Buffalo FS440 User manual

Model • Modèle • Modell • Modello • Modelo • Malli:
FS440/FS441/FS442
Stick Blender
Instruction manual
UK Stick Blender
Instruction manual
2DE Stabmixer
Bedienungsanleitung
20
NL Staafmixer
Handleiding
8IT Frullatore ad Immersione
Manuale di istruzioni
26
FR Mixeur en bâton
Mode d'emploi
14 ES Batidora
Manual de instrucciones
32
FS440-FS441-FS442_ML_A5_v1_20211118.indb 1FS440-FS441-FS442_ML_A5_v1_20211118.indb 1 2021/11/18 16:322021/11/18 16:32

2
UK
Safety Instructions
The blender is a dangerous appliance and must only
be used by trained personnel in accordance with these
instructions.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
• The protective blade guard and shaft of this appliance
are designed for submersion in liquids or half-liquid
mixtures. To protect against risk of electrical shock,
never submerge any other portion of this unit in any
liquid.
• Blade is sharp – handle carefully.
• DO NOT use with loose or damaged blades.
• The use of accessory attachments not recommended or sold
by BUFFALO may cause fire, electric shock, or injury, which
will invalidate your guarantee.
• DO NOT remove food from the appliance until the blending
attachment have come to a complete stop.
• Avoid contacting moving parts. Keep hands, hair, clothing and
utensils away from blade and mixing container while operation
to prevent the possibility of severe injury to persons and/or
damage to the appliance.
FS440-FS441-FS442_ML_A5_v1_20211118.indb 2FS440-FS441-FS442_ML_A5_v1_20211118.indb 2 2021/11/18 16:322021/11/18 16:32

3
UK
• DO NOT operate the unit if damaged.
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT attempt to blend items that this machine is not
designed for. This can damage the blending attachments.
• Always switch off and disconnect the power supply to the
appliance when not in use, before cleaning and before putting
on or taking off parts.
• Not suitable for outdoor use.
• Keep all packaging away from children. Dispose of the
packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a
BUFFALO agent or a recommended qualified technician in
order to avoid a hazard.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
• DO NOT let cord hang over edge of table or counter, or touch
hot surfaces.
• BUFFALO recommend that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Insulation Continuity and Functional Testing.
• BUFFALO recommend that this product is connected to a circuit
protected by an appropriate RCD (Residual Current Device).
Product Description
FS440 - Buffalo Variable Speed Stick Blender - 300mm
FS441 - Buffalo Variable Speed Stick Blender - 400mm
FS442 - Buffalo Variable Speed Stick Blender - 500mm
FS440-FS441-FS442_ML_A5_v1_20211118.indb 3FS440-FS441-FS442_ML_A5_v1_20211118.indb 3 2021/11/18 16:322021/11/18 16:32

4
UK
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of
this machine will provide the best possible performance from your BUFFALO product.
This appliance is intended for use in kitchens of restaurants, canteens and so on when mixing and
liquidising and giving soups and sauces a perfect consistency. The unit can be used directly in a container
to mix everything from fish soups, stews, creams and salad dressings to pancake mixes, pastes, sauces,
mayonnaise and alike.
Pack Contents
The following is included:
• Power pack • Emulsifying blade
• Detachable shaft with triangle blade pre-mounted • Blade removal kits
• Instruction manual
BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.
Operation
Handle
ON/OFF button
Safety button
Variable Speed Dial
LOCK button
Detachable shaft
Blade guard
Power pack
FS440-FS441-FS442_ML_A5_v1_20211118.indb 4FS440-FS441-FS442_ML_A5_v1_20211118.indb 4 2021/11/18 16:322021/11/18 16:32

5
UK
Assembly
Before assembly, ensure to
• Disconnect the power pack from the
power supply.
• Clean all removable parts thoroughly.
1. Align and insert the pins of the shaft into the
lock sleeve of the power pack.
2. Screw the shaft as arrow shown into the power
pack securely.
Pin
Shaft
Sleeve
Blending
1. Ensure the ON/OFF button (3) is in the
released position.
2. Select speed using the variable speed dial (1).
3. Connect the appliance to the power supply.
4. Press and hold the safety button (2) with one
hand.
5. Press and hold the ON/OFF button to start
the blender. Now you can release the safety
button.
6. To stop the blender, just release the ON/
OFF button. The safety button will release
automatically.
3
2
1
4
Continuous blending
Follow steps1 to 5 as above, then:
1. While the ON/OFF button is in the depressed
position, press the LOCK button (4).
2. Now release the ON/OFF button. The appliance
will function continuously.
3. To stop the appliance, just press the ON/OFF
button once.
• For greater control, we recommend
holding the blender by the handle
and the bottom of the power pack.
Furthermore, it is recommended to tilt
the bender slightly to prevent the blade
guard from touching the bottom of the
container.
• Always make sure that the blade
guard is sufficiently immersed to avoid
splashing and that the air vents of the
motor unit does not come into contact
with any liquid. For optimum efficiency,
two thirds of the shaft should be
immersed during preparation.
• During use, the stainless steel shaft
may become hot. Take care not to touch
it.
• It is advisable to start at a low speed.
Removing the lodged food
If a piece of food gets lodged in the protective
blade guard surrounding the metal blade, please
follow the instructions below:
1. Turn off blender, disconnect from power supply
and let it come to a complete stop.
2. Remove the shaft from the power pack.
3. Use a spatula to carefully remove the food
lodged in the blade guard. The blade is
sharp - Never attempt to use fingers to
remove any lodged object.
4. Re-attach the shaft, plug unit back in and
continue blending.
FS440-FS441-FS442_ML_A5_v1_20211118.indb 5FS440-FS441-FS442_ML_A5_v1_20211118.indb 5 2021/11/18 16:322021/11/18 16:32

