Cadac Safari Chef 2 User manual

503-0453 LEV26
USER INSTRUCTIONS
NOTE! PRODUCT MAY VARY FROM ILLUSTRATIONS
MODEL No: 6540L0 & 6540L1
28mbar & 50mbar
LIVE THE BRAAI LIFE
SAFARI CHEF
MODEL No: 6540L1
MODEL No: 6540L0
GB DE DK ES FR IT NL NO PL SE SI FI

11
CAUTION
For Outdoor use only!
This appliance may not be used in an exterior enclosed balcony, porch or entertainment area!
IMPORTANT
Read these instructions for use carefully so as to familiarize yourself with the appliance before connecting it to
its gas container. Keep these instructions for future reference.
GB
1. General information
• This appliance has been designed to be used for outdoor cooking, specically for people who go camping to enjoy outdoor life and it
can also be used at home on your patio.
• Various food types can be prepared on this appliance. The Safari Chef 2 is designed to utilise various cooking surfaces.
• Gas is supplied to the unit via a hose and regulator, connected to a gas cylinder or a CADAC Power Pak. The CADAC Power Pak is a
unit that takes two or more gas cartridges. Note: hose, regulator and Power Pak are not supplied with the appliance.
• The unit is easy to switch on, and to operate (Section 6) and the user can control the heat input with an adjustable valve.
• The unit is supplied with a convenient carry bag.
• This appliance complies with EN 498:2012, EN 484:2019 and SANS 1539:2017.
• This appliance may only be used with an approved hose and regulator connected to a rellable cylinder complying with the local
regulation in force.
• The rellable cylinder is to be used
only in an upright position. Only to be
used with a gas cylinder that does not
exceed 500mm in height and 350mm
in width (including the regulator).
• Warning: Accessible parts may be very
hot. Keep young children away.
• Gas appliances require ventilation for
efcient performance and to ensure
the safety of users and other persons in
close proximity, therefor do not use the
appliance in an unventilated area. It is
intended for use outdoors only.
• Read these instructions carefully before
using the appliance.
• Use outdoors only!
6540L0, 6540L1
Country of Use BE, CH, CY, CZ, ES, FR, GB, GR, IE, IT, LT,
LU, LV, PT, SK & SI PL
BE, CY, DK, EE,
FR, FI, HU, IT,
LT, NL, NO, SE,
SI, SK, RO, HR,
TR, BG, IS,LU,
MT, & ZA
AT, CH, DE
& SK
Appliance Categories I3+(28-30/37) I3B/P (37) I3B/P (30) I3B/P (50)
Allowable gasses Butane Propane Butane, Propane or their mixture
Gas Pressure 28-30mBar 37mBar 37mBar
28-30mBar
(2.8kPa for South
Africa)
50mBar
Jet Number 0.65 0.59 0.65 0.56
Nominal Usage 130g/hr 130 g/hr 130g/hr 130 g/hr
Gross nom. heat input 1.8kW 1.8 kW 1.8kW 1.8 kW
Country Name and Abbreviations
AE = United Arab Emirates AL = Albania AT = Austria BE = Belgium CH = Switzerland
CZ = Czech Republic DE = Germany DK = Denmark ES = Spain FI = Finland
FR = France GB = United Kingdom GR = Greece HR = Croatia IT = Italy
JP = Japan KR = Korea NL = Netherlands NO = Norway PL = Poland
PT = Portugal RO = Romania RU = Russia RS = Serbia SI = Slovenia
SK = Slovakia SE = Sweden TR = Turkey ZA = South Africa
2. Safety Information
• Do not move the appliance during use.
• Turn off the gas supply at the gas cylinder after use.
• The hose must be checked for wear or damage before every use and before connecting to the gas container.
• Do not use the appliance if it has a damaged or worn hose. Replace it.
• Do not use an appliance that is leaking, damaged or which does not operate properly.
• This appliance must be kept away from ammable materials during use. Minimum safe distances are: Above the appliance 1.2m. At the
rear and sides 600mm.
• Ensure that the gas container is tted or changed outdoors, away from any sources of ignition, such as naked ames, pilots, electric res
and away from other people.
• Keep gas containers away from heat and ame. Do not place on a stove or any other hot surface.
• Ensure that the assembled product is stable and does not rock.
• In the event of light back (where the ame burns back and ignites at the jet), immediately turn off the gas supply by closing the control
valve on the gas container and then the appliance valve. After the ame is extinguished remove the regulator and check the condition of its
seal. Replace the seal, if in doubt. Re-light the appliance as described in section 6 below. Should the ame persistently light back, return
the product to your authorised CADAC repair agent.

