Brother HL-1470N Installation instructions

i
M
Mu ul lt ti i- -P Pr ro ot to oc co ol l P Pr ri in nt t S Se er rv ve er r
N
Ne et tw wo or rk k U Us se er r’ ’s s G Gu ui id de e
Please read this manual thoroughly before using the printer. You can print or view this
manual from the CD-ROM at any time, please keep the CD-ROM in a convenient place for
quick and easy reference at all times.
The Brother Solutions Center (http://solutions.brother.com) is your one stop resource
for all your printer needs. Download the latest drivers and utilities for your printers, read
the FAQs and troubleshooting tips or learn about special printing solutions in the 'Solutions'
and 'Customer Education' sections.
Some Brother printer models are network standard. And some printer need optional kit to
use it with network.

ii
Trademarks
Brother is a registered trademark of Brother Industries, Ltd.
HP, HP/UX,JetDirect and JetAdmin are trademarks of Hewllet-Packard
Company.
DEC, DEC server, VMS and ULTRIX are trademarks of Digital Equipment
Corporation.
UNIX is a trademarks of UNIX Systems Laboratories.
Ethernet is trademark of Xerox Corporation.
Postscript is trademark of Adobe Systems Incorporated.
Netware is a trademark of Novell, Inc.
Apple, Macintosh, LaserWriter, and AppleTalk are trademarks of Apple
Computer, Inc.
IBM, LAN Server, and AIX are trademarks of International Business Machines
Corporation.
LAN Manager, Windows, and MS-DOS are trademarks of Microsoft Corporation.
NC-3100h BRAdmin are trademarks of Brother Industries.,Ltd.
All other brand and product names mentioned in this user’s guide are registered
trademarks or trademarks of respective companies.
Compilation and Publication
Under the supervision of Brother Industries Ltd., this manual has been compiled
and published, covering the latest product descriptions and specifications.
The contents of this manual and the specifications of this product are subject to
change without notice.
Brother reserves the right to make changes without notice in the specifications
and materials contained herein and shall not be responsible for any damages
(including consequential) caused by reliance on the materials presented, including
but not limited to typographical and other errors relating to the publication.
©2000 Brother Industries Ltd.
Shipment of the print server
If for any reason you must ship your print server, carefully package the print server to avoid
any damage during transit. It is recommended that you save and use the original packaging.
The print server should also be adequately insured with the carrier.
WARNING
When shipping the print server, put it into the unti-static bag to avoid a damage.

iii
For technical and operational assistance, please visit the Brother web site on
http://www.brother.com
If you have comments or suggestions, please write us at:
In Europe European Technical Services
1 Tame Street
Audenshaw
Manchester, M34 5JE
UK
In USA Printer Customer Support
Brother International Corporation
15 Musick
Irvine, CA 92618
In CANADA Brother International Corporation (Canada), Ltd.
- Marketing Dept.
1, rue Hôtel de Ville
Dollard-des-Ormeaux, PQ, Canada H9B 3H6
Fax-Back System
Brother Customer Service has installed an easy to use Fax-Back System so you can get
instant answers to common technical questions and product information for all Brother
products. This is available 24 hours a day, 7 days a week. You can use the system to send the
information to any fax machine, not just the one you are calling from.
Please call 1-800-521-2846 (USA) or 1-800-681-9838 (Canada) and follow the voice prompts to
receive faxed instructions on how to use the system and your index of Fax-Back subjects.
DEALERS/SERVICE CENTERS (USA only)
For the name of an authorized dealer or service center, call 1-800-284-4357.
SERVICE CENTERS (Canada only)
For service center addresses in Canada, call 1-800-853-6660
INTERNET ADDRESS
For technical questions and downloading drivers: http://www.brother.com and
http://solutions.brother.com

