Brinkmann 5 Burner Gas Grill with Smoker User manual

8 M6 X 10 mm Bolts
8 Star Washers
 1  AA/1.5VAlkalineBattery
Star Washers
AA/1.5VAlkalineBattery
Qty.
M6 X 10 mm Bolts
20
ASSEMBLY INSTRUCTIONS:
Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before
you begin the installation process.
PARTS BAG CONTAINS:

21
READALLSAFETYWARNINGS&ASSEMBLYINSTRUCTIONSCAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
This grill is designed with Dual Fuel Valves to easily
convert from LP (propane) gas to natural gas.
A Brinkmann conversion kit must be purchased
and installed for use with natural gas.
To see trouble shooting or assembly videos, visit us at:
WERECOMMENDTWOPEOPLEWORKTOGETHERWHENASSEMBLINGTHISUNIT.
The following tools are required to assemble this Brinkmann®5 Burner Gas Grill with Smoker:
• PhillipsScrewdriver
1 Grease Tray
5 Heat Distribution Plates
2 Smoker Cooking Grills
1 Grill Body Assembly
1 Water Pan
1 Water Pan Support
1 Wood Chip Pan Lid
1 Wood Chip Pan
1 Smoker Grease Tray
2 Heat Shield Brackets
1 Heat Shield
PARTS LIST:
1 Left Side Table
6 Support Racks
1 Side Burner Grate
1 Side Burner Assembly
1 Left Side Table Front Panel
1 Warming Rack
1 Side Burner Front Panel
1 Grease Cup
3 Cooking Grills
1 Side Burner Knob
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
9
18
10
19
20
21

100
200
300 500
600
700
38
94
150
206
262
318
374
800
430
400
1
5
3
2
4
8
7
11
16
13
14
19
6
9
12
10
15
18
20
17 21
22
(Proof of purchase will be required.)
Inspect contents of the box to ensure all parts are included and undamaged.
FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT:

Step 1
Attach left side table front panel
to left side table using three
M6 x 10 mm bolts and star
washers. Tighten bolts securely.
Step 2
Attach left side table to left side
of grill body assembly. Place left
side table keyholes over the pre-
attached bolts and slide back.
Tighten securely. Fasten left side
table front panel to grill body with
one M6 x 10 mm bolt and star
washer.
Step 3
Attach side burner front panel to
side burner assembly using three
M6 x 10 mm bolts and star
washers. Tighten bolts securely.
Step 4
Attach side burner assembly to right
side of grill body assembly. Place
side burner assembly keyholes over
the pre-attached bolts and slide
back. Tighten securely. Fasten right
side table front panel to grill body
with one M6 x 10 mm bolt and star
washer.
23

24
Step5
Insert the pre-attached screws in
the side burner valve assembly
through the holes in the side burner
front panel, then rmly seat the
valve nozzle into the burner venturi.
Slide the burner valve assembly
down in the keyholes on the side
burner control knob bezel as
shown to lock in place. Tighten with
screwdriver.
WARNING: Never use your grill
without leak testing all
gas connections and
hoses. See the section
on“LeakTesting”in
this manual for proper
procedures.
Step6
Install side burner control knob onto
valve stem.
Step7
Attach side burner igniter lead wire
to the electrode as illustrated.
Side Burner
Control Knob
Bezel
Side Burner
Igniter Lead Electrode
Side
Burner
Valve
Burner Venturi
Valve
Nozzle

25
Step 8
Place the side burner grate onto
the side burner table.
Step9
Insert the support racks into the
holes on the inside walls of the
smoker.
Step 10
Attach heat shield with brackets
to water pan support. Then slide
water pan support into the lowest
rack.
Support Racks
Water Pan
Support
Heat Shield
Support
Rack

26
Step 11
Place the wood chip pan and wood
chip lid onto the center of the heat
shield.
Step 12
Place water pan onto water pan
support.
Step 13
Slide the smoker cooking grills onto
support racks.
Step 14
Slide the smoker grease tray into
the smoker chamber under the
burner.
Step15
Insert grease tray in back of grill,
then hang grease cup on brackets
under the grease tray.
Grease Tray
Grease Cup
Heat Shield
Wood Chip
Pan
Wood Chip
Pan Lid
Water
Pan
Water Pan
Support
Smoker
Cooking
Grills
Smoker
Grease
Tray
Smoker
Burner
Support
Rack

27
Step 14
Place the heat distribution plates
on lower level of grill body
assembly directly above burners.
Step15
Place cooking grills on support
ribs directly above heat distribution
plates
Step16
Insert warming rack onto brackets
so that it sits above the cooking
grills.
Step17
Remove igniter cap and insert
battery with position end of battery
toward igniter cap. Ensure spring is
in place inside igniter cap. Replace
igniter cap and make sure the
igniter is working properly.
100
200
300 500
600
700
38
94
150
206
262
318
374
800
430
400
Cooking Grills
Heat
Distribution
Plates
Brackets
Igniter Cap
Battery
Warming Rack

100
200
300 500
600
700
38
94
150
206
262
318
374
800
430
400
Brinkmann®5 Burner Gas Grill & Smoker (Assembled)
28