6
UK
Changing the blade
• Warning: Before removing blade,
ensure to turn off blender, disconnect
from power supply and let it come to a
complete stop.
• Blade is sharp - handle carefully.
• A triangle blade is pre-mounted on the shaft.
• A round emulsifying blade is also supplied,
ideal for use with nursery/special diets to
prepare purée of vegetables, porridge, raw
carrot purée, fruit creams, etc. To use it:
1. Remove the shaft from the power pack.
2. Using the triangle blade removal kit, with
the round end holding the shaft top while
the triangle end covering the blade then
unscrewing, remove the triangle blade from
the shaft.
Blade removal kit
3. Mount the emulsifying blade securely using the
emulsifying blade removal kit.
Cleaning, Care &
Maintenance
Warning: Always ensure to
disconnect unit from power supply,
let it cool down and come to a
complete stop before cleaning.
• After use, clean in time to prevent food from
sticking to surfaces.
• Clean the power pack surface using a damp
cloth. Always wipe dry after cleaning. Never
immerse the motor part in water or rinse it
under running water.
• Do not allow any moisture to enter the interior
via any ventilation slots.
• The appliance contains on user serviceable
parts. A BUFFALO dealer or qualified technician
should carry out repairs if required.
Cleaning the shaft, blade guard, and
blade
• Remove the food residue as much as possible.
• Place the shaft and blade guard into a
container with water, then switch on for a few
seconds for thorough cleaning.
• WARNING: Always dry the blades well after
cleaning to avoid spotting.
• It is vital to clean thoroughly between each job
using a detergent or disinfectant, but never
use pure bleach. For plastic parts, do not use
detergents that are too alkaline.
Troubleshooting
Fault Probable Cause Solution
The unit is not
working The unit is not switched on Check the unit is plugged in correctly and switched on
Plug or lead is damaged Call BUFFALO agent or qualified Technician
Fuse in the plug has blown Replace the plug fuse
Power supply Check power supply
Unit stops working
suddenly Overheating protection is activated Release the ON/OFF button, then unplug. Wait a few minutes for the motor to cool down and the
thermal safety mechanism to reset, then restart
Loud noise Blade not correctly fitted Release the ON/OFF button, then unplug. Re-install
the blade
FS440-FS441-FS442_ML_A5_v1_20211118.indb 6FS440-FS441-FS442_ML_A5_v1_20211118.indb 6 2021/11/18 16:322021/11/18 16:32

7
UK
Technical Specifications
Model Voltage Power Current Blending
Capacity Shaft length Dimensions h x Ø mm Weight
FS440 220-240V~
50Hz 500W 2.2A 60L 300mm 708 x 100 3.60kg
FS441 500W 2.2A 100L 400mm 808 x 100 4.00kg
FS442 500W 2.2A 120L 500mm 908 x 100 4.20kg
Electrical Wiring
This appliance is supplied with a 3 pin BS1363 plug and lead.
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The WEEE logo on this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and
environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the product supplier, or the local authority responsible for
waste disposal in your area.
BUFFALO parts have undergone strict product testing in order to comply
with regulatory standards and specifications set by international,
independent, and federal authorities.
BUFFALO products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of BUFFALO.
Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to
change specifications without notice.
FS440-FS441-FS442_ML_A5_v1_20211118.indb 7FS440-FS441-FS442_ML_A5_v1_20211118.indb 7 2021/11/18 16:322021/11/18 16:32

