BTC US-FF432 User manual

Task
Instruction Manual
Table & Floor Light
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and
contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
Ceramic Table
US-FT431
Table
US-FT378
Solo Table
US-FT427
Small Table
US-FT402
Ceramic Floor
US-FF432
Floor
US-FF379
Overreach
US-FF393
v1.2-04.19

Task Table Light 120V ac 60Hz Adjusting FittingIP20
Safety Instructions
Cleaning and Maintenance
- Ensure the lamp type and max wattage is followed- do not exceed. Take care not to overtighten
lamp.
- Do not touch the lamp (bulb) or lamp holder while in operation, as both become very hot.
- Turn off and unplug fitting, leaving lamp to cool before changing lamp. Dispose of old lamps
carefully.
- Adjust light fitting only when power to the fitting is off and has been left to cool.
- Never leave a fitting without a lamp in position.
- Keep light fitting away from combustible materials such as soft furnishings.
- Ensure children do not play with the light fitting.
- Ensure the light is positioned on a solid, level and non-slip surface and make sure the position of
the cable does not pose a trip hazard.
- If the electrical flex or electrical components become damaged at any point, the fitting must be
unplugged from the power supply immediately and not operated until the damaged parts are
fixed/replaced.
- For use in a dry, indoor environment only. Ensure the fitting does not come into contact with any
liquids.
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Bone
china can be cleaned by hand, using a soft damp cloth with a diluted mild detergent (nonabrasive) if
necessary. Switch off power to the fitting before cleaning.
The Task range of lights can be moved, angled or adjusted bringing greater flexibility and creative
scope, while focussing a high level of illumination directly where it is needed. Shades can be angled
and swivelled, to throw either a concentrated pool or illuminate a larger area.
When adjusting the clamp, ensure it is supported with other hand and take care not to loosen the
handle too far, as this can cause the handle to detach from the clamp body and fall from the fitting,
causing damage/injury.
!
Adjusting Position of Arm
1
2
3
Loosen the handle of the clamp, by gently turning clamp by one
quarter-turn in an anti-clockwise direction.
Position arm into desired position, then secure by tightening
handle of clamp firmly. Do not overtighten.
The arm may be rotated, when held in the clamp by gently
twisting the arm while holding the clamp in position.
Adjusting Height of Arm
1
2
Loosen the handle of the clamp, by gently turning clamp almost one
full turn in an anti-clockwise direction.
While supporting both clamp and arm, position arm at desired height,
then secure by tightening handle of clamp firmly. Do not overtighten.
Adjusting Shade
-
-
The swivel joint allows great flexibility of movement, allowing the
shade to be tilted or rotated into position as desired.
Adjust angle of shade by gently pivoting shade on swivel joint (4)-
tilting up/down up to 90˚ or rotating up to 180˚ in either direction.
2
1
3
1
2
4
US-FT402 Small Table
US-FT378 Table
US-FT431 Ceramic Table
US-FT427 Solo Table
US-FF432 Ceramic Floor
US-FF379 Floor
US-FF393 Overreach
(a) US-FF432/379, US-FT402/378/431/427
(b) US-FF393
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
E26 A BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE




INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX (a)
15W
42W
10W
100W MAX (b)
20W
70W
18W
ENG WARNING – RISK OF FIRE AND ELECTRIC SHOCK.
SUITABLE FOR DRY LOCATIONS ONLY
FR ATTENTION – RISQUE D’INCENDIE, RISQUE DE CHOC.
POUR EMPLACEMENTS SECS SEULEMENT