watch – see chapter 7.
13. BAT: Battery charge status indicator – see chapter 18.
The three RALLy , RACE and RGRALLy functions can be masked temporarily if
they are not required (see chapter 7.h).
c) User interfaces
The watch has 3 central hands (hours H, minutes M and seconds SEC) as well as
2 digital displays: upper screen at 12 o’clock (consisting of 7 alphanumeric digits
███████) and lower screen at 6 o’clock (6 digits 88:88:88).
The different functions are selected by turning the crown.
The latter shows two stable axial positions:
– neutral 1 (to change functions)
– pulled out 2 (for settings)
– as well as an unstable position 0
(which acts as a pushpiece,
notably to light up the digital displays).

1514
The higher the figure, the greater the light intensity. Bear in mind that the greater
the light intensity, the more battery is used, which will result in shorter autonomy
(see chapter 2).
e) “Parking” the hands
A double press on the crown allows the hour and minute hands to be “parked” (at
09:14 or 02:46) so as not to affect the readability of the two digital displays. The
seconds hand continues to move forward as usual. In this mode, all digital functions
remain perfectly functional. By default, the hands can only move out of parking
mode after a second double press. There is however an option that allows them to
move forward automatically after 5 minutes (see chapter 7.g).
The hands are automatically “parked” when the crown is pulled out to SETTING
mode.
f) Blocking a function
Should you wish to keep a specific function displayed, this can be done by
deactivating the crown rotating function in neutral position. In order to do this,
push the crown three times. The word
LOCKED will appear in the screen at 12 o’clock
for around 2 seconds. From now on, the selected function will remain displayed
until you push the crown three times again (and
UNLOCKD will appear in the screen
at 12 o’clock). If the crown is turned in “locked” mode, the word
LOCKED will appear
at 12 o’clock for 2 seconds.
g) Connecting the watch to a smartphone
The watch is equipped with a BLE (Bluetooth®Low Energy) antenna enabling
it to be paired with an Apple iPhone®or Android™ type smartphone. Using a
dedicated application on the smartphone, it is possible to adjust all the settings,
including the time as well as recovering certain information from the
CHR ADD ,
the
LAP TMR and the RALLy , RACE and RGRALLy counters. It is also possible, when
connected, to display notifications of phone calls (caller name or number),
messages and emails received on the smartphone; the watch can also indicate
reminders of meetings stored on the smartphone.
If necessary, updating of the watch’s firmware is also possible. The configuration is
described in chapters 7.i and 17.
2. RECHARGEABLE BATTERY AND POWER MANAGEMENT
a) Rechargeable battery
The watch is powered by a rechargeable Li-ion battery. Charging takes place
through two contacts located at 9 o’clock, on the side of the case, by using a spe-
cial cable supplied with the chronograph. The connector consists of an integrated
magnet that ensures the contact with the watch.
N.B.: Please take care not to short-circuit the two contacts on the recharging cable
and in particular, never place the ends of the cable on metallic surfaces.

1716
Graph 2: Typical autonomy in days (connection ON with 20 notifications per day) according to
the use of light in minutes per day (for the four intensity settings).
0
5
10
15
20
25
30
0 2 4 6 8 10 12 14 16 18 20
Daily light use (minutes)
Connexion ON + 20 Notications
Autonomy (days)
intensity 1
intensity 2
intensity 3
intensity 4
Graph 1: Typical autonomy in number of days for 10 minutes use of the light and 10 seconds per
day of alarm (vibrate function and buzzer) with or without a connection and 20 notifications,
according to the light intensity setting.
0
10
20
30
40
50
60
1 2 3 4
Connection OFF
Connection ON
Connection ON + Notications
Typical autonomy in days
Intensity control