8
NL
Veiligheidstips
De mixer is een gevaarlijk apparaat en mag alleen
worden gebruikt door ervaren personeel met
inachtneming van deze instructies.
• De installatie en eventuele reparaties dienen door een
gekwalificeerde onderhoudsmonteur/vakman uitgevoerd te
worden. Verwijder geen componenten of servicepanelen van
dit product.
• Raadpleeg en volg de plaatselijke en nationale regelgeving op
m.b.t. tot het volgende:
- Wetgeving inzake gezondheid en veiligheid op het werk
- Werkregels
- Brandpreventie
- IEE-bedradingsvoorschriften
- Bouwvoorschriften
• De beschermkap en mixstaaf van dit apparaat zijn
ontworpen voor onderdompeling in vloeistoffen of
mengsels, die voor een gedeelte uit vloeistoffen
bestaan. Om het risico op elektrische schokken te
voorkomen, mag u nooit een ander deel van dit
apparaat in een vloeistof onderdompelen.
• Het mes is scherp – ga er voorzichtig mee om.
• Niet gebruiken met losse of beschadigde messen.
• Het gebruik van accessoires, die niet door BUFFALO worden
aanbevolen of verkocht, kan brand, elektrische schokken of
letsel veroorzaken, waardoor uw garantie ongeldig wordt.
• Haal het voedsel pas uit het apparaat als het opzetstuk voor
mixen volledig tot stilstand is gekomen.
• Vermijd contact met bewegende delen. Houd handen, haar,
kleding en keukengerei tijdens het gebruik uit de buurt van
het mes en de mengkom om de mogelijkheid van ernstig letsel
aan personen en/of schade aan het apparaat te voorkomen.
FS440-FS441-FS442_ML_A5_v1_20211118.indb 8FS440-FS441-FS442_ML_A5_v1_20211118.indb 8 2021/11/18 16:322021/11/18 16:32

9
NL
• Gebruik het apparaat niet als het beschadigd is.
• Gebruik GEEN waterstraal-/hogedrukreinigers om het apparaat
schoon te maken.
• Probeer geen voorwerpen te mixen, waarvoor deze machine
niet is ontworpen. Dit kan de opzetstukken voor het mixen
beschadigen.
• Schakel het apparaat altijd uit en koppel de stroomvoorziening
los wanneer deze niet in gebruik is, voor het schoonmaken en
voor het plaatsen of verwijderen van onderdelen.
• Niet geschikt voor gebruik buitenshuis.
• Laat verpakkingsmateriaal niet binnen handbereik van kinderen.
Verpakkingsmateriaal in overeenstemming met de regelgeving
van de plaatselijke overheden als afval laten verwerken .
• Indien de stroomkabel beschadigd raakt, dient men deze
door een BUFFALO -monteur of aanbevolen vakman te laten
vervangen om gevaarlijke situaties te voorkomen.
• Dit apparaat is niet bedoeld voor gebruik door personen met
lichamelijke, zintuiglijke of mentale beperkingen (inclusief
kinderen) of door personen met gebrek aan ervaring of kennis,
tenzij zij hierin worden begeleid of zijn opgeleid in het gebruik
van het apparaat door een persoon, die verantwoordelijk is
voor hun veiligheid.
• Men dient er toezicht op te houden dat kinderen niet met het
apparaat spelen.
• Voorkom dat het snoer over de rand van de tafel of toonbank
hangt of hete oppervlakken raakt.
• BUFFALO beveelt aan dat dit apparaat periodiek (minstens
jaarlijks) door een bevoegde persoon wordt getest. Tests
moeten omvatten, maar zijn niet beperkt tot: visuele inspectie,
polariteit, isolatie continuïteit en functionele test.
Productomschrijving
FS440 - BUFFALO staafmixer met variabele snelheid - 300mm
FS441 - BUFFALO staafmixer met variabele snelheid - 400mm
FS442 - BUFFALO staafmixer met variabele snelheid - 500mm
FS440-FS441-FS442_ML_A5_v1_20211118.indb 9FS440-FS441-FS442_ML_A5_v1_20211118.indb 9 2021/11/18 16:322021/11/18 16:32

10
NL
Inleiding
Neem de tijd om deze handleiding aandachtig door te lezen. Correct gebruik en onderhoud van deze
machine waarborgt de beste prestatie van uw Buffalo product.
Dit apparaat is bedoeld voor het gebruik in keukens van restaurants, kantines etc., bij het mixen en
vloeibaar maken en het ervoor zorgen, dat soepen en sauzen een perfecte samenhang tonen. Het
apparaat kan direct in een kom worden geplaatst om alles te mixen, van vissoepen, stoofschotels, crèmes
en slasauzen tot pannenkoekenmixen, pasta’s, sauzen, mayonaise en dergelijke.
Verpakkingsinhoud
De verpakking bevat het volgende:
• Accu • Emulgeermes
• Afneembare mixstaaf met driehoekig
voorgemonteerd mes • Set voor het verwijderen van het mes
• Handleiding
BUFFALO is trots op de haar productkwaliteit en dienstverlening en controleert de inhoud van de
verpakkingen, tijdens de verpakkingsfase, op functionaliteit en schade.
Mocht uw product door transport beschadigd zijn, neem dan onmiddellijk contact op met uw BUFFALO-
dealer.
Bediening
Handgreep
Aan/UIT knop
Veiligheidsknop
Variabele snelheidsknop
Vergrendelknop
Afneembare mixstaaf
Beschermkap
Accu
FS440-FS441-FS442_ML_A5_v1_20211118.indb 10FS440-FS441-FS442_ML_A5_v1_20211118.indb 10 2021/11/18 16:322021/11/18 16:32