2
• If there is a leak on your appliance (smell of gas), close the cylinder valve immediately and take
it into a ame free location where the leak may be detected and stopped. If you wish to check for
leaks on your appliance, do it outside. Do not try to detect leaks using a ame; use soapy water.
• The correct way is to smear the joints e.g. where the stem ts into the cylinder, with soapy water.
• If bubbles form, then there is a gas leak. Immediately turn off the gas supply by closing the
control valve on the gas container and then the appliance valve. Check that all the connections
are properly tted. Re-check with soapy water.
• If a gas leak persists, return the product to your CADAC dealer for inspection / repair.
• Use Outdoors Only.
3. Assembly Instructions
• WARNING: The legs are spring loaded. Opening and closing of the legs must
be done in a controlled manner to avoid personal injury or damage to your
Safari Chef 2.
• To open the legs, turn the unit upside-down and hold the legs down while lifting each leg
individually (Fig. 4c). You will hear a “click“ if the leg(s) has located correctly (Fig. 4a).
• To fold the legs back, securely hold the leg and push the leg release clip down (Fig. 4b). Then
push the legs in-ward to its closed position (Fig. 4c). This needs to be done sequentially to
optimize space. First the right front leg (1), then the left front leg (2), and lastly the rear leg (3)
(as seen in Fig. 4d).
• Before connecting the gas supply, rstly check that the appliance valve is in the off position by
turning the control knob fully clockwise (See Fig. 2).
• I 3B/P (30), I 3+ (28-30/37) and I 3B/P (37) Appliance categories: Fit the Valve Tailpiece onto
the Valve (Fig.5) by screwing it on in an anti-clockwise direction. Push an 8mm inside diameter
Hose onto the Valve Tailpiece until it is properly seated. On the other end attach a suitable
30mbar low-pressure (I 3B/P (30) and I 3+ (28-30/37) Butane congurations) or 37mBar low-
pressure regulator (I 3+ (28-30/37) Propane conguration), again making sure that the hose is
well seated. The hose used must comply with BS 3212 / SABS 1156-2 or equivalent.
• I 3B/P (50) Appliance category: Screw a Hose with the correct threaded ttings on each end,
onto the left hand ¼“BSP thread of the Valve. Attach a suitable 50mbar low-pressure regulator
on the other end of the hose. The hose used must comply with DIN 4815 part 2 or equivalent.
• Note: The hose and regulator are not supplied with the appliance. For details, contact your local
stockist.
• The hose length should be no less than 800 mm and shall not exceed 1.5 m. Check the expiry
date on the hose and replace when necessary or when national conditions require it. Do not twist
or pinch hose.
• Your appliance is now ready for use.
Fig. 3
Fig. 2
OFF
Fig. 5
28-30 & 37mbar
ONLY
GB
Fig. 1
Fig. 4c Fig. 4d
Fig. 4a Fig. 4b

33
GB
4. Component List
A B C D E F G H I J
6540L0-10
6540L1-10
6540L1-20
6540L1-21
6540L1-25
******
*****
***
**
***
**
***** * **
*
*
*
*
*
Quick Release (H)
Lid (A)
Pot/Dome (B)
BBQ Grid (C)
Flat Pan (D)
BBQ 2 Plancha (E)
Pot Stand (F)
(Max Pot Size: 300mm)
(Min Pot Size: 150mm)
Fat Pan (G)
Piezo Igniter (I)
Pizza Stone
(Optional Accessory)
Paella Pan 28
(Optional Accessory)
Carry Bag (J)