iv
TABLE OF CONTENTS
CHAPTER ONE UNIX PRINTING
PRINTING FROM UNIX/LINUX USING TCP/IP
Overview 1-1
TCP/IP 1-2
General TCP/IP UNIX Host Configuration 1-3
Linux Configuration 1-6
HP/UX Configuration 1-7
IBM RS/6000 AIX Configuration 1-8
Sun Solaris 2.x Configuration 1-9
SCO UNIX Configuration 1-10
DEC TCP/IP Servers for VMS(UCX) 1-11
TGV's Multinet 1-11
Wollongong's PATHWAY 1-11
IBM/AS4000 1-11
Other Systems 1-12
Other Sources of Information 1-13
CHAPTER TWO TCP/IP PRINTING
PRINTING FROM WINDOWS NT OR WINDOWS 2000,
LANSERVER AND WARP SERVER
Overview 2-1
Windows NT 3.5x/NT 4.0/2000 (TCP/IP) Configuration 2-2
Windows 2000 Printing (Printer Driver not yet installed) 2-3
Standard TCP/IP Port Printing 2-3

v
IPP Printing from Windows 2000 Clients 2-4
IPP printing from Windows 95/98/Me Clients 2-4
Windows 2000 Printing (Printer Driver already installed) 2-4
Windows NT 4.0 Printing 2-5
Windows NT 4.0 Printing (Printer Driver not yet installed) 2-6
Windows NT 4.0 Printing (Printer Driver already installed) 2-7
Windows NT 3.5x Printing 2-8
Windows NT 3.5x Printing (Printer Driver not yet installed) 2-8
LAN Server, OS/2 Warp Server Configuration 2-9
Server Configuration 2-9
Configuration of an OS/2 Server 2-9
Other Sources of Information 2-11
CHAPTER THREE PEER TO PEER PRINTING
HOW TO PRINT IN A WINDOWS 95/98/ME PEER TO PEER
NETWORK
Overview 3-1
TCP/IP Printing 3-2
Installing the Brother Peer to Peer Software 3-3
Associating to the printer 3-4
Adding a Second Brother LPR Port 3-4
Other Sources of Information 3-5
CHAPTER FOUR NETBIOS PEER TO PEER PRINTING
HOW TO PRINTING USING NETBIOS ON WINDOWS
95/98/ME/NT/2000, LAN SERVER AND OS/2 WARP SERVER
Overview 4-1
Print Server Configuration 4-2
Changing the workgroup/domain name using TELNET or BRCONFIG or a web
browser 4-3

vi
NetBIOS Port Monitor for Windows 95/98/Me, NT4.0/2000 4-4
Installing the Brother NetBIOS Port Monitor 4-4
Associating the printer 4-6
Windows 95/98/Me 4-6
Windows NT4.0/2000 4-6
Adding a Second NetBIOS Print Port 4-7
Windows 95/98/Me 4-7
Windows NT4.0/2000 4-7
LAN Server/OS/2 Warp Server Configuration 4-8
Server Configuration: 4-8
Workstation Configuration: 4-8
Other Sources of Information 4-9
CHAPTER FIVE HOW TO CONFIGURE INTERNET PRINTING
FOR WINDOWS 95/98/ME NT 4.0/WINDOWS 2000 INTERNET
PRINTING INSTALLATION
Overview 5-1
Brother Internet Print General Information 5-2
Brother Internet Print Configuring the Brother Print Server 5-3
Print Server Configuration Checklist 5-3
Brother Internet Print Using BRAdmin to Configure the Print Server 5-4
Brother Internet Print Using a Web Browser to configure the Print Server 5-5
Brother Internet Print Using TELNET to Configure the Print Server 5-6
Brother Internet Print Installing the BIP software on Windows
95/98/Me/NT4.0/2000 5-7
Setup from CD-ROM 5-7
Adding a Second Brother Internet Port 5-10
Windows 2000 IPP Printing 5-11
Specifying a different URL 5-12
Other Sources of Information 5-12

