BWS AENEEMA 2016 User manual

STYLE. PERFORMANCE. SIMPLICITY.
AENEEMA KITE MANUAL 2016

SURF-SPECIFIC
SIMPLICITY
All our products are designed for wave
riding.That means they are construct-
ed to withstand rough treatment and
designed to be clean, functional & stay
out of your way.

Warning !
Kite flying can be
dangerous!
Always use extreme
caution when using this
product.
Misuse of this product can cause
serious injury or death. Only use
this product if you are in good
physical health.
Never act in a careless manner
when using this product (such
as jumping in the air, or tying
yourself down).
You are responsible for your
own safety, and the safety of
others around you when using
this product.
Important Safety Rules
This product is not a personal
otation device. Always wear a
Coast Guard approved personal
otation device when using this
product near the water.
Always have a partner to assist
with launching and landing your
kite.
Always learn to use a small
two-line trainer kite before
attempting to use this product.
Never allow anyone who is not
familiar with traction kiting
to use this product without
experienced assistance.
Never use this product without
a leash system. A loose kite
is extremely dangerous to
everyone down wind.
• The leash system is not a
permanent attachment to this
product. Never permanently
attach yourself to the kite or
any of its components.

Warning !
Kite flying can be
dangerous!
We recommend you wear a
helmet, gloves, shoes, and
protective eyewear when using
this product. Always use a high
quality, kite specic harness.
Before using this product
take lessons from a reputable
school. Do not attempt to y a
kite without being trained by a
kite instructor.
Practice and master the
operation of your safety quick
release device in light wind- non
emergency situations, so you
are condent in it’s use in the
chance of an emergency.
Rinse your Quick Release
device in fresh water after
every session. Quick Release
devices have a limited lifetime
and must be checked and
changed often.
Always check your lines and
ropes for sign of wear and
replace them when they show
signs of weakness. Normal
wear and tear on ropes is not
considered a warranty issue.
Always secure kite to ground
with sand or sandbags when
not in use.

Warning !
Kite flying can be
dangerous!
Choose Safe Weather Conditions
• Never learn to use this product in more than 10 knots of wind.
• Never use this product in high winds.
• Never use this product in thunderstorm and lightning
conditions.
• Only use this product when you can remain in a standing
position.
• Never use this product in wind conditions that are above your
ability level.
• Never use this product near or on the water in oshore wind
conditions unless you are an expert swimmer.

t
Choose a Safe Location
Always observe local rules and regulations when using this product.
• Never use this product near power lines, telephone poles, trees, bushes, roads, automobiles, or
airports.
• Only use this product when you have 100 meters of clear space downwind, and on both sides
of your launching position. The power of the kite can pull you downwind unexpectedly and with
great force.
• Do not y your kite over other people or pets. Spectators should remain upwind of you when
using this product.
• Never use this product on crowded beaches or elds.
• Never use this product near the water unless you know how to swim and are in good physical
health.
• Practice launching and landing procedures, and self rescue techniques before using this product
near the water.

ASUMPTION OF RISK:
Use of the Benwilsonsurf Product
and any of its components involve
certain inherent risks, dangers, and
hazards that can result in serious
personal injury and death to both
the user and to nonuser third
parties. In using the Benwilsonsurf
Product, you freely agree to assume
and accept any and all known and
unknown risks of injury to you and
to third parties while using this
equipment. The risks inherent in
this sport can be greatly reduced by
abiding by the warning guidelines
listed in this owner manual and by
using common sense.
By assembling and/or using this product, you agree that
you have read and understood the entire product owner’s
manual, including all instructions and warnings contained
in that manual, prior to using the Benwilsonsurfproduct
in any way. You additionally agree that you will ensure
any additional or subsequent user of your Benwilsonsurf
product will read and understand the entire product
Owner’s Manual, including all instructions and warnings
contained in that manual, prior to allowing that person to
use your Benwilsonsurfproduct.
If you do not agree to be bound by these conditions then
return this product ( unused) for a full refund.
RELEASE OF
LIABILITY, CLAIM
WAIVER,
ASUMPTION OF
RISK