4
5. Fitting and Changing the Hose and Gas Cylinder
• Before tting the regulator to a gas container, ensure that the seal on the regulator is in position and in good condition.
This should be done on every connection.
• Ensure that the gas container is tted or changed outdoors, away from any source of ignition, such as naked ames or electric res and
away from other people.
• Making sure that the gas container is kept upright, screw the regulator onto the gas container until it is fully engaged. Do not over tighten.
• If there is a leak on your appliance (smell of gas), take immediately into a ame-free location where the leak may be detected and
stopped.
If you wish to check for leaks on your appliance, do it outside using soapy water only, which is applied to the joints. A formation of
bubbles
will indicate a gas leak.
• Check that all the connections are securely tted and re-check with soapy water. If you cannot rectify the gas leak, do not use the
appliance. Contact your local CADAC stockist for assistance.
• When changing a gas container close the cylinder valve and then the appliance Valve (see Figs. 1 and 2). Making sure the ame is
extinguished, unscrew the regulator. Re-t a full gas container following the same precautions as described above.
6. Using the Appliance
• This appliance must be used outdoors only!
• When in use, protect from wind for optimum performance.
• Do not move the unit whilst hot. The use of protective gloves is
recommended.
• CAUTION: Accessible parts may become very hot. Keep young
children away from the appliance.
• To pack away, let the unit cool. After cleaning, fold the legs of the
appliance as described is section 3 above. Place the pot / dome at
the bottom of the bag. Next, place the pot stand upside down into
the pot / dome. Place the fat pan upside down over the pot and pot
stand. Then place the appliance upside down onto the fat pan. Place
the grid and at pan into their separate holders located in the lid of
the bag and zip them closed. Fold over the lid of the bag, and zip it
closed. (Fig. 8)
• Keep the appliance in its Carry Bag when not in use, as this will
prevent the ingress of dirt or insects which may affect the gas ow.
• When attempting to light the appliance, make sure that the gas
supply from the cylinder is open prior to turning on the gas supply to
the appliance.
• Using the control knob
The control knob is tted with two positive stop positions, one at
low, and one at Ignite / High. This limits the adjustment of the
ame to between these two points.
Lighting up using the Piezo Igniter
• To light up the appliance using the piezo igniter, push in and turn the control knob in an anti-clockwise direction until you hear a
click. If the gas does not ignite on the rst spark, push in, and turn the control knob fully clockwise. Try again, by pushing in and
turning the control knob anti-clockwise until you hear a click.
7. Cooking Options
• There are ve available cooking options (the 5th is an optional accessory) with your Safari Chef 2 appliance. These are:
Barbecuing: This cooking option is ideal for fat-free barbecuing of chicken, sausages, chops, kebabs, sh or vegetables.
For this type of cooking, place the Fat Pan onto the heat shield. Place the BBQ Grid onto the locators of the Fat Pan.
Fig. 8
If the gas has not ignited in the rst two to three seconds you should close the control valve by pushing in the control knob, and
turning it fully clockwise. Wait approximately thirty seconds to let any accumulated gas within the burner pan assembly escape.
Repeat the above process if necessary until the ame ignites. The ame should normally light up within the rst one or two seconds.
Lighting up using a BBQ lighter
• When starting cold, the appliance may be lit from the top prior to tting the desired cooking surface onto the fat pan. When lighting up
a hot appliance however, it is recommended that this be done by sticking barbecue lighter through one of the Vent Holes underneath
the Burner, until it is in line with the burner (DO NOT place the BBQ lighter through the large hole directly underneath the burner).
Ignite the BBQ lighter. Whilst the BBQ lighter is lit, push in and turn the control knob anti-clockwise to light the burner.
• Use the control knob to adjust the ame intensity to the desired level by turning the knob clockwise to decrease the ame and anti-
clockwise to increase the ame.
• When not in use disconnect the appliance from the gas supply.
• WARNING: Do not use any cooking surfaces on a high ame setting for more than 10 minutes as this can damage the non-stick
coatings.
GB