vii
CHAPTER SIX NOVELL NETWARE PRINTING
HOW TO CONFIGURE NOVELL NETWARE PRINTING
Overview 6-1
General Information 6-2
Creating a NDPS Printer Using NWADMIN for NetWare5 6-3
NDPS Manager 6-3
NDPS Broker 6-3
Creating a Printer Agent 6-4
Configuring Netware 3 and NetWare 4 systems 6-5
Configuring the Brother Print Server (Queue Server Mode in Bindery
emulation mode) using BRAdmin 6-6
Configuring the Brother Print Server (Queue Server Mode in NDS mode)
using BRAdmin 6-7
Configuring the Brother Print Server (Queue Server Mode in NDS mode)
using Novell NWADMIN and BRAdmin 6-8
Configuring the Brother Print Server (Remote Server Mode in NDS mode)
using Novell NWAdmin and BRAdmin 6-10
Configuring the Brother Print Server (Queue Server Mode in Bindery
emulation mode) using PCONSOLE and BRCONFIG 6-12
Configuring the Brother Print Server (Queue Server Mode in NDS mode)
using PCONSOLE and BRCONFIG 6-14
Configuring the Brother Print Server (Remote Printer Mode using PCONSOLE
and BRCONFIG 6-16
Other Sources of Information 6-19
CHAPTER SEVEN APPLETALK (ETHERTALK)
TCP/IP PRINTING PRINTING FROM A MACINTOSH
Overview 7-1
Macintosh Configuration 7-2
Operation 7-3

viii
How to Select the Print Server (AppleTalk/EtherTalk) 7-3
How to Select the Print Server (TCP/IP) 7-4
Changing the Configuration 7-6
Other Sources of Information 7-6
CHAPTER EIGHT DLC PRINTING
PRINTING FROM WINDOWS NT OR WINDOWS 2000
Overview 8-1
Configuring DLC on Windows NT/2000 8-2
Windows 2000 Printer Setup 8-3
Windows NT 4.0 Printer Setup 8-4
Windows NT 3.5x Setup 8-5
Configuring DLC on Other Systems 8-5
Other Sources of Information 8-6
CHAPTER ELEVEN WEB BASED MANAGEMENT
HOW TO USE A WEB BROWSER TO MANAGE YOUR DEVICE
Overview 9-1
How to connect to your printer using a Browser 9-2
Other Sources of Information 9-2
CHAPTER TWELVE TCP/IP CONFIGURATION
ASSIGNING TCP/IP INFORMATION
Overview 10-1
Using the printer front panel to allocate an IP address (printers with LCD
panels only) 10-2
Changing the IP Address using the BRAdmin application 10-3
Using BRAdmin and the IPX/SPX Protocol to change the IP address 10-4

ix
Using BRAdmin and the TCP/IP Protocol to change the IP address 10-4
Using DHCP to Configure the IP address 10-5
Using ARP to Configure the Print Server IP Address 10-6
Using RARP to Configure the IP Address 10-7
Using BOOTP to Configure the IP Address 10-8
Configuring the IP Address with DEC NCP or BRCONFIG 10-9
Changing the IP Address settings with the TELNET Console 10-11
Other Sources of Information 10-12
CHAPTER THIRTEEN TROUBLESHOOTING
Overview 11-1
Installation problems 11-2
Intermittent Problems 11-5
TCP/IP Troubleshooting 11-6
UNIX Troubleshooting 11-7
Windows NT/LAN Server (TCP/IP) Troubleshooting 11-9
Windows 95/98/Me Peer to Peer Print (LPR) Troubleshooting 11-9
Windows 95/98/Me Peer-to-Peer (HP JetAdmin compatible method)
Troubleshooting 11-10
Windows 95/98/Me/NT 4.0 Peer-to-Peer Print (NetBIOS) Troubleshooting 11-10
Brother Internet Print (TCP/IP) Troubleshooting 11-11
Windows 95/98/Me/2000 FTP/IPP Troubleshooting 11-12
Novell NetWare Troubleshooting 11-13
AppleTalk Troubleshooting 11-14
DLC/LLC Troubleshooting 11-15
Web Browser Troubleshooting (TCP/IP) 11-15