including negligence or breach
of contract on the part of
Benwilsonsurfandallrelatedparties
in the design or manufacture of the
Benwilsonsurf product and any of
its components. In the event of your
death or incapacity, all provisions
contained herein shall be eective
and binding upon your heirs, next
of kin, executors, administrators,
assigns, and representatives.
Benwilsonsurf related parties have
not made and expressly deny any
oral or written representations
other than what is set forth herein
and the Benwilsonsurf product
User’s Manual.
In consideration of the sale of the Benwilsonsurf product
to you, you hereby agree to the fullest extent permitted by
law, as follows:
To waive any and all claims, that you have or may in the
future have against Benwilsonsurf and all related parties
resulting from use of the Benwilsonsurf product and any
of its components.
To release Benwilsonsurf and all related parties from any
and all liability for any loss, damage, injury or expense that
you or any users of your Benwilsonsurf product may suer,
or that your next of kin may suer, as a result of the use of
the Benwilsonsurf product, due to any cause whatsoever,
RELEASE OF
LIABILITY, CLAIM
WAIVER,
ASUMPTION OF
RISK Cont...

Blue Lagoon
Green Machine
Hot Orange
Yellow Gold
Sizes: 5.5/7/8/9/11/13
Surf Bridle System:
Made possible by industry-rst software, Dano See has developed a new Surf Bridle
System. This system’s compact 4-point conguration incorporates a new generation
of weight distribution technology that allows us to individually weight each string and
provide 100% even distribution of pressure. This ensures your canopy remains tight and
taut throughout all phases of sheeting with zero distortion and drag. Aeneema is direct,
responsive and easy handling without the use of bungees, pulleys or bridle bandaids
others claim work better. Style, performance, simplicity.

The Hybrid ‘Glyde’ Clean Canopy Design:
The Aeneema’s super thin proles and lightweight hybrid Clean Canopy Design
allows for faster air speed ow, smoother ying sharp, resposive turning radius in
all conditions. The Glyde technology emerges from the super clean canopy design
so the kite is always ying and gliding through any lull or dead spot. Medium
thickness struts and a reduced diameter LE accommodate the rigid frame for a
seamless clean canopy shape, no uttering or stretch wrinkles that cause drag.
at the edge of the window.
EPI - Express Point Inate:
Introducing the all new Black Betty 2-in-
1 EPI valve. Interlinking hoses connect
all struts to the LE for express all-in-one
ination. Plus we include an extra large
threaded output for ultra-fast deating.
1 Piece Bladder:
Less welds = less chance of blowing out
a seam.
Features of the AEneema Kite
Board-Spectrum Performance &
Surf-Specic Simplicity
Faster Turning & Unbeatable
High-End Stability
Ultimate Drift & Consistent Drive
Smooth ON/OFF Power

THE
Æneema
The Ultimate Wave Kite
2. Hard-Wearing Canopy
3. Struts (x3)
4. Bridle
1. Leading Edge (LE)
Basic Kite Anatomy
5. Consistent Drive Wingtip:
All BWS kites incorporate our Consistent
Drive wingtip design that allows crisp
owing turns and NO stalling or dead spots
in any area of the window.
6. Express Point Inate (EPI)

INFLATING
YOUR KITE
1. Lay the kite out on the sand, grass or a surface
free of hard or sharp objects as they could
damage it.
2. Turn the kite canopy facing down with the Leading Edge pointing into
the wind.
3. Tether the kite to your pump using the attachment to prevent it blowing
away.
4. Ensure all connecting valves are joined and free from sand/dirt.
5. Attach the pump to the inate valve, ensuring the dump valve is closed.
6. Inate kite till rm and taught to the touch.
7. Detach the pump nozzle and quickly close the inate valve.
Kite on ground., canopy
down with Leading Edge fac-
ing into the wind.
Close-up view showing
inflate/deflate valves. At-
tach pump to ‘EPI’ valve and
inflate till taught to touch.