1918
correctly indicated, the digital functions are operational and the alarms only
work with the buzzer. This state can last a few days.
3. 3rd level (“soft sleep”): Stop the motors by “parking” the hour and minute
hands (at 09:14 or 02:46); the seconds hand will remain at 12 o’clock, and the
LCD displays will go out. As a consequence, the watch will go into sleep mode
allowing the synchronization of the hands to be maintained, as well as the
correct time and date in background mode. This state can last for about 30 days,
but for any longer than this, the information will be lost and the watch will have
to be reinitialized. The watch must be charged to exit sleep mode.
Once the charge begins, the hands and various indicators (TIME, DATE, etc.) will
be updated. If there is too long a time lapse before recharging the watch, a
complete reset will be required (see chapter 3).
NB: Depending on how the watch is used (high energy-consuming functions), as
well as environmental conditions (ambient temperature), the moment the 1st level
appears, as well as the duration of levels 1 and 2 may vary.
The BATTERy function will display the battery charge at any time.
A battery change will only be required after around 300 complete charges, or after
more than ten years of use. This may only be done by an authorized Breitling ser-
vice center.
The autonomy of the watch depends on how it is used. The main consumers of
energy are the LCD display lighting, the vibration function, followed to a lesser
degree by the audible alarm and the BLE connection. The more these elements
are used, the less autonomy the watch will have. The graphs 1 & 2 provide typical
autonomy values according to light usage.
b) Power management
The watch is equipped with an intelligent power management system serving
to optimize its autonomy. The ultimate aim is to avoid having to re-adjust it
once again after a “stop”. Depending on the status of the battery charge, the
watch will inform the user of the need to charge. Parallel to this it will deactivate
high-consumption functions little by little as the battery is used up. The sequence
includes three successive levels:
1.
1st level: The seconds hand moves forward in 4-second increments every 4
seconds. The analog and digital times are correctly shown, and the digital func-
tions and alarms are operational.
2. 2nd level: The seconds hand is stopped at 12 o’clock, the high-consumption
functions (light, vibrate, «beeps» function and BLE connection) are deactiva-
ted. With each press on the crown, the LOW BAT indicator appears on the upper
screen instead of and in place of the light. If the watch is configured in
DISPOFF
mode (display only with the light – see chapter 7.d), it automatically goes to
DISP ON mode. The analog time (without the seconds) and the digital time are

2120
c) Battery charging
After purchasing, we recommend completely charging the battery prior to
any handling. In order to do this, the watch must be connected to the cable
supplied, following which the cable itself must be connected to the USB power
adaptor also supplied (see figure 1). The connector is equipped with a magnet
guaranteeing the contact and a mechanical alignment system. As soon as the
contact is made, the watch confirms with a beep sound and a luminous flash
on the LCD display. If the hands were stopped, they will adjust to the right time
and the word
CHARGE will appear in the upper screen.
Once the battery is fully charged, the upper screen will display BAT 100% and the
watch will give off a luminous flash. A full recharge takes around 2 hours.
Once the watch is disconnected from the charger cable (UNPLUG appears in the
upper screen), three things may happen:
1. The watch will function as usual and no action is required.
2. The watch was in sleep mode or not completely flat: in principle, nothing needs
to be done, but for safety’s sake, the initialization procedure should be conduc-
ted in order to confirm the different states (see chapter 3).
3. The watch was completely flat and must be initialized (see chapter 3).
Figure 1
3. INITIALIZING THE WATCH
When used for the first time, or after having been charged, the watch guides the
user though the following sequence:

