Broyhill CASTILLO BL-FP-072-001 User manual

Page 1 of 16
Determine you have adequate space for assembly.
Assembly by two adults is recommended.
Assemble on soft surfaces to prevent damage to product finish.
Keep children away during assembly. This item contains small parts which can be swallowed
by children.
Do not discard any of packaging until you have checked that you have all parts and hardware.
Retain the assembly instructions for future reference.
The manufacturer will not accept responsibility for unauthorized repairs or modifications to
this product.
This product is for residential use only, not for commercial use.
A Phillips head screw driver is necessary for assembly but is not included.
Wipe with a damp cloth. Use Furniture polish or lemon oil on the wood as needed.
Avoid prolonged exposure to moisture.
Do not scratch or chip the finish.
Do not put hot objects which are more than 80 degrees Fahrenheit directly on the surface.
Check bolts/screws periodically and tighten if necessary.
To prolong the life of product we recommend storage in a dry area when not in
use or during austere weather conditions.
To prevent serious injury or death, this product is equipped with a wall anchoring system.
Before this product can be used, the wall anchoring system must be installed as directed in
the assembly instructions.
Should this product become damaged, and/or components are broken or missing,
DO NOT USE.
This product will burn if left in contact with flame source.
WARNING: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
WARNING - Death or serious injury may occur when children climb on audio and/or video
equipment furniture. A remote control or toys placed on the furnishing may encourage
a child to climb on the furnishing and as a result the furnishing may tip over on to the child.
WARNING - Relocating audio and/or video equipment to furniture not specifically designed
to suppirt audio and/or video equipment may result in death or serious injury due to the
furnishing collapsing or over turning onto a child.
GENERAL BEST PRACTICES FOR ASSEMBLY:
WARNINGS:
MAINTENANCE:

PARTS LIST
Page 2 of 16
A
B
C
D
E
F
G
H
I
J
L
M
N
O
P
Q
R
S
T
U
K Z
Top Panel
Top Left side Panel
Top Left Middle Panel
Top Crossbar
Center Back Panel
Center Middle Panel
Bottom Left Side Panel
Bottom Left Middle Panel
Center Crossbar
Top Right Middle Panel
1
1
1
1
1
1
1
1
1
Bottom Right Middle Panel
1
1
1
1
Door
Side Back Panel
Adjustable Shelves
Bottom Crossbar
Bottom Panel
Left Drawer
Fireplace Remote Control
1
2
2
2
1
1
1
1
1
Right Drawer
Top Right side Panel
Bottom Right Side Panel
K
Z
A
B
CDE
U
G
H
I
J
N
L
M
O
O
P
P
Q
Q
R
S
T
F

HARDWARE LIST
Page 3 of 16
8 PCS
1
2
3
4
5
6
7
1 PC
38 PCS
8 PCS
8 PCS
4 PCS
8
6 PCS
9
4 PCS
10
24 PCS
11
2 PCS
2 PCS
12
13
4 PCS
14
15
8 PCS
16
2 PCS
17
18
4 PCS
2 PCS
2 PCS
4 PCS
19
20
4 PCS
2 PCS
Bolt Ø1/4"*32mmL
Spring Washer
Ø1/4"
Flat Washer
Ø1/4"
Allen Key 4mmL
Wood Dowel Ø8*30mmL
Screw Ø7*19mmL
Screw Ø 7*15mmL
Hinge
Handle Bolt
Ø5-32"*25mmL
Door Handle
Shelf Pin
Knob
Anti-Tipping Strip 25*230mmL
Wall Anchor
Ø8.5*30mmL
Screw Ø8*28mmL
Flat Head Screw Ø 7*16mmL
Knob Bolt
Ø5/32"*35mmL
Plastic Block
Screw Ø 7*12mmL
Door Stopper

