Buffalo AirStation Nfinity WZR-AGL300NH User manual

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
Hardware Setup of WZR-AGL300NH Router:
1. Power on Buffalo Router, and wait for 1 minutes. The “Power”, “n” and
“Router” indicators will be ON, and other indicators will be OFF.
2. At the back of router, set the switch “Router” to “ON”
3. To reset the router, please insert “R S T” hole by a paper clip for
about 10 seconds, and wait for 1 minutes. The “Power”, “n” and
“Router” indicators will be ON, and other indicators will be OFF.
4. Please power off modem for 1 minute. Then power on modem again.
5. Please connect your broadband service with a network cable (or from
modem) to the “Internet” port on the RO TER. Then use another
network cable to connect “LAN1” port on the RO TER to the Ethernet
adapter on your PC. Make sure indicators “Internet” and “LAN1” on
front panel are ON.
6. Wait for 1 minute.
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 1

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
Prepare for Buffalo Router installation (Windows XP)
Click “Start”
Click “Control Panel” or “Settings” -> “Control Panel”
Choose “Internet Options” or “Network and Internet Connections” ->
“Internet Options”
Click “Connections” tab, choose “Never dial a connection”, then click
“LAN Settings”nder “Local Area Network (LAN) Settings”, please UNCH CK all check
boxes, then click “OK” twice, and go back to Control Panel
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 2

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
nder Control Panel, please choose “Network Connections” or “Network
and Internet Connections” -> “Networks Connections”, then right-click
“Local Area Connection”, and choose “Properties”
Highlight “Internet Protocol (TCP/IP)”, and then click “Properties”. nder
“Internet Protocol (TCP/IP) Properties”, choose “Obtain an IP address
automatically” and “Obtain DNS server address automatically”, then click
“OK” twice and go back to Network Connections
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 3

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
Buffalo Router WZR-AGL300NH Internet Connection Settings:
1. Open Web Browser, under address bar, please type http://192.168.11.1,
and press “ nter”.
Login dialog box will be prompted.
Input: sername root, Password: no password by default
2. Click “Run the Internet Connection Wizard ( asy Setup)”
3. Router is now detecting Internet Connection.
4. After a few moment, the following page will be displayed and asking for
“Username/Password”.
Choose “When a setup other than PPPo is performed, Click Here”. For
some PPPoE user, this page may not be displayed, please choose “Manual
Setup” instead. Click “Next”
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 4

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
5. Choose “Set Router Mode ON”
4. Choose “PPPo Connection”
7. Please input the login username (e.g. [e-mail] or
[email protected]) and password (twice) of your broadband
service now. Then click “Next”
8. If “Check the Internet connection” process is successful, the
following page will be displayed. Click “Complete” to close the setup page.
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 5

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
9. If the login information is incorrect, the following page will be displayed.
Please confirm login information. Click “Back” button to return previous
page, re-enter login username/password (twice), and then click “Next” to
check internet connection again.
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 6

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
Buffalo Router WZR-AGL300NH Wireless Connection Settings:
Buffalo Router WZR2-G300N Wireless Connection Settings:
Launch Web Browser, enter http://192.168.11.1 in address bar and then press
nter. Then type username as “root”, default no password.
1. Click “Wireless Config”
2. nder page “WPS”, please UNCH CK “enable” option behind “WPS”
Click “Apply” to save settings
Wait for 1 minute.
After settings saved and return to previous page. Please click “Setup”
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 7

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
3. On “Setup” page, click “Wireless ncryption (W P/TKIP/A S)”
Click “11a and 11g will be the same encryption method”
Click “W P”
5. To secure your wireless network, you can setup W P wireless
encryption on this page.
- Set “W P ncryption Key” to ”Character Input: 13 characters
(W P128)”.
- Behind “1”, input a 13 characters wireless encryption key to secure the
wireless network.
- Click “Apply”button, and then click “Apply” to save settings.
Wait for 1 minute.
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 8

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
Click “Complete” and return to “Setup” page
5. On “Setup” page, click “Wireless SSID & Channel(11n300MHz
Mode) ”
nder “Wireless SSID and Wirless Channel Settings” page, the SSID
(wireless network signal name), and Wireless Channel can be changed.
The default SSID of router is “_A” and “_G” appended to “MAC Address”
of router.
nder “SSID”, input new wireless signal name on the field behind for
“802.11a” and “802.11g”. (Remark: Cannot exceed 32 characters, and
leaving blank in between is not recommended),
nder “802.11g” → “Wireless Channel”, please fix a wireless channel for
your router.( sing “Auto Channel” is not recommended). Please try channel
1, 6, 11, or other channels until the wireless network is stable.
Please click “Apply” and then “Apply” again to save settings.
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 9

WZR-AGL300NH Router Settings (For : Pccw, HGC PPPoE ser)
Wait for 1 minute.
Click "Settings Complete" and return to "Setup" Page.
<Setup Complete.>
Last pdate Apr 16, 2009 Hornington Knowledge Base http://kb.hornington.com WZR-AGL300NH PPPoE Page 10