Brookstone Airphones User manual

WIRELESS NOISE-CANCELLING HEADPHONES

IN THE BOX
3.5mm Audio Cable
USB Type-C Cable
Airplane Adapter
User Guide
Carrying CaseWireless Headphones
WIRELESS NOISE-CANCELLING HEADPHONES
01

LOCATION OF CONTROLS
Multifunction
Touchpad
3.5mm Audio
Jack
RIGHT SIDE
Microphone
Right LED Indicator
(Status of ANC modes and
Bluetooth connected state)
USB Type-C
Port
Left LED Indicator
(Charging status)
Active Noise
Cancellation
Modes
Power Button
Bluetooth Pairing
Mode ON/OFF
LR
02

The headphones include two LED
indicators, the Right LED indicator and
the Left LED indicator.
Both LED indicators are explained below.
LED INDICATORS
Left LED Indicator
Charging
Fully Charged
Solid RED
Solid GREEN
Charging
Pairing Mode
Connected
Not Connected
Flashes RED and BLUE
Slowly flashes BLUE (every 5 seconds)
Quickly flashes BLUE (every second)
Bluetooth
Noise Cancelling
Ambient Sound
Ambient Sound and
Noise Cancelling Off
Solid GREEN
Solid WHITE
Off
ANC
Low Battery Flashes RED twice every 5 seconds
Battery
Right LED Indicator
Right LED
Indicator
Left LED
Indicator
03

CHARGING
Insert the USB Type-C cable into the USB port of the headphones as shown below
and connect the other end to any USB Charger or charging device. The Left LED
indicator will turn solid RED while charging and become solid GREEN when fully
charged.
While charging, the headphones cannot be powered on or used.
Note: When the battery is low, the Right LED indicator flashes red twice every
5 seconds and the “battery low” voice prompt will be heard.
Wall outlet
USB Charger
(not included)
USB Type-C Cable
USB Type-C Port
L R
04

POWER ON/OFF
Power ON:
Press and HOLD the Power button until the Right LED indicator lights BLUE.
Power OFF:
Press and HOLD the Power button until the Right LED indicator turns off.
Note: If not connected to a Bluetooth enabled device, the headphones will
automatically power off after 5 minutes.
Power Button
Right LED
Indicator R
05

Power on the device and follow the steps
below to pair your Bluetooth- enabled
device.
1. Press and HOLD the Bluetooth button
until Right LED flashes red and blue,
the voice prompt“Bluetooth pairing on”
will be heard.
To exit Bluetooth pairing mode, press
and quickly release the Bluetooth button.
2. Open your device’s Bluetooth menu.
3. Find and select BKH928 to pair.
4. Once paired, the voice prompt “Connected” will be heard and the Right LED
indicator will flash BLUE every five seconds.
Bluetooth Profiles: A2DP V1.3, AVRCP V1.6, HFP V1.7, HSP V1.2
BLUETOOTH PAIRING
Bluetooth menu
on your device Wireless Headphones
BKH928
DEVICES
Bluetooth
i
Right LED
Indicator
06

Disconnecting
To disconnect from a device, press and HOLD the Bluetooth Pairing Button
until the Right LED indicator flashes RED and BLUE, the voice prompt “Bluetooth
pairing on” will be heard. You can now pair the headphones to another device.
Note: This feature is handy to quickly pair the headphones to another Bluetooth
enabled device.
Right LED
Indicator
Bluetooth
Pairing Button
L R
07

The ANC modes offer 3 different listening
experiences. Press the ANC button to cycle
through the different modes below.
1. Noise Cancelling (NC) Mode: LED
This mode isolates your listening
experience specifically to sound coming
through the headphones and helps
blocking unwanted outside noise.
NC mode is automatically activated
by default when the headphones are
powered on. When NC mode is active, the
Right LED indicator of the headphones
turns solid GREEN.
2. Ambient Sound Mode: LED
Ambient mode allows you to listen to
the sounds around you through the
built-in microphones even while wearing
the headphones.
To enter Ambient mode, press the ANC button once and the voice prompt
“Ambient sound” is heard, the Right LED indicator of the headphones will
turn solid WHITE.
Note: Ambient mode allows you to hear background noise clearer, such as
important announcements and street traffic. However, certain sounds may
not be heard well depending on the environment. Be cautious in places where
an inability to hear ambient sound would be dangerous.
3. Ambient Sound and NC OFF: LED OFF
Press the ANC button twice and the voice prompt “Ambient sound and noise
cancelling off” is heard, the Right LED indicator will turn off.
To turn NC mode back on, press the ANC button again.
ANC ACTIVE NOISE CANCELLATION MODES
ANC Button
Right LED
Indicator
R
08

The headphones include a multifunction touchpad located over the right earcup.
Use the following gestures to control audio playback and answer calls.
Play/Pause: Double tap quickly
Next Track: Triple tap quickly (four taps to go back)
TOUCH CONTROL (TOUCHPAD OPERATION)
Tap the center of
the touchpad
Multifunction
Touchpad
R
09

Manual Volume Control:
To manually increase or decrease the volume, place your finger at either the top
or bottom of the earcup as shown, and slowly swipe across to the other end.
Slowly swipe down from
the top edge to the bottom
Slowly swipe up from
the bottom edge to the top
R
10

Automatic Volume Control:
To automatically increase or decrease the volume, place your finger at either the
top or bottom of the earcup as shown, and slowly swipe and HOLD your finger at
the center of the earcup.
The volume will either increase or decrease (depending on where you swiped
from) until you release your finger from the earcup.
Slowly swipe down from the top edge to the center,
and HOLD your finger at the center of the earcup
until the desired volume level is reached
Slowly swipe up from the bottom edge to the
center, and HOLD your finger at the center of the
earcup until the desired volume level is reached
R
11

Answer a Call:
Double tap quickly during an incoming call.
Rejecting a Call:
Touch and HOLD during an incoming call.
Voice Assistant:
Touch and HOLD until the default voice
assistant of your device is activated. You
can touch and HOLD again to cancel.
(This may not be supported on all devices.)
Touch and HOLD
Double tap
R
12

Monitor:
Place the palm of your hand over the right earcup, the music is muted until
you release your palm from the earcup.
Multifunction
Touchpad
R
13

When connecting the 3.5mm audio cable, the headphones will power off and
play audio directly from the connected device.
USING THE AUDIO CABLE
3.5mm Audio Cable
Device
Wireless Headphones
3.5mm Audio
Jack
R
14