x
APPENDIX
Appendix A A-1
General Information A-1
Appendix B Using Services A-3
General A-3
Appendix C Reloading the Print Server Firmware A-4
General A-4
Reloading firmware using BRAdmin A-5
Reloading process A-6
Reloading using the FTP Protocol from a command prompt A-7
Reloading using the FTP Protocol from a Web Browser A-8
INDEX I-1

xi
IMPORTANT INFORMATION: REGULATIONS
Federal Communications Commission (FCC) Declaration of
Conformity
(For U.S.A. only)
Responsible Party: Brother International Corporation
100 Somerset Corporate Boulvard
Bridgewater, NJ 09907-0911, USA
TEL: [phone]
declares, that the products
Product Name: Brother Network Card (BR-net)
Model Number: NC-3100h
complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undersired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important
Changes or modifications not expressly approved by Brother Industries, Ltd. could
void the user’s authority to operate the equipment.

xii
Industry Canada Compliance Statement (For Canada only)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
DECLARATION OF CONFORMITY (EUROPE)
We, Brother Industries, Ltd.,
15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan
declare that this product is in conformity with the following normative documents.
Safety: EN 60950,
EMC: EN 55022 Class B, EN 55024
following the provisions of the Low Voltage Directive 73/23/EEC and the
Electromagnetic Compatibility Directive 89/336/EEC (as amended by 91/263/EEC
and 92/31/EEC).
Issued by: Brother Industries, Ltd.
Information & Document Company

CHAPTER 1 UNIX PRINTING
1-1
1
CHAPTER ONE
Unix Printing
11Printing from Unix/Linux using
TCP/IP
Overview
Brother print servers are supplied with the Transmission Control Protocol/Internet
Protocol (TCP/IP) protocol suite. Since virtually all UNIX host computers support
TCP/IP, this capability allows a printer to be shared on a UNIX Ethernet network. As
with all protocols, TCP/IP communications can proceed concurrently whilst other
protocols are active, this means that UNIX, NetWare, Apple, and other computers
can share the same Brother Print Server over an Ethernet network.
The Linux operating system uses the same setup procedures as standard Berkeley
UNIX systems. Refer to this chapter for a typical GUI based Linux installation.
Quick Tips:
1. The default IP address of Brother print servers is 192.0.0.192. To change it,
use the print front panel (if applicable), the BRAdmin application or let your
DHCP server allocate an IP address to the printer.
2. Refer to chapter 10 of this user guide to learn how to configure the IP
address on your printer.
3. The default password for Brother print servers is "access".
4. The default name for a Brother print server is usually BRN_xxxxxx (where
xxxxxx is the last six digits of the Ethernet address of the print server).
However, some Brother print servers may use the name BRF-xxxxxx or
BRO_xxxxxx.
5. When configuring the PRINTCAP file, pay particular attention to the service
names, BINARY_P1 and TEXT_P1

CHAPTER 1 UNIX PRINTING
1-2
TCP/IP
Brother Print Servers appear to the network as a UNIX host computer with a unique
IP address running the lpd, line printer daemon, protocol. As a result, any host
computer that supports the Berkeley remote LPR command can spool jobs to Brother
Print Servers without the need for any special software on the host computer. For
special applications, raw TCP ports are also available.
The Brother NC-3100h and NC-4100h print servers also support the FTP protocol.
This protocol can be used to send print jobs from Unix systems.
The Brother print server is pre-configured to run on a TCP/IP network with a
minimum of setup. The only mandatory configuration the print server is the
allocation of an IP address, which can be either automatically assigned using DHCP,
BOOTP etc., or manually assigned using the ARP command, BRAdmin, the printer
front panel (if applicable), etc.
For setting the IP address of the print server, refer to the quick print setup guide or to
chapter 10 of this user guide.

