BRIGHT XLED Series User manual

1
by
Software version 1.4

2
440
790
102
287
Ø200
219
263
Width:
590
XLED Tourpack:
1 x F ightcase
10 x Bright XLED
10 x Hook c amp
10 x Schuko – PowerCon
10 x Safety-wire
Art.no:
XLED basic:
1 x Bright XLED
1 x Hook c amp
1 x Schuko – PowerCon
Art.no: 437613

3
Safety Instructions:
O Do not open this device - there are no user-serviceab e parts inside.
O Do not ook direct y at the ight source when the device is on.
O Caution, this unit's housing may be hot when ights are operating.
O Do not eave any f ammab e materia within 50 cm of this unit whi e
operating or connected to power.
O A ways use a safety cab e when mounting this device overhead.
O Do not operate this device outdoors or in ocation where dust, excessive
heat, water, or humidity may affect it.
O Do not connect this device to a dimmer or other regu ated power
O On y connect this device to a grounded and protected circuit.
O Switchmode powers has high inrush-currents, do not exceed 8A on the
output Powercon when daisy-chaining fixtures (16 units @ 230V)
Main Features:
O High Output 12x8w 4in1 RGBW ed-engine
O F icker free high speed PWM dimming
O Industry standard 5pin XLR and PowerCon
O Inputs and outputs for easy daisy-chaining.
O Inte igent yoke-design enab es direct f oor-mount without remova of
hook c amp.
O Stea th design: A b ack parts, (body, yoke, hook c amp & bo t),
Automatic dimming of LCD back ight.
O Compact size, ow weight and power consumption

4
Display Navigation
When XLED is a ready in DMX-mode, the DMX start
address is disp ayed on the eft side (Axxx), whi e the DMX
channe count is disp ayed on the right side (Cxx).
Use the Up/Down buttons to a ter the DMX start address, and press
Enter/Confirm to set the address permanent y.
If the XLED is not in DMX-mode, or to change other
settings than the start address, press the Menu button to
access the main menu:
Navigate the main menu with the Up/Down buttons, and
use the Enter/Confirm button to se ect a menu item. The XLED wi return to
its previous state if no new setting or mode has been confirmed within 10
seconds.
DMX start A ress
Use Up/Down to a ter the DMX start Address (001→512),
then press Enter/Confirm to set the chosen start address
permanent y.
OSetting the DMX start A ress will activate “DMX Mo e”
DMX Channel count
Use Up/Down to a ter the DMX channe count (3ch, 4ch,
6ch, 9ch), then press Enter/Confirm to set the chosen
Channe count permanent y.
OSetting the DMX Channel count will activate “DMX Mo e”
Menu/Exit
Up Down
Enter/Confirm

5
Static Color
Use Up/Down to step thru any so id combination of R, G,
B and W, then press Enter/Confirm to set Static Co or
permanent y.
OSetting a static color will activate “Color Set” Mo e
Manual Color
Use Up/Down and Confirm/Enter to sequentia y adjust
va ues for RGBW, (000→255), overa Intensity
(000→100) and Strobe speed (S000→S100), then press
Enter/confirm to set Manua Co or permanent y.
OSetting a manual color will activate “Color Set” Mo e
Manual White
Use Up/Down and Confirm/Enter to adjust the co or-
temperature (W1→W11), then set intensity va ue
(D100→000), then press Enter/confirm to set Manua
White permanent y.
OSetting a manual white will activate “Color Set” Mo e
Automatic Programs
Use Up/Down to se ect the bui t-in program
(Pr01→Pr06), press Enter/Confirm, then use Up/Down to
se ect the operating speed of the program
(Sp000→Sp100) and press Enter/Confirm to start Auto
Program at given speed
OSetting a program an spee will activate “Auto MODE”
Soun trig
Use Up/Down to adjust the sensitivity (Sen000→Sen100)
of the in-bui d microphone, then press Enter/confirm to
set Sound sensitivity. permanent y
OSetting the Soun sensitivity will activate “SOUND” Mo e

6
Master/Slave Operation
Use Up/Down to choose Master or S ave mode (M/S), and
press Enter/Confirm.
When using any of the standa one operating modes: auto,
sound, static or manua co or with Master enab ed, the
Master fixture wi transmit and remote contro any
fixtures set to S ave Mode.
OSetting Master/Slave to Slave will activate “Slave MODE”
Factory Reset
Use Up/Down to se ect <Y> for yes, then press
Enter/confirm to reset the fixture to factory defau t
settings.
OResetting the fixture will activate “DMX Mo e”

7
Functions in etails
DMX channels:
The XLED may be set to use 3, 4, 6 or 9 DMX channe s.
The channe order is the same for a modes:
(P ease refer to the DMX Charts for detai ed description)
Inbuilt Automatic Programs:
Pr01: RGBW hard chase Sp000: Stop
Pr02: 15 Co ors hard chase Sp001: S ow
Pr03: RGBW soft chase ↓
Pr04: 15 Co . soft chase Sp100: Fast
Pr05: Random co orfades
Pr06: Specia chaser mode
Special Chaser Mo e (program Pr06)
This mode enab es cascading de ay being app ied to connected s ave units, to
create “running ights” chaser effects without a Lighting conso e (up to 255
groups.)
Settings for the master XLED
1. Set the DMX address to tota number of groups (e.g. 003)
2. Set Auto Program to Pr06 (master is a ways part of group 1)
Settings for the slave XLED’s
1. Set the DMX address to the desired s ave group (e.g. 001, 002 or 003),
2 Set the fixtures to S ave mode,
1 2 3 4 5 6 7 8 9
R G B W Dim Strobe Co or Auto Speed

8
Photometrics
R G B W RGBW
1m
3957 3900 4690 6000 15740
2m
977 1092 1200 1700 4310
3m
430 485 558 747 1911
4m
245 280 308 428 1056
5m
160 185 205 282 693
Beam
Ang e
22º
Fie d Ang e: 35º
Center Lux

9

10
DMX Chart – 3, 4, 6 & 9 Channels mo e
CHANNEL VALUE FUNCTION
1 000-255 Red dimmer: 0% → 100%
2 000-255 Green dimmer: 0% → 100%
3 000-255 B ue dimmer: 0% → 100%
4 000-255 White dimmer: 0% → 100%
5 000-255 Master dimmer 0% → 100%
6 000-009
No function
010-255 Strobe S ow → Fast (1-30Hz)
7
000-019 No Function
020-039 Red 100% / Green 0% → 100% / B ue 0%
040-059 Red 100% → 0% / Green 100% / B ue 0%
060-079 Red 0% / Green 100% / B ue 0% → 100%
080-099 Red 0% / Green 100% → 0% / B ue 100%
100-119 Red 0% → 100% / Green 0% / B ue 100%
120-139 Red 100% / Green 0% / B ue 100% → 0%
140-159 Red 100% / Green 0% →100% / B ue 0% → 100%
160-179 Red 100%→ 0% / Green 100% → 0% / B ue 100%
180-200 Red 100% / Green 100% / B ue 100% / White 100%
201-255 Co or Temperature Warm → Coo
8
000-009 No Function
010-049 Auto Program 1, R G B W hard chase
050-090 Auto Program 2, 15 co ors hard chase
091-131 Auto Program 3, R G B W soft chase
132-172 Auto Program 4, 15 co ors soft chase
173-213 Auto Program 5, Random co ors fading
214-255 Auto Program Sound, Random co ors audio trig
9 000-255 Speed of Auto Programs (S ow → Fast)