ATTACHING
YOUR LINES
8. Unroll your lines o your bar making sure there are no
twists
9. Make sure the bridle of the kite is not tangled. Place
your kite on its leading edge and connect the center lines
to the front bridle attachment points.
10. Connect the red and black outside lines to the rear
attachment points. Make sure the red y line is connected
to the red attachment point and the black y line is
connected to the black attachment point.
11. Connect safety leash from your harness to the o
switch ring. Ensure the safety quick release is positioned
close to your harness.
**Safety Leash
If you need to activate the quick release on the
safety leash simply grab the tubing section and
pull in the direction of the arrow.
Make sure the release handle is within reach
when attaching it to your harness. We do not
recommend hooking the leash to your back.
Safety Leash Reset
• Insert the metal safety pin through the loop
in the rope end.
• Fold the stainless steel ring over the loop and
secure the end by pulling the plastic tubing of
the red safety handle over the QR pin until it
rests securely against the plastic ball.
• Double check that your Safety leash is seated
properly by pulling to the outside of the red
handle on both sides.
Attach lines as shown.
Red - rear (outer)
Black - front (centre)
Connect safety
leash to o-
switch ring
and harness as
shown.
9. Connect the
lines as shown.

CARING FOR
YOUR KITE
- Avoid bringing the kite into contact with sharp-edged rocks, thorns,
wood and other objects that may damage, puncture or tear the cloth.
- Do not expose the kite to excessive sun as it ages the material unnecessarily.
- Deate the bladders if the kite is to be left unattended for any length of time.
- Avoid leaving your kite on the beach for extended lengths of time as small
wind movements may quickly cause wear and tear to the cloth.
- Try to pack up the kite without cuttlings into the kitebag to avoid tearing the canopy.
- To carry a kite, turn it so that the leading edge is upwind and the underside faces
upward. Grab the center of the leading edge tube. If the wind is blowing, it will
hold the kite clear of the ground. Be sure not to drag the tips of the kite across the
ground.
- A coating that results from using the kite in salt water will not damage the kite.
However, rinsing in fresh water and drying doesn’t hurt.
- When cleaning the kite be sure that no water, dirt, or sand gets inside the bladders.
- Be sure that the kite has dried completely before packing it up.
Otherwise changes of color or mildew could occur.
Such bleeding Is not covered under the BWS warranty scheme
- Do not dry the kite in direct sun!
FOR MORE INSTRUCTIONAL
TIPS, HOW-TO CLIPS AND
MAINTENANCE VIDEOS,VIS-
IT OUR YOUTUBE CHANNEL.

At BWS, the customer always comes rst. If you’re unhappy with a BWS kite or board, it’s our duty to keep you
stoked on the brand. However some situations, particularly those caused by wear and tear, are not a warranty
issue and should be dealt with by a repairer. We have a two-phase policy consisting of our “Out Of The Box” and
“Fair Deal Policy” in place to manage these warranty issues.
Out of the box warranty:
We guarantee our products are free from defects in materials and workmanship.
Kites - material has no aws and the stitching is sound
Boards - board is well-constructed and free from defects
All our products are inspected before they’re packed and sent. Kites are inated, photographed and recorded
to ensure you receive quality equipment. If you are not satised with it when you unpack it, then just contact us
as soon as possible and we’ll take action.
BWS WARRANTY

