Bullmer A200-2 User manual

Ink jet plotter
--Operating manual

Foreword
Thank you for choosing an inkjet plotter. Inkjet plotter using a
Hewlett-Packard CAD Special nozzle technology, with high speed and
precision, stable characteristics, up to 600DPI resolution;Inkjet plotter
supporting the "Drawing Management Center" software that can draw
HPGL format files from a variety of software, such as love
Lancaster.OPTITEX.Bo. Rick, etc., as for ink jet plotter output drawing
commands, "drawing management center" will all tasks related to
information accurate dynamic real-time displayed, advocating "" what
you see.
Before you use this inkjet plotter, please read the manual carefully, to
ensure that you can efficiently. Successfully complete the machine all
functions work operation, such as an unidentified place, please contact
our service provider, to seek further help.
(this manual are subject to change without prior notice)

Catalogue
Chapter one Safety Tips
Chapter II Use matters needing attention
2.1 the use of the machine environment
2.2 other considerations
Chapter III Brief introduction
3.1 the basic introduction
3.2 parts and their functions
Chapterfourth Installation
4.1 the installation of the machine
4.2 the connection
4.3 the paper
Chapter five Inkjet plotter Center Software Description

Chapter one Safety Tips
Please read carefully before using this ink jet plotter all of the following
guidelines:
*Ink jet plotter on level ground, to avoid unnecessary failure caused
by not smooth plane.
*Please use the rated voltage (220V), not to inkjet plotter is
connected to the accessory no rated voltage, power supply instability
will lead to performance degradation plotter, plotter or even destroy
the power board.
*Power plug should be plugged into the power strip with a ground
wire, such as the machine is not grounded, because static electricity
discharge caused by excessive accumulation of serious damage to the
plotter.
*Avoid inkjet plotter with maximum power of frequent startup device
connected to the same power outlet, such as air conditioning and
other equipment, if in parallel on the same power outlet, make sure
that these devices should not exceed the power required to power
socket can withstand current.

*Do not use damaged or worn on the power line.
* Don't put inside the liquid drip into the plotter, otherwise it will
cause the components from the damage of circuit board short circuit
of the machine.
*Don't try to lubricating the moving parts of the machine.
*Unless the machine instructions are on the "use manual", otherwise
please don't repair or remove the plotter.

Chapter II Use matters needing attention
Although you are very familiar with inkjet plotter, but before operating this
machine also please read the following precautions:
2.1 the use of the machine environment
Plotter work and storage temperature range is: 15 to 35 degrees Celsius,
not in the glare, radiation or heat storage or use of this machine.Plotter work at
room temperature humidity range is: 20% - 20%, do not use in wet or humid and
dusty places plotter, because once the moisture condensation inside the machine,
dust entering the plotter and cause short circuit or poor contact and seriously affect
the plotter to avoid performance in strong electromagnetic interference or put
something magnetic beside the plotter
2.2 other considerations
*Before access or disconnect the power supply, make sure the machine is in
the off state.
*Avoid unnecessary frequent on and off the machine, so as not to affect the
performance of electronic components.
*In the process of drawing, don't put the body near the plotter, don't put
your hands on track
*If need to access or adjust the transmission signal, please confirm the
power of the computer and plotter switches have been closed.

Chapter III Brief introduction
Inkjet plotter resolution up to 300-300, at the same time drawing speed per hour
up to 50-200 square meters, more than 20% higher than that of other inkjet plotter
per hour - 50% of the drawing production, and can accurately automatically judge
shows status information using HP original HP51645 nozzle, free maintenance,
high resolution, low use cost
3.1 the basic performance indicators
Model A200-2 A220-2 A240-2 A240-4
Maximum width on
paper
172cm 190cm 220cm 210cm
The biggest
drawing width
165cm 185cm 200cm 190cm
The average speed
of drawing
80 SQ
MTS/HR
80 SQ
MTS/HR
80SQ
MTS/HR
160SQ
MTS/HR
Resolution 300-600 DPI
The ink head type HP51645
Quantity of nozzles 2 2 2 4
Ink Type Add 2-8 times repeatable
The biggest paper
weight
100
KG
100 KG 100KG 100 KG
The type of paper 30g-300g
Port USB2.0
The drawing
language
HPGL
Power/voltage 220V AC
Frequency 50HZ-60HZ
Net weight 80K
G
100KG 100KG 135KG
Drive mode Intelligent servo

3.2 parts and their functions：
（1）control panel （2）The cartridge group （3）HP ink box
（4）pinch roller （5）Paper roll grinding wheel （6） Paper roll
（7） Began to collect paper sensor （8） Stop paper sensor
（9） Feed roller （10） protective cover （11） power switch
（12） The side panel （13） The beam （14） Pressure paper rod
（15） The base

Chapterfourth Installation
4.1 the installation of the machine
4.4.1 check the goods before installation
This machine consists of the following items: host, support group (including
the left and right sides, around the base, beam), the power cord, USB cable, HP
cartridges, paper feeding roller, the pressure rod, screw, hex socket wrench.
Please refer to the following assembly drawing installation:

4.1.2 installation host and support
With reference to the above group around the beam with socket head cap
screw and bracket connected, and then the host on the bracket, at the same time
take the host and the bracket in inner hexagon spanner, again according to the logo
connecting line the good joint.
4.2 the connection
4.2.1 Please make sure the machine power switch is closed, and ensure the
power supply voltage of 110-220 - v, connect the power supply..
4.2.2 Connect the USB interface to PC, read in inkjet plotter center software,
installed driver, prepare the way for drawing.
4.3 Paper was
After installation of the machine, our paper work can be carried out, in paper
cones fixed drum paper (note that the direction of the paper, the pressure lever on
the paper after paper rod guide groove, the paper from to the pressure after the
paper rod under beam, then move up to the machine after the above, through the
pressure roller, to accept the location of the drum of paper, take up the paper, and
then use tape from the middle to put the paper on the paper roller with both sides,
laying a good pressure bar paper paper; Open the check, press down the button on
the control panel, can guarantee to deliver the paper stem paper paper down rod, at
the same time will pressure paper rod into paper rod guide groove pin.

Chapter five Instructions on the use of the ink jet
plotter center software
Inkjet plotter drawing center software, can draw from a variety of
software *. PLT file, such as love, OPTITEX. G. Rick, etc., and can
accurately and automatically judgment and display will be drawing time;
Has the intelligence and automation of the ink head cleaning technology.
About the software instructions please read the following instructions：
1、Open the software will appear below the main interface, menu bar,
toolbar, workspace, the status bar (figure 1)。
（figure 1）

2、 Language function switch: the software supports. The English
version, in the language selection in the parameter Settings are free
to switch(figure 2)。
（figure 2）
3、File to import, click the file to import files or toolbar (figure 3), choose to
print *. Pit file, click ok (figure 4. Figure 5), will see in print control directory will
print file for detailed information, and tool column of file processing tools, such as
start print. Print pause. Image zoom in and out. Print in advance and buy later, etc.

(figure 3）
（figure 4）

（figure 5）
4、 Parameter Settings: the directory in the preferences in the
menu bar user preferences in parameter Settings. The system parameter
Settings, and other three options, according to the file will print to
parameter setting, can print documents（figure 6、7、8、9）。
（figure 6）（figure 7）

（figure 8）（figure 9）
5、 After drawing: click to choose the file to print, click
start printing and sure, plotter will draw this file, and in
the process of drawing the workspace and the status bar will
clearly reflect the process of drawing(figure 10.figure 11)。
（figure 10）

（figure 11）