2322
5. Set the main TIME zone (SETTIME) with regard to the difference with the UTC
time (see chapter 6).
6. Press the crown back to neutral position 1.
Depending on the state of the watch prior to being charged, only some, if any,
settings will be required.
N.B.: It is only possible to adjust the minutes in one-minute increments in UTC mode.
In
TIME or TIME 2 mode, the hours are adjusted depending on the difference with
UTC time and the minutes in 15-minute increments. The seconds on the other hand,
can be adjusted precisely in each of the timezones and will automatically be updated
in the other zones.
It is clear that in the event of a change of summer/winter time or the contrary, TIME
and/or TIME 2timezones must be changed, and not the UTC time.
4. ADJUSTING THE TIME BASE OF THE WATCH (UTC)
UTC time is the watch’s main time base. The minute on the time base can only
be adjusted in 1-minute increments in this mode. Any modification to UTC time
will automatically have an effect on TIME and TIME 2(the latter being adjusted
according to the difference with UTC). The display of the UTC time is only available
in 24-hour format.
NOTE: To recharge your watch, please use the cable supplied with the trans-
former.
The cable, can, however be used directly on a USB port on a PC/Mac. In this
event, please note that the short-circuit-proof protection of a USB port on PC/
MAC or on a portable computer differs from one device to another.
In order to avoid any possible issues occurring from faulty electric contacts
during recharging, we recommend cleaning the contacts on the watch before
recharging it. Using a soft cloth to do this (without any special cleaning agent)
is adequate.
Please take care not to short-circuit the two contacts on the recharging cable
and in particular, never place the ends of the cable on metallic surfaces.
1. Pull the crown into position 2 (PULL CROWN) in order to activate the settings
function.
2. Synchronize (SyNCHRO) the hour, minute and seconds hands with the digital
display (see chapter 7.a).
3. Set the exact time on the UTC timezone (SET UTC), which constitutes the watch’s
main time base – and not the local time (see chapter 4).
4. Set the date (SETDATE) (see chapter 5).

2524
• Pull the crown into position 2.
•
Press P2 until the date, SETDATE , appears in the upper screen.
• Select the display mode for the date by turning the crown:
DD/MM (day and then month) or MM/DD (month and day) and confirm by pres-
sing P2. The year flashes (yEAR appears in the upper screen).
• Define the year by turning the crown and confirm by pressing P2. The month
flashes (MONTH appears in the upper screen).
• Define the month by turning the crown and confirm by pressing P2. The day
flashes (DAy appears in the upper screen).
• Define the day by rotating the crown and confirm by pressing P2.
• Select the week display (WEEK NUMBER) by turning the crown and confirm by
pressing P2:
ISO: The first week includes the first Thursday of the year and the first day of the
week is Monday.
ISO-2: The first week includes January 1st and the first day of the week is Monday.
US: The first week includes January 1st and the first day of the week is Sunday.
ARABIC: The first week includes January 1st and the first day of the week is
Saturday.
The setting moves to setting the hour ( SETTIME appears on the upper screen).
a) Setting (SET UTC)
• Select the UTC mode.
• Pull the crown into position 2, SET UTC appears on the upper screen and the time
begins to flash (HOUR appears on the upper screen).
• Turn the crown to adjust the hours and confirm by pressing P2. The minutes will
begin to flash (MINUTE appears in the upper screen).
• Turn the crown to adjust the minutes and confirm by pressing P2. The seconds
will begin to flash (SECOND appears on the upper screen).
• Turn the crown to adjust the seconds and confirm by pressing P2.
• Press the crown back into neutral position 1.
UTC time can be found on www.breitling.com.
N.B.: When in setting mode (SET UTC), pressing P1 will restart the seconds counter
from 0. The seconds counter will only stop when the seconds are changed
manually. In this case, it restarts when exiting setting (putting the crown back
to neutral position 1). The seconds are automatically synchronized with the TIME
and TIME 2zones.
5. SETTING THE DATE (SETDATE)
• Select the TIME mode.

