bvk otcaccess C5 User manual

NCR 6632 1
C5
by
Installation manual

NCR 6632 2
Content
Considerations before installing C5 ........................................................................................................................................ 3
List of conditions where C5 should not be installed: .............................................................................................................. 3
What is C5 ............................................................................................................................................................................... 3
FCC Compliance Information .................................................................................................................................................. 4
C5 ports ................................................................................................................................................................................... 5
Preparing the Beauty Door ..................................................................................................................................................... 6
Preparing the safe door .......................................................................................................................................................... 9
Removal of the existing safe lock ............................................................................................................................................ 9
Keypad installation ................................................................................................................................................................ 12
New lock installation ............................................................................................................................................................. 13
Installation of C5 ................................................................................................................................................................... 14
Top box lock installation ....................................................................................................................................................... 15
Top box cables ...................................................................................................................................................................... 17
ATM Safe box preparation .................................................................................................................................................... 20

NCR 6632 3
Considerations before installing C5
Before installing C5 to an ATM, visually inspect the ATM to detect any abnormalities that could negatively affect the
regular functionality of C5.
In case you face any of the problems listed below quit the installation.
List of conditions where C5 should not be installed:
 Evidence of vandalism (broken bezel, open or broken fascia, unscrewed side panels, broken screws, damaged
dispenser etc.)
 Problems in the opening space of the ATM
 If there is another operator working on the ATM.
 If the area doesn’t meet minimum security requirements (remote location, insufficient staff surveillance)
 If there is any problem caused by a natural phenomenon (flood, energy cut, air conditioning failure etc.)
What is C5
C5 is a control unit. It gives the possible to drive and monitor the locks and door switches connected to it. Thanks to C5,
the access to the ATM will be executed with OTCs (One time codes). Physical keys will not be longer needed.
The C5 is accompanied by a physical or digital keypad used to enter the One Time Codes. The electric or data driven
locks connected to the C5 will be triggered when a valid OTC is entered to keypad.
The MiniSmart Keypad and the locks can be set up and powered with OTCaccess controllers only.
The MiniSmart Keypad power sources shall be 12 Vdc SELV with LPS or PS2.

NCR 6632 4
FCC Compliance Information
OTCaccess C5 controller with FCC ID: 2A4FC2105
OTCaccess MiniSmart Bluetooth Keypad with FCC ID: 2A4FC2303
The devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) the
devices may not cause harmful interference, and (2) the devices must accept any interference received,
including interference that may cause undesired operation.
Note: The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If the equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this product not authorized by BVK Technology could void the electromagnetic
compatibility (EMC) and wireless compliance and negate your authority to operate the product.

NCR 6632 5
1
2
3
4
5
6
7
Bottom
C5 ports
1.
Power
2.
USB Type B
3.
Analog
Keypad
4.
Keypad
5.
Motor 1
6.
Door Switch
7.
Digital Output
8.
Door switch
9.
Motor 2
10.
Motor 3
11.
RS 232
12.
RS485
13.
RJ45 Ethernet
8 9 10 11 12 13
Top

NCR 6632 6
Preparing the Beauty Door
1.
Remove the outer door
2.
Bent the protruding parts with pliers so that the surface is plain

NCR 6632 7
3.
Put the hole template on the upper left
corner of the door. Mark locations
4.
With a drill bit, drill 4mm holes on edges
and 20 mm hole in the middle
5.
Clean the holes from inside
6.
Prepare the lock with the plastic handle

NCR 6632 8
7.
Unscrew the lock
8.
Fit the lock fixing plate on the front.
Secure the plate with M4 nuts from the
back. Insert the lock
9.
Fix the lock in place with its nut from the
back
10.
Place the hook of the lock as shown in
the Picture and fix it with its screw

NCR 6632 9
Preparing the safe door
1.
Unscrew the 2 metal pieces from the
steel door of the safe
2.
Install the new striker pieces instead. Fix
them with two M4x10 RYSB bolts
Removal of the existing safe lock
1.
Open the safe door. Unscrew the inner guard
metal plate
2.
If the metal plate is closed, unlock it with the
key

NCR 6632 10
3.
Remove the metal
plate
4.
Unscrew the screws of the lock
5.
After removing the cover, unscrew the
existing lock.
6.
Remove the lock