BUTURE Beta03 User manual
BUTURE
QUICK-START
GUIDE
JUMP
START
YOUR
CAR
©
Insert
the
jumper
cable
into
the
jump
starter
(220%
power).
@
Connect
the
clamps
to
car
battery
(red
to-+,
black
to
-)
©
start
your
car
engine.
+
ABOUT
THE
FORCE
START
FUNCTION
If
three
attempts
fail
when
you
correctly
connected
the
clamps
to
your
car,
you
can
use the
Force
Start
Function
to
enter
boost
mode.
G
©
Check
the
clamps
connection
and
the
product’s
battery
is
above
20%.
3
steps
to
fix
the
problem:
@
Press
the
Force
Start
Button
for
3
seconds.
©
The
indicator
will
be
green,
and
go
back
to
start
engine
ignition.
Caution:
When
using
this
function,
auto-detection
and
safety
features
will
be
disabled
temporarily.
+
ABOUT
THE
TROUBLESHOOTING
In
any
of
the
following
situations,
the
smart
clamp
will
turn
protections
on:
Indicator
Situations
Flashing
red
and
green
|
Standby
status
solid
green
Ready
to start
1.
Low
voltage
protection
-Recharge
the
product
2.Over-heating
protection
-Remove
the
clamps
to
let
it
cool
3
Timeout
protection
~Connection
timed
out.
Start
engine
within
605
or
remove
the
clip
within
30s
after
a
successful
start
Solid
red
1.Reverse
polarity
protection
-Reverse
the
clips
and
ensure
the
correct
Solid
red
with
connection
discontinuous
beep
2.
Sticking
fault
-Contact
for
replacement
parts
Short-circuit
protection
-Don't
connect
the
clips
together
or to
the
same
metal
Solid
red
with
long
beep
Please
contact
with
omer
detalls
CHARGE
OTHER
DEVIDES
©
Plug
the
cable
into
any
USB
outport.
=T
U
@
Press
the
power
button.
LED
LIGHTING
Press
the
switch
e
press
shortly
press
shortly
press
shortly
lighting
strabe
IMPORTANT
SAFETY
WARNING
1.
Store
in a
cool
and
well-ventilated
place
out
reach
of
children
and
pets.
2.Do
not
place
the
product
in
high
temperature
environment
for
a
long
time.
The
operation
temperature
of
this
product
is
-20-60°C.
The
storage
temperature
should
not
exceed
50°C/122°F.
3.0nly
start
vehicles
with the
smart
jumper
cable
supplied
by
the
manufacturer.
4.Do
not use the
product
if
the
clamp
or
cable
is
damaged.
5.Do
not
connect
the
red
and
black
clamps
together
when
the
product
is
outputting.
6.
Do
not
connect
the
red
and
black
clamps
to
the
same
piece
of
metal.
7.
Do
not
disassemble
or
modify
this
product.
8.
Do
not use
detergent
to
clean
this
product.
9.
Do
not
abuse
this
product
and
avoid
heavy
dropping
or
repeatedly
hitting
it.
10.
Do
not
operate
the
product
in
explosive
environments
such
as
flammable
liquids,
gases
or
dusts.
11.
Do
not
immerse
the
product
in
water.
12.
Do
not
litter
the
product
and
it
should
be
safely
recycled.
13.
Do
not
incinerate
the
product
or
exposed
to
high
temperatures,
as
they
may
explode.
14.
Only
use
replacement
parts
or
accessories
provided
or
recommended
by
manufacturer.
Table of contents
Other BUTURE Remote Starter manuals