2726
N.B.: When in setting mode (SETTIME), pressing P1 will restart the seconds counter
from 0. The seconds counter only stops when the seconds are manually modified.
In this case, it restarts when exiting setting (putting the crown back to neutral
position 1). The seconds are automatically synchronized on the UTC and TIME 2
timezones.
In TIME mode, pressing P1 makes it possible to go into DATE mode and display the
date according to different formats (see chapter 8). A long press on P1 puts the
display directly back to TIME.
In TIME mode, a long press on P2 allows to choose between either the 12-hour (AM
or PM indicator) or the 24-hour display. The change also happens automatically for
the TIME 2zone and the seven alarms.
7. CONFIGURING THE WATCH (SETTING)
In the SETTING mode, the following adjustments can be made (all these settings are
memorized by the watch and therefore available even in the event of the battery
being completely flat):
1. SyNCHRO: synchronization of the analog display with the digital display.
2. TILT: lighting goes on automatically (and possibly the LCD) depending on the
position of the wrist (positioned around 30° to horizontal), but for a maximum
of 30 seconds, unless in the setting mode (SETTING).
• Press the crown into neutral position 1.
The watch has a perpetual calendar until 2099.
6. SETTING THE MAIN ZONE (TIME)
a) Setting (SETTIME)
• Select the TIME or DATE function.
• Pull the crown into position 2: if the hour was displayed, SETTIME appears on
the upper screen and the setting process (in a loop) starts by the time setting.
If the date was displayed, SETDATE appears on the upper screen and the setting
process will start with adjusting the date. In the second case, press on P2 until
the hours begin to flash (UTC +/-xx).
• By turning the crown, adjust the time in relation to the difference with UTC,
from UTC-12 to UTC+14.
• Confirm by pressing P2; the minutes flash (display MIN +00) on the upper screen.
• If necessary, adjust the minutes in 15-minute increments and confirm by pressing
P2; the seconds flash (SECOND appears on the upper screen).
• Adjust the seconds (which will automatically be adjusted in the TIME 2and UTC)
and confirm by pressing P2.
• Press the crown back to neutral position 1.

2928
a) SyNCHRO
The time shown on the analog display (hands) and that shown on the digital
display (screens) must be perfectly synchronized. In the event of the two displays
being completely out of synchronization (following a shock or accidental stop), the
analog display on the digital indicator is adjusted as follows:
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).
• Select
SyNCHRO by turning the crown.
• Press P1 to activate the setting: the hands will align themselves on the digital
display on the lower screen.
• If there is an inconsistency, turn the crown to position the seconds hand at 12
o’clock and confirm by pressing P2.
• Set the minute hand, and then the hour hand, and confirm by pressing P1.
• Press the crown back to neutral position 1.
b) TILT (ON or OFF)
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).
3. LIGHT: setting the duration for the lighting to be switched on when the crown
is pressed.
4. DISPLAy: choice of digital LCD behavior – readable all the time even without
lighting or readable only with lighting.
5. NIGHT MODE: Option of reducing the light intensity to a minimum and disabling
the TILT mode as well as notifications between 24:00 and 06:00. On the one
hand, this function makes it possible to reduce consumption and on the other,
to avoid the lighting being too bright in the dark.
6. TONE: audible confirmations connected to pushpieces, with or without hourly
time signal or signal for full timekeeping hours.
7. HANDPRK: exit parking the hands mode after 5 minutes or simply with a double
press on the crown.
8. MODE: option of disabling the following functions: RALLy, RACE and RGRALLy.
9. CONNECT: activation and deactivation of the BLE (Bluetooth®Low Energy)
connection.
Please note that as soon as the SETTING mode is activated by pulling the crown into
position 2, the hour and minute hands “park” in order to facilitate the readability
of the two screens.

3130
d) DISPLAy (DISP ON or DISPOFF)
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).
• Select
DISPLAy by turning the crown.
• Press P1 to activate the setting.
• Turn the crown to select DISP ON (always lit) or DISPOFF (only lit with the light).
The default setting is DISP ON.
• Confirm the setting by pressing P1 and/or pressing the crown back into neutral
position 1.
e) NIGHT MODE (ON or OFF)
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).
• Select
NIGHT MODE by turning the crown.
• Press P1 to activate the setting.
• Turn the crown to select ON (activated) or OFF (deactivated). The default setting
is on OFF.
• Confirm the setting by pressing P1 and/or pressing the crown back to neutral
position 1.
• Select
TILT by turning the crown.
• Press P1 to activate the setting.
• Turn the crown to select ON or OFF (the default setting is OFF).
• Confirm the setting by pressing P1 and/or pressing the crown back to neutral
position 1.
N.B.: On the lower screen, a counter indicates the number of tilts activated since
the last battery charge.
c) LIGHT (SHORT, MEDIUM or LONG)
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).
• Select
LIGHT by turning the crown.
• Press P1 to activate the setting and turn the crown to select SHORT (2 seconds),
MEDIUM (4 seconds) or LONG (6 seconds); the default setting is SHORT.
• Confirm the setting by pressing P1 and/or pressing the crown back to neutral
position 1.
N.B.: on the lower screen, a counter indicates the total time the light has been
switched on, in H:MIN:SEC, since the last battery charge.