CHAPTER 1 UNIX PRINTING
1-3
General TCP/IP UNIX Host Configuration
The configuration process for most UNIX systems is described in the following
steps. As this process varies, we recommend that you refer to your system
documentation (or man pages) for additional information.
1. Configure the /etc/hosts file on each UNIX host that needs to communicate
with the print server. Use your favorite editor to add an entry to the
/etc/hosts file containing the IP address and node name of the device. For
example:
192.189.207.3 BRN_310107
The actual format of the entry may vary depending on your system, check your
system documentation and also note the format of other entries in the etc/hosts file.
The node name in this file does not necessarily need to be the same as the one that is
actually configured into the Brother print server (the name that appears on the printer
configuration page), however, it is good practice to make the names the same. Some
operating systems, such as HP/UX, do not accept the "_" character in the default
name, for these systems you must use a different name).
In any case, the node name in the /etc/hosts file must match the node name in the
/etc/printcap file.
Some systems such as HP/UX and AIX allow you to enter the IP address as the host
name when setting up the print queue. If this is the case, you do not need to configure
the hosts file.

CHAPTER 1 UNIX PRINTING
1-4
2. Choose which print server service you want to use. There are several types
of services available on Brother Print Servers. Binary services pass data
through unmodified and are therefore required for PCL or PostScript
rasterized graphics printouts. Text services add a carriage return at the end of
each line for proper formatting of UNIX text files (which end in linefeed and
do not have carriage returns). The text service can also be used for non-
rasterized graphics, such as ASCII PostScript graphics or many types of
PCL graphics.
Choose one of the available services (a service name will be used in step 3):
BINARY_P1 Binary data
TEXT_P1 Text data (CR added)
You may set up multiple print queues on your UNIX host computer for the
same print server, each one with a different service name (for example, one
queue for binary graphics jobs and one for text jobs). Refer to Appendix B
for additional information on using services.
3. Configure the /etc/printcap file on each host computer to specify the local
print queue, the print server name (also called remote machine or rm), and
the print server service name (also called remote printer, remote queue, or
rp), and the spool directory.
This step applies to the majority of UNIX systems, including Linux, Sun OS (but not
Solaris 2.xx), Silicon Graphics (lpr/lpd option required), DEC ULTRIX, DEC
OSF/1, and Digital UNIX. SCO UNIX users should follow these steps, but should
also refer to the SCO UNIX Configuration section. Users of RS/6000 AIX, HP/UX,
Sun Solaris 2.xx, and other systems that do not use the printcap file should skip to
section 3-a. SCO user’s should also skip to section 3a (SCO uses the printcap file,
but this file is automatically configured via the rlpconf command)

CHAPTER 1 UNIX PRINTING
1-5
An example of a typical printcap file:
laser1|Printer on Floor 1:\
:lp=:\
:rm=BRN_310107:\
:rp=TEXT_P1:\
:sd=/usr/spool/lpd/laser1:
Make sure this information is added to the end of the printcap file. Also make sure
that the last character in the printcap file is a colon ":"
This will create a queue named laser1 on the host computer that communicates to a
Brother print server with a node name (rm) of BRN_310107 and a service name (rp)
of TEXT_P1 printing text files to a Brother printer through spool directory
/usr/spool/lpd/laser1. If you are printing binary graphics files, you would
use the service BINARY_P1 instead of TEXT_P1.
The rm and rp options are not available on some UNIX systems, so if necessary
check your documentation (or man pages) to determine the equivalent options.
Users of Berkeley-compatible UNIX systems can use the lpc command to obtain the
printer status:
%lpc status
laser1:
queuing is enabled
printing is enabled
no entries
no daemon present
Users of AT&T-compatible UNIX systems can generally use the lpstat or rlpstat
commands to obtain similar status information. Because this procedure varies from
system to system, refer to your system documentation for the exact usage.
4. Skip this section if you have completed Step 3, unless you have an SCO
UNIX system.
If you have an HP/UX system, IBM RS/6000 AIX computer, or Sun Solaris
2.xx, there is no printcap file. This is also true for some other AT&T-based
UNIX systems, as well as many VMS-based TCP/IP software packages (for
example, UCX, TGV Multinet, etc.). On SCO systems, there is a printcap file,
but it is automatically configured by the rlpconf command. Most of these
systems generally use a printer setup program to define the service name (remote
printer), the print server name (remote machine) or IP address, and the local
queue name (spool directory). Refer to the appropriate section depending on
your version of Unix.

