Briteq BT-PROFILE HD User manual

Other languages can be downloaded from:
WWW.BRITEQ-LIGHTING.COM
ENGLISH
Operation Manual
Version: 1.0
JB LOGO MET
JUISTE SPACING
(enkel voor JBS !!!)
FOTO / TEKENING
TOEVOEGEN

ENGLISH OPERATION MANUAL
BRITEQ®1/9 BT-PROFILE HD
OPERATION MANUAL
Thank you for buying this Briteq®product. To take full advantage of all possibilities and for your own safety,
please read these operating instructions very carefully before you start using this unit.
FEATURES
•A very compact but powerful “ALL-IN-1” full color LED profile with:
•Integrated manual 25° ~ 50° zoom.
•4 blade shutter framing system to make sharp beam cuts.
•No more need for separate white and color projectors, BT-PROFILE HD does it all:
•Perfect WHITE with high CRI > 90Ra and CCT presets
•Rich COLOR selection with color presets!
•Thanks to the CCS Color Calibration System the color differences between different batches is a problem
of the past, while this profile also works perfectly together with our existing BT-THEATRE HD2:
•The same CCT presets for white, ranging from 1800K to 10000K !
•The same 48 calibrated color presets (according to LEE® / ROSCO® numbering)
•Based on a 150watt 5-color RGBAL LED-cluster (Red, Green, Blue, Amber, Lime)
•Very silent operation with low noise cooling fan and different presets (live, studio, …)
•DMX-controlled: 6 different channel modes for maximum flexibility
•RDM-functionality for easy remote setup: DMX addressing, channel mode, …
•Flicker free TV-recordings thanks to the adjustable high LED-refresh rate!
•Four dimmer settings with different behavior & speed.
•Manual control for dimming, colors, CCT & zoom.
•OLED-display to navigate easily through the setup menu!
•In case of DMX failure, you can choose between blackout and freeze mode.
•Lock function to avoid unwanted altering of the settings.
•Lightweight but rugged housing.
•5pin DMX in/outputs + PowerCON TRUE1 in/outputs for easy daisy chaining.
BEFORE USE
•Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
•Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for
the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by
mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or
problems caused by disregarding this user manual.
•Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.
Check the contents:
Check that the carton contains the following items:
•BT-PROFILE HD
•Power cable
•Safety cable
•English operating instructions, other languages can be downloaded from our website.

ENGLISH OPERATION MANUAL
BRITEQ®2/9 BT-PROFILE HD
SAFETY INSTRUCTIONS:
•To protect the environment, please try to recycle the packing material as much as possible.
•To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
•To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
•This unit is for indoor use only.
•Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
•Locate the fixture in a well-ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
•Don’t cover any ventilation openings as this may result in overheating.
•Prevent use in dusty environments and clean the unit regularly.
•Keep the unit away from children.
•Inexperienced persons should not operate this device.
•Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
•Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and
servicing.
•Allow the device about 10 minutes to cool down before to start servicing.
•Always unplug the unit when it is not used for a longer time or before to start servicing.
•The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
•Check that the available voltage is not higher than the one stated on the unit.
•The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
•Never let the power-cord come into contact with other cables!
•This fixture must be earthed in order to comply with safety regulations.
•Don’t connect the unit to any dimmer pack.
•Always use an appropriate and certified safety cable when installing the unit.
•In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user
serviceable parts inside.
•Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same type
and electrical specifications!
•In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
•The housing and the lenses must be replaced if they are visibly damaged.
•Please use the original packing when the device is to be transported.
•Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
CAUTION: To reduce the risk of electric shock, do not remove
the top cover. No user-serviceable parts inside. Refer servicing
to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 1 meters
CAUTION: Do not stare at operating lamp.
May be harmful to the eyes.

ENGLISH OPERATION MANUAL
BRITEQ®3/9 BT-PROFILE HD
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper installation
can result in serious injuries and/or damage to property. Overhead rigging requires extensive
experience! Working load limits should be respected, certified installation materials should be used,
the installed device should be inspected regularly for safety.
•Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
•Locate the fixture in a well-ventilated spot, far away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
•The device should be installed out of reach of people and
outside areas where persons may walk by or be seated.
•Before rigging make sure that the installation area can
hold a minimum point load of 10times the device’s weight.
•Always use a certified safety cable that can hold 12times
the weight of the device when installing the unit. This
secondary safety attachment should be installed in a way
that no part of the installation can drop more than 20cm if
the main attachment fails.
•The device should be well fixed; a free-swinging mounting
is dangerous and may not be considered!
•Don’t cover any ventilation openings as this may result in
overheating.
•The operator has to make sure that the safety-relating and
machine-technical installations are approved by an expert
before using them for the first time. The installations
should be inspected every year by a skilled person to be
sure that safety is still optimal.