3332
• Select HANDPRK by turning the crown. The default setting is DBLPRES.
• Press P1 to activate the setting.
• Turn the crown to select 5MIN (exit mode after 5 minutes) or DBLPRES (exit mode
only after a double press on the crown).
• Confirm the setting by pressing P1 and/or pushing the crown back into neutral
position 1.
h) MODE (RACING or SPORT)
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).
• Select
MODE by turning the crown.
• Press P1 to activate the setting.
• Turn the crown to select RACING (all functions) or SPORT (three hidden functions:
RALLy, RACE and RGRALLy). The default setting is on RACING.
• Confirm the setting by pressing P1 and/or pressing the crown back to neutral
position 1.
i) CONNECT (ON or OFF)
• Select the SETTING function by turning the crown.
f) TONE (OFF, PUSH, PUSH+HR or PUSH+CH)
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).
• Select
TONE by turning the crown.
• Press P1 to activate the setting.
• Turn the crown to select:
OFF (no audible confirmation).
PUSH (audible confirmation for every press on the pushpiece).
PUSH+HR (audible confirmation for every press on the pushpiece + time signal on
the count of every hour).
PUSH+CH (audible confirmation for every press on the pushpieces + signal every
full timed hour).
The default setting is on OFF.
• Confirm the setting by pressing P1 and/or pressing the crown back to neutral
position 1.
g) HANDPRK (5 MIN or DBLPRES)
• Select the SETTING function by turning the crown.
• Pull the crown into position 2 (the hour and minute hands will “park”).

3534
3. Week on the upper screen (ex.: WEEK 25) and time on the lower screen (HH:MM:SS)
4. Day, month, year on upper screen (ex.: 28FEB15 for the 28 February 2015) and
time on the lower screen (HH:MM:SS)
5. Back to the standard time display.
A long press on P1 will take you back to the standard time display (TIME).
9. ALARMS (AL1 to AL7)
The watch has seven daily alarms based on local TIME , which can be configured
in hours, minutes and the day of the week.
a) Setting (SET ALx)
• Select the ALx function by turning the crown.
• Select the alarm to be set by pressing P2 (AL1 to AL7)
• Pull the crown into position 2. SET ALx will appear in the upper screen; the hours
(HOUR) flash.
• Adjust the hours by turning the crown and confirm by pressing P2; the minutes
(MINUTE) flash.
• Pull the crown into position 2 (the hour and minute hands will “park”).
• Select
CONNECT by turning the crown. The default setting is on OFF.
• Press P1 to activate the setting.
• Turn the crown to select connection activated (ON) or deactivated (OFF).
• Confirm the setting by pressing P1 and/or pressing the crown back to neutral
position 1.
Leaving the watch constantly connected to the smartphone will reduce its auto-
nomy by approx. ten days.
N.B.: Do not forget to press the crown back once the setting is complete. If
forgotten, the display on the upper screen will indicate PUSH CROWN and a beep
will sound every 30 seconds.
8. DATE DISPLAY (DATE)
In TIME mode, pressing P1 will display the date (DATE mode). Various displays are
possible with successive presses on P1:
1.
Day on the upper screen (ex.: MONDAy , TUESDAy , WED , etc.) and date on the lower
screen (
DD.MM.yy )
2. Week on the upper screen (ex.: WEEK 25) and date on the lower screen (DD.MM.yy)