Page 4 of 16
STEP 1
x4 x4 x4
x1
Hardware needed
12 3
4
With assistance, place the Bottom Panel (S) upside down
on a smooth surface. Attach the Bottom Crossbar (R) to
Bottom Panel (S) with Flat Washer (3), Spring Washer (2)
and Bolts (1) using Allen Key (4). Fully tighten all bolts.
Return Bottom Panel (S) to upright position.
S
R
4
1
2
3

Page 5 of 16
STEP 2
Hardware needed
x8
5
Closed
Open
I
N
J
M
S
Insert Wood Dowel (5) into Bottom Panel (S). Align the holes in Bottom
Right Side Panel (N) and slide to place. Make sure all the latches are
in open position so the pins are aligned with their corresponding holes
before inserting them. Once inserted, close all the latches until they are
flush to fully secure the panels in place.
Repeat process to attach the Bottom Left Side Panel (I), Bottom Right
Middle Panel (M) and Bottom Left Middle Panel (J) to Bottom Panel (S).

Page 6 of 16
STEP 3
P
P
L
Hardware needed
x2
5
Insert Wood Dowel (5) into holes of Bottom Middle Panels as shown.
Align the holes in Center Crossbar (L) with the inserted dowels and
lower into place.
Insert one Side Back Panel (P) down along the groove of Bottom Left
Side Panel (I) and Bottom Left Middle Panel (J). Insert the remaining
Side Back Panel (P) down along the groove of Bottom Right Side Panel
(N) and Bottom Right Middle Panel (M).

Page 7 of 16
STEP 4
Hardware needed
x8
5
Place the Door Stop (19) on the bottom of Center Middle Panel
(H) as shown. Secure with Screw (20) using Phillips Screwdriver.
Fully tighten screws. Repeat steps for the remaining Door
Stopper (19). Return panel upright position with assistance.
Insert Wood Dowel (5) into hole of Bottom Right Side Panel (N),
Bottom Right Middle Panel (M), Bottom Left Middle panel (J)
and Bottom Left Side Panel (I). With assistance, set the Center
Middle Panel (H) over the Bottom Right Side Panel (N), Bottom
Right Middle Panel (M), Bottom Left Middle panel (J) and
Bottom Left Side Panel (I) and lower into place. Make sure all
the latches are in the open position so the pins are aligned with
their corresponding holes before inserting them. Once inserted,
close all the latches until they are flush to fully secure the panels
in place.
Not included
x2
x4
20
19
H
Closed
Open
H
19
20
5

Page 8 of 16
STEP 5
Hardware needed
x20
5
Closed
Open
C
D
E
B
F
Insert Wood Dowel (5) into hole of Top Cross Bar (D). Align the hole of
Top Left Middle panel (C) and Top Right Middle Panel (E) with the inserted
dowels and slide into place as shown.
Insert Wood Dowel (5) into hole of Center Middle Panel (H), align the
holes in the Top Left Side Panel (B), Top Right Side Panel (F) and the
assembled parts with the inserted dowles as shown and slide into place.
Make sure all the latches are in open position so the pins are aligned with
their corresponding holes before inserting them. Once inserted, close all
the latches until they are flush to fully secure the panels in place.
H

Page 9 of 16
STEP 6
Closed
Open
G
A
Hardware needed
x8
5
Insert Center Back Panel (G) down along the groove of Top Left Side
Panel (B), Top Left Middle Panel (C), Top Right Middle Panel (E) and
Top Right Side Panel (F).
Insert Wood Dowel (5) into holes of Top Left Side Panel (B), Top Left
Middle Panel (C), Top Right Middle Panel (E) and Top Right Side Panel
(F). With assistance, align the Top Panel (A) into place as shown.
Make sure all the latches are in open position so the pins are aligned
with their corresponding holes before inserting them. Once inserted,
close all the latches until they are flush to fully secure the panels in place.