ENGLISH OPERATION MANUAL
BRITEQ®4/9 BT-PROFILE HD
SETUP MENU / HOW TO SETUP
With the setup menu you can fully configure the projector. All settings are preserved when the unit is
disconnected from the mains.
■[MENU] button: press to enter / leave the setup menu.
►[ENTER] button: press to select / confirm or store the current menu option or value.
▲/▼ [UP/DOWN] button: press to navigate the setup menu or change a value.
STATIC
RED
0-255
Combine [RED] [GREEN] [BLUE]
[LIME] [AMBER] [CYAN] to create
an infinite range of colors (0-255).
Set the value of the [STROBE] (0-
25Hz).
GREEN
0-255
BLUE
0-255
AMBER
0-255
LIME
0-255
STROBE
0-25
ADDRESS
001-512 (default 001)
Set the DMX ADDRESS
RUN MODE
DMX (default)
[DMX] Using the DMX 512 controller
to control.
[SLAVE] for Master/Slave operation.
SLAVE
PERSONALITY
BASIC
Use the menu to select desired
channel mode
SSP
TOUR (default)
TR16
HSIC
CMY
AUTO
PROGRAM
AUTO 1
0-255
Selects automatic AUTO program
and AUTO program speed.
Programs [CUSTOM 1] to [CUSTOM
2] are fully pre-programmed and can
be edited in [EDIT] mode.
AUTO 2
0-255
...
0-255
AUTO 10
0-255
PR 1
PR 2
EDIT
PROGRAM
1-2
SCENE
01-10
RED
0-255
Enter the [EDIT] mode to edit the
custom programs [PROGRAM01] to
[PROGRAM2].
Each custom program has 30
scenes that can be edited.
Fade transition time: time 0-255 unit
in seconds, fade time setting should
be less than time setting.
After editing the program, Play in
AUTO.
GREEN
0-255
BLUE
0-255
AMBER
0-255
LIME
0-255
STROBE
0-25
TIME
0-255
FADE
0-255
UPLOAD
****
SEND
Select [UPLOAD] to upload the
custom programs
SETTING
****
RESET
****
RESET
Restore factory settings
DIMMER
DIM4 (default)
Dimming speed DIM1 (fast) to DIM4
(slow) ；
OFF
DMX
SAVE (default)
Hold after loss of DMX signal
ERROR
BLACK
Blackout after loss of DMX signal
LED PWM
1200Hz (default)
Sets the PWM frequency
2400Hz
4000Hz
6000Hz
25000Hz
PERFORM
LIVE (default)
Fan mode low speed
POWER
Fast rotation of fan ， all power
STUDIO
Automatic rotation of fan
DISP KEY
ON (default)
Locks display (passcode is <UP>,
<DOWN >,<UP>, <DOWN>,
<ENTER>)
OFF

ENGLISH OPERATION MANUAL
BRITEQ®5/9 BT-PROFILE HD
DISP
TIME
ON
Display backlight always on
10s
Turns off display backlight after 10s /
30s
/ 2min of inactivity
30s (default)
2min
FIXTURE HOURS
Hours of fixture use
VERSION
Software versions
INFO
RDM
UID
0x21220xxxxxxx
Check fixture's ID
LABEL
BT-PROFILE HD
Check fixture's LABEL
CCT
1800K
Preset color temperatures
2200K
2700K
3000K
3200K
4000K
4500K
5000K
5600K
6000K
6500K
7000K
8000K
10000K
PRESET
COLOR
COLOR 1
Preset color
(See Annex I for details)
COLOR 2
...
COLOR 48
All passwords of this product are <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>)
ELECTRICAL INSTALLATION
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Electrical installation for two or more units in DMX-mode:
•The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units.
•Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
•To prevent strange behavior of the light effects, due to interferences, you must use a
90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this simply
won’t work!
•Make sure that all units are connected to the mains.
•Each unit in the chain needs to have its proper starting address so it knows which
commands from the controller it has to decode.
RDM FUNCTIONS / REMOTE SETUP
RDM means “Remote Device Management”. This projector works with a brief set of RDM-functions which
means that it can setup a bi-directional communication with an RDM-compatible DMX-controller. Some of
these functions are briefly explained below, others will be added in the future.
•The DMX-controller sends out a “discovery command”, all RDM devices respond and send their unique
device ID.
•The DMX-controller asks each RDM device for some basic data so it knows which devices are connected.
The projector will respond:
•Device name: BT-PROFILE HD
•Manufacturer: Briteq®
•Category: LED Dimmer
•Firmware: x.x.x.x (firmware version of the projector)