CHAPTER 1 UNIX PRINTING
1-6
Linux Configuration
If you do not wish to use the command line interface to configure your Linux
distribution, you may wish to use the Linux Printer System Manager application on
your GUI. To do this, do the following:
1. From the Linux Printer System Manager screen, click the "Add" button.
2. You will now be asked to specify which Printer type you are using, select
the "Remote Unix (lpd) Queue" option and click "OK".
3. You must now specify the remote host name, remote queue name and the
input filter to use.
4. The "Remote Host" name is the IP address of the printer, or the name from
the hosts file which corresponds to the IP address of the printer.
5. The "Remote Queue" name is the service name that the printer will use when
processing the data. Generally we recommend that you use the name
"BINARY_P1", however, if you are planning to send text documents that do
not have a carriage return and a line feed, then use "TEXT_P1".
6. Select the appropriate "Input Filter" from the list of available printers on
your particular build of Linux.
In order to make your settings work, select the "Restart lpd" option. As soon as the
lpd server restarts, you will be able to send printed documents from your server.

CHAPTER 1 UNIX PRINTING
1-7
HP/UX Configuration
In the case of HP/UX10.xx, the sam program is used to set up the remote printer. The
steps are as follows:
1. Execute the sam program. From the list of options, select Printers and
Plotters
2. Select LP Spooler
3. Select Printers and Plotters
4. Select Actions and then Add Remote Printer/Plotter
5. Enter any name as the Printer Name (this will be the name of the print
queue)
6. Enter the IP address of the print server as the Remote System Name
7. Enter the desired print server service name as the Remote Printer Name
8. Check the box next to Remote Printer is on BSD system
9. You may accept the default values for the remaining items.
10. Click OK to configure the printer
You should now be able to print using the lp-d command with the printer name.
If you are using the HP distributed print service, the configuration procedure is
slightly different because you are sending the print jobs to a file server, which in turn
spools the job to the print server. You must therefore know the name of the file
server (spooler host) in addition to the above information. You will add a physical
and a remote printer and a remote printer, and then assign a logical printer to the
remote printer (a unique name that does not match any other name). To print, use the
lp -d command with the logical printer name.
Earlier versions of HP/UX use similar procedures to 10.xx users:
1. Enter sam and select Peripheral Devices and then Add Remote Printer (not
Networked printer)
2. Enter the following remote printer settings (the other settings do not matter):
3. Line printer name (user-selectable)
4. Remote system name (the print server name; must match what is in hosts file
or use print server IP address)
5. Remote printer queue (Printserver binary or text service name, e.g.
BINARY_P1 or TEXT_P1).
6. Remote Printer is on a BSD System (Yes)

CHAPTER 1 UNIX PRINTING
1-8
IBM RS/6000 AIX Configuration
The RS/6000 AIX operating system uses the smit program to set up the remote
printer. The procedure is as follows for AIX 4.0 and later:
1. Enter smit and select "devices"
2. Select "Printer/Plotter"
3. Select "Print Spooling"
4. Select "Add a Print Queue"
5. Select "Remote"
6. Enter the following Remote Printer Settings:
Name of queue (user selectable)
Host name of Remote Printer (print server name; must match name in
/etc/hosts file or use the print server IP address)
Name of queue on remote printer (print server binary or text service name,
eg. BINARY_P1 or TEXT_P1).
Type of print spooler. BSD (press the LIST button and choose BSD)
The procedure for pre-V4.0 systems is as follows.
1. Enter smit and select "devices"
2. Select "printer/plotter"
3. Select "manage remote printer subsystem"
4. Select "client services"
5. Select "remote printer queues"
6. Select "add a remote queue"
7. Enter the following remote queue settings:
8. Name of queue to add (user selectable)
9. Activate the queue (Yes)
10. Destination host (print server name; must match name in /etc/hosts file or
use the print server IP address)
11. Name of queue on remote printer (print server binary or text service name,
eg. BINARY_P1 or TEXT_P1).
12. Name of device to add (user selectable; for example lp0)