ISSUES NOT COVERED BY WARRANTY
Normal wear and tear is not covered:All gear does wear with use so if you kite a lot and your gear wears out we
consider that normal. Lines and depower ropes wear with time and need to be maintained and replaced. If you
damage your kite as a result of a wipeout then that is not classied as a warranty issue.
Abuse and accidents:If you damage your kite in a crash we would class that as an accident or abuse.
Abuse and accidents:If you damage your kite in a crash we would class that as an accident or abuse.
Surf:Whilst we build the strongest and lightest kite we can, we will not cover anything damaged by wave
action. It’s impossible to build a bombproof kite.
Environmental damage:If you leave your kite in the heat or sun and it fades, discolours or pops a bladder due to
excessive heat then this is excluded. Likewise, boards delaminated in the sun or hot cars are excluded.
Modications:If you modify your kite or board from its original state then we won’t cover it. Camera attachments
and repairs are not supported.
Boards:We build our boards to last as long as possible and also to be light and functional but they are not
indestructible. They’re designed to surf on not boost massive airs. We don’t guarantee the boards from breakages
due to massive jumps or waves action. Snapped ns or ripped out n boxes caused by hits on reef, sandbank or
beach are not covered. Boards should not be left in direct sunlight for extended periods or left in cars on hot
days. Excessive heat can cause delamination or discoloration and will not be covered under warranty.
The above list is not exhaustive of what we think is a Fair Deal. If you think you have a legitimate request then
let us know and we’ll assess it. Remember we have been Surng & Surf Kiting since the beginning and have seen
just about every case of product failure.
BWS WARRANTY

Fair deal warranty:
We all use and treat our gear dierently, a factor considered in our fair deal warranty. This means if you kite
every day and are hard on equipment then we’ll warranty it for a shorter time.
However, if you only kite once a month then we’ll guarantee your gear for a longer period - up to a maximum
of 12 months from date of purchase. We assess each kite or board on a case-by-case situation - if we think it’s a
fair deal to replace or repair the item, we’ll do it.
The Fair Deal Warranty works both ways. There are some situations we believe don’t constitute a claim. The
following is an outline of these situations.
BWS WARRANTY

Damages during shipping:
BWS does everything possible to ensure the safe delivery of your new gear. It is unlikely that your items will be
damaged during shipping, but it can happen from time to time.
In the unlikely instance of damage occurring during shipping, it is the customer’s responsibility to notify the
shipper and BWS immediately. If you notice any outside damage to a box, we recommend photographing and
inspecting the contents immediately to ensure they have arrived undamaged and that no items are missing.
You should ask the driver to document that the box arrived damaged. Often the shipper will want to inspect
the box and packaging materials, so be sure to retain everything until instructed otherwise by the shipper. You’ll
need to take photos of the damaged packaging as well as damage to the item.
If the damaged item is found after the driver has left your premises, contact the shipper at once by calling their
local oce.
TO MAKE A CLAIM
If you think you have a warranty claim then email us. We’ll forward you a simple assessment process, which
will involve taking a few photos of your item and providing us with some info. Warranties are only valid to the
original purchaser. You must register your products Online to be eligible for our Fair Trade Warranty system.
BWS WARRANTY

we live and breathe the ocean and there is nothing more rewarding than
connecting with like-minded people. For us it’s just as exciting getting someone
new into kiting or helping crew take their riding to the next level as it is being
out on the water ourselves.”
~ Ben Wilson and Dano See
“We are all about the lifestyle,

KITE WEEKS
“One of my biggest passions in life is bringing
together people for the ultimate surf/kite travel and
coaching experience. We all share the same
conviction for the ocean and outdoors lifestyle.”
~ Ben Wilson
benwilsoncoaching.com/trips
VIRTUAL COACHING
Upgrade your skills with a membership Ben’s online tutorials.
benwilsoncoaching.com
CONNECT
Connect with us so we can all share photos
and vision of everything we love with our
amazing worldwide network.
IG: @bwsurf_australia
twitter: @bwsurf
Facebook: BWSurf
VIDEOS
BWS are the industry leaders in lms, short
movies and how-to clips so please check out
our inspiring vision.
bwsurf.com/connect/movies
bwsurf.com/connect/how-to-kite-videos