ENGLISH OPERATION MANUAL
BRITEQ®6/9 BT-PROFILE HD
•DMX address: xxx (current DMX start address of the projector)
•DMX footprint: xx (number of DMX-channels used by the projector)
•Personality: xx (current personality [or DMX-working mode] used by the projectors)
•The DMX-controller can send certain commands to each RDM device which allow remote setup of the units.
Thanks to this the projector can be setup remotely.
The following functions can be managed remotely:
No more need to take a ladder and set all units one by one!
•DMX START ADDRESS: The start address can be set remotely from 001 to xxx.
•PERSONALITY: The DMX working mode (DMX-chart) can be set remotely.
These 2 functions make it possible to prepare a complete DMX-patch of all projectors on the DMX-controller
and send these data to all projectors at once. More functions will be added later.
DMX CHARTS
Personalities: Basic (3CH) + SSP (7CH) + HSIC (8 CH) + CMY (10CH) + TOUR (12CH) + TR16 (18CH)
BASIC
(3CH)
SSP
(7CH)
TOUR
(12CH)
TR16
(18CH)
HSIC
(7CH)
CMY
(10CH)
Function
Values
1
1
1
1
1
1
Dimmer
0-255
Intensity 0 to 100%
--
--
--
2
--
--
Dimmer fine
0-255
Dimmer intensity fine
--
2
2
3
--
--
Red
0-255
0 to 100%
--
--
--
4
--
--
Red fine
0-255
Red fine
--
3
3
5
--
--
Green
0-255
0 to 100%
--
--
--
6
--
--
Green fine
0-255
Green fine
--
4
4
7
--
--
Blue
0-255
0 to 100%
--
--
--
8
--
--
Blue fine
0-255
Blue fine
--
5
5
9
--
--
Amber
0-255
0 to 100%
--
--
--
10
--
--
Amber fine
0-255
Amber fine
--
6
6
11
--
--
Lime
0-255
0 to 100%
--
--
--
12
--
--
Lime fine
0-255
Lime fine
--
--
--
--
2
--
Hue
0-255
Hue 0 to 360°
--
--
--
--
3
--
Hue fine
0-255
Hue fine
--
--
--
--
4
--
Saturation
0-255
Saturation 0 to 100%
--
--
--
--
--
2
Cyan
0-255
0 to 100%
--
--
--
--
--
3
Magenta
0-255
0 to 100%
--
--
--
--
--
4
Yellow
0-255
0 to 100%
2
--
7
13
--
5
Color presets
0-010
Disabled
011-255
Preset colors (annex 1 for details)
3
--
8
14
5
6
Linear CCT
0-9
Disabled
010
1800K
025
2200K
040
2700K
055
3000K
070
3200K
085
4000K
100
4500K
115
5000K
130
5600K
145
6000K
160
6500K
175
7000K
190
8000K
205
10000K
255
10000K
--
--
9
15
--
7
Auto programs
0-040
Disabled
41-50
AUTO 1

ENGLISH OPERATION MANUAL
BRITEQ®7/9 BT-PROFILE HD
51-60
AUTO 2
61-70
AUTO 3
71-80
AUTO 4
81-90
AUTO 5
91-100
AUTO 6
101-110
AUTO 7
111-120
AUTO 8
121-130
AUTO 9
131-140
AUTO 10
141-150
PROGRAM 1
151-160
PROGRAM 2
161-255
No function
--
--
10
16
8
Auto speed
0-255
Slow to fast
--
7
11
17
6
9
Shutter
000-009
Open
010-099
Strobe (0-25Hz)
100-109
Open
110-179
THUNDER STROBE
180-189
Open
190-255
Random Strobe
--
--
12
18
7
10
Control
000-060
No function
061-070
Fan mode = Live *
071-080
Fan mode = Studio *
081-090
Fan mode = Power *
091-100
Reserved
101-110
Dimmer speed off *
111-120
Dimmer speed Dim4 *
121-150
Reserved
151-160
PWM = 1200Hz *
161-170
PWM = 2400Hz *
171-180
PWM = 4000Hz *
181-190
PWM = 6000Hz *
191-200
PWM = 25000Hz *
201-210
All reset *
211-255
Reserved
*Function will be activated after 3s
MAINTENANCE
•Make sure the area below the installation place is free from unwanted persons during servicing.
•Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
•All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
•Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
•When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
•The mains cables must be in impeccable condition and should be replaced immediately when even a small
problem is detected.
•In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
•The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
•The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize
light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
•Clean with a soft cloth using normal glass cleaning products.
•Always dry the parts carefully.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!