STEP 7
x4 x24 x4
x2
Hardware needed
910 11
12
109
12
11
Not included
Page 10 of 16
Attach Hinge (9) to Door (O) with Flat Head Screw (10)
using Phillips Screwsdriver. Fully tighten screws.
With assistance, center the Door (O) along the edge of
Bottom Right Side Panel (N). Attach Hinge (9) to Bottom
Right Side Panel (N) with Screw (10). Fully tighten screws.
Repeat the process to attach the remaining Door (O) to the
Bottom Left Side Panel (J). Attach Door Handle (12) to Door
(O) with Door Handle Bolt (11). Fully tighten bolts.
Repeat step to attach remaining handle to remaining door.

STEP 8
x8
15
Page 11 of 16
15
Insert Shelf Pin (15) in to the pre-drilled holes as
shown in diagram.
Place Adjustable Shelf (Q) onto the shelf pins.
You can adjust the position of shelf as needed.

STEP 9
x2
Hardware needed
14
Not included
x2
13
When you need to
pull out the drawer,
Please refer to the
Diagram to operate
14
13 124
3
Page 12 of 16
Attach Knob (14) to Right Drawer (U) with Knob Bolt (13) using
Phillips Screwdriver. Fully tighten bolts.
Repeat the process to attach Knob (14) to Left Drawer (T).
Attention: before assembly, please make sure to adjust the metal
piece/ball bearing to the front of the drawer glide for both left and
right side slider.
Align the track on the drawer with the track on the Mantel. Gently
push drawer into position. Be sure to apply equal pressure to both
sides while inserting the drawer. If drawer sticks or jams, then remove
the drawer and reinsert it according to direction.

x6
Hardware needed
8
Not included
67
x8 x8
Page 13 of 16
STEP 10
K8
Place the Plastic Block (6) into the corner of Side back
panel as shown, insert Screw (7) into the pre-drilled holes
and secure with Phillips Screwdriver. Fully tighten screws.
Repeat the step for the remaining Plastic Block (6).
Insure all Plastic Blocks are used to secure both side back
panels in place.
Insert the fireplace (K) into the opening in the back of
assembled Mantel. With Assistance, center Fireplace (K) in
the opening and secure to the Mantel with Screw (8) using
Phillips Screwdriver. Fully tighten screws.
7
6

STEP 11
18
16
16
18
17
3
3
Hardware needed
x4 x2
316
WALLWALL Not included
Not included
WALL
x2 x4
17 18
Not included
Page 14 of 16
Attach the Anti-tipping strips (16) to the back top of the mantel with
Screw (18) and Flat Washer (3). With assistance, place the Mantel
in the desired location and mark the wall just below the spot where
the Aniti-tipping Strips are attached to the mantel.
Remove the Mantel.
Drill holes in the marked locations on the wall and insert the Wall
Anchor (17). Place the Mantel back into position leaving room to
attach the Anti-tipping Strips (16) to the Wall Anchor (17) with Screw
(18) and Flat Washer (3). Fully tighten Screws.
Move the Mantel tight against the wall.
NOTE: Please insure Fireplace insert is plugged in and working
correctly before securing the Anti-tipping Strips to the Wall Anchors.

WARNING
The maximum diagonal Plasma/LCD television screen size is 65inch (165.10cm).
For use with televisions weighing 135 lbs. (61.23 kg) or less. Using larger or
heavier televisions may cause instability or tip-over which lead to serious injury
or even death.
WARNING - Death or serious injury may occur when children climb on audio
and/or video equipment furniture. A remote control or toys placed on the furnishing
may encourage a child to climb on the furnishing and as a result the furnishing
may tip over on to the child.
WARNING - Relocating audio and/or video equipment to furniture not specifically
designed to suppirt audio and/or video equipment may result in death or serious
injury due to the furnishing collapsing or over turning onto a child.
MAXIMUM LOAD 135LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
MAXIMUM LOAD 20LBS
GRAND ART FURNITURE CO., LTD
ADRESS: D17 STREET, MY PHUOC I INDUSTRIAL PARK,
BEN CAT DISTRICT, BINH DUONG PROVINCE, VIETNAM
Page 15 of 16

PRINTED IN VIETNAM
ASSEMBLY IS COMPLETED
Page 16 of 16