ENGLISH OPERATION MANUAL
BRITEQ®8/9 BT-PROFILE HD
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
Mains Input: AC 100 - 240V, 50/60Hz
Fuse: T3.15A / 250V (20x5mm)
Power consumption (max): 170 Watts
Power connections: Lockable IP Power connector, input / output
Power Linking capacity: 6A @ 240V
DMX connections: 5 pin-XLR male / female inputs + outputs
Lamp: RGBAL LED 170W
CRI:>90
Beam Angle: manual zoom 25° ~ 50°
IP-Rating: IP20
Operating Temperature: 0°C –45°C
Size: See drawing
Weight: 6,2 kg
DIMENSIONS:
LUX CHARTS

ENGLISH OPERATION MANUAL
BRITEQ®9/9 BT-PROFILE HD
ANNEX 1 ➔COLOR PRESETS + LEE / ROSCO FILTER NAMES + CIE 1931 X/Y coordinates
PRESET
COLOR
VALUE
COLOR NAME
X
Y
000-010
NO FUNCTION
COLOR 1
011-015
L176
Loving Amber
0.407
0.321
COLOR 2
016-020
R40
Light Salmon
0.499
0.321
COLOR 3
021-025
L24
Scarlet
0.561
0.296
COLOR 4
026-030
L164
Flame Red
0.659
0.302
COLOR 5
031-035
L747
Easy White
0.389
0.344
COLOR 6
036-040
R303
Warm Peach
0.448
0.353
COLOR 7
041-045
L08
Dark Salmon
0.498
0.347
COLOR 8
046-050
L25
Sunset Red
0.566
0.359
COLOR 9
051-055
L04
Medium Bastard Amber
0.37
0.335
COLOR 10
056-060
L237
C.I.D. (To Tungsten)
0.43
0.365
COLOR 11
061-065
R321
Soft Golden Amber
0.477
0.406
COLOR 12
066-070
L652
Urban Sodium
0.535
0.399
COLOR 13
071-075
L212
L.C.T. Yellow (Y1)
0.34
0.363
COLOR 14
076-080
L765
LEE Yellow
0.389
0.412
COLOR 15
081-085
L513
Ice and a Slice
0.38
0.447
COLOR 16
086-090
L100
Spring Yellow
0.41
0.502
COLOR 17
091-095
L244
LEE Plus Green
0.324
0.388
COLOR 18
096-100
R4430
Cal Color 30 Green
0.318
0.44
COLOR 19
101-105
L122
Fern Green
0.234
0.543
COLOR 20
106-110
L90
Dark Yellow Green
0.184
0.641
COLOR 21
111-115
L243
LEE Fluorescent 3600K
0.286
0.37
COLOR 22
116-120
R92
Turquoise
0.235
0.36
COLOR 23
121-125
R94
Kelly Green
0.185
0.459
COLOR 24
126-130
L327
Forest Green
0.162
0.496
COLOR 25
131-135
L191
Cosmetic Aqua Blue
0.3
0.318
COLOR 26
136-140
L728
Steel Green
0.256
0.302
COLOR 27
141-145
L117
Steel Blue
0.223
0.278
COLOR 28
146-150
L354
Special Steel Blue
0.173
0.265
COLOR 29
151-155
L53
Paler Lavender
0.284
0.284
COLOR 30
156-160
L501
New Color Blue
0.246
0.249
COLOR 31
161-165
L174
Dark Steel Blue
0.204
0.205
COLOR 32
166-170
L165
Daylight Blue
0.159
0.158
COLOR 33
171-175
L136
Pale Lavender
0.288
0.254
COLOR 34
176-180
L194
Surprise Pink
0.24
0.183
COLOR 35
181-185
L142
Pale Violet
0.209
0.148
COLOR 36
186-190
L700
Perfect Lavender
0.177
0.07
COLOR 37
191-195
L35
Light Pink
0.335
0.289
COLOR 38
196-200
L794
Pretty 'n Pink
0.335
0.251
COLOR 39
201-205
L328
Follies Pink
0.335
0.18
COLOR 40
206-210
L795
Magical Magenta
0.327
0.138
COLOR 41
211-215
L154
Pale Rose
0.35
0.318
COLOR 42
216-220
L127
Smokey Pink
0.397
0.265
COLOR 43
221-225
L192
Flesh Pink
0.41
0.237
COLOR 44
226-230
L332
Special Rose Pink
0.465
0.193
COLOR 45
231-235
L790
Moroccan Pink
0.378
0.324
COLOR 46
236-240
L157
Pink
0.457
0.272
COLOR 47
241-245
R332
Cherry Rose
0.489
0.295
COLOR 48
246-250
L128
Cool LED Bright Pink
0.57
0.263
251-255
NO FUNCTION
The information might be modified without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com