55
GB
Caution: Please note that when cooking fatty meats some fat
will drip onto the unit which may cause are-ups. Please use
caution when handling such meats. The cooking temperatures
are easily adjusted to suit your own requirements by turning the
Valve Knob to regulate the degree of heat.
Frying: This option is ideal for stir-fries, sh, breakfast,
pancakes, prawns, paella and vegetables. For this type of
cooking, place the Fat Pan onto the heat shield. Place the Flat
Pan onto the locators of the Fat Pan. Please note that being a
shallow pan, it is not suitable for deep-frying. The easy clean
surface encourages the minimum use of fat for healthy cooking.
Oven Dome / Wok: The dome can be used as a wok, a lid
to create an oven on the BBQ, or a saucepan. For wok-style
cooking, place the dome upside-down directly onto the Pot
stand and use to prepare stir-fries, pasta dishes or paella.
To use the Dome as an Oven lid place the dome over a meal
cooking on the BBQ option for convection style cooking. This
is ideal for roasting chicken, lamp, beef or pork. The Dome can
also be used as a saucepan, to heat sauces, marinades, boil
water, cook rice, pasta etc. Place the dome upside-down directly
onto the Pot Stand.
Boiling: For this type of cooking, place the Pot stand in its
locator grooves on the heat shield ensuring that it is properly
seated. Place a suitable pot (not less than 150mm diameter
and not more than 300mm diameter) or the Safari Chef 2
Dome on the Pot Stand. The Fat Pan has been designed in
such a way that it can also be used as a windshield. One liter
of water will boil in approximately 6 minutes depending on the
conditions, size of pot used, etc. Note: When using small sized
pots do not attempt to use pots with plastic handles. Pot stand
can also be used in the fat pan.
Pizza Baking: For this type of cooking, place the pot stand into
the fat pan. The fat pan has been designed in such a way that it
can also be used as a windshield. Place the pizza stone onto the
pot stand. Pre-heat your pizza stone before use. Ensure that food
is at room temperature before placing it onto the pizza stone, DO
NOT put frozen food onto a heated pizza stone. Put the dome on
to create an oven effect for better heat distribution. For cooking
methods when using the pizza stone, please refer to the pizza
stone user manual.
Pizza Baking
8. Cleaning
BBQ Unit
• To clean the Fat Pan, Flat Pan, and BBQ Grid, wash in warm water with a non-abrasive detergent after rst wiping off any excess fat left
after cooking.
• To Clean the Dome, wash in warm water with a non-abrasive detergent.
• Do not use an abrasive cleaner on any part, as this will damage its surface coating.
• These parts are perfectly safe to clean in the dishwasher after removing any excess fat.
Body / Leg Unit
• This is best cleaned by using a soft damp cloth and a mild non-abrasive detergent. Do not place in a dishwasher as this may allow water
into the valve or burner ports, which will cause the unit to malfunction.
• When cleaning the body/leg unit the pot stand may need to be removed. This can be done lifting the pot stand out of the locator groove in
the heat shield.
9. General Maintenance
• The onus of maintaining this appliance solely rests on the consumer from date of purchase.
• This appliance does not require scheduled maintenance.
• After prolonged storage, inspect the Air Holes under the unit and the inlet of the venturi for insects such as spiders, etc whiich could
affect gas ow. Also inspect the inlet of the Venturi for insects. After checking, ret all components into the prescribed position.
Replacing a Blocked Jet:
• Your Safari Chef 2 is tted with a specic size jet to regulate the correct amount of gas.
• Should the hole in the Jet become blocked, this may result in a small ame or no ame at all. Do not attempt to clean the Jet with a
pin or other such device as this may damage the orice, which could make the appliance unsafe.

6
GB
10. Returning the appliance for repair or service.
• Do not modify the appliance, as this could be dangerous.
• If you cannot rectify a fault by following these instructions, contact your local CADAC distributor for details on how to return the
product for attention.
• Your CADAC Safari Chef 2 is guaranteed by CADAC for a period of 2 years against factory fault.
Fig. 9
Fig. 12
Fig. 11
Fig. 10
Jet
• To replace the Jet: Remove the Fat pan (Fig. 9). Gently unscrew the burner assembly (Fig. 10). Remove the three screws from the heat
shield plate and remove the Heat Shield(Fig. 11), taking care not to damage the piezo electrode. The Jet can now be removed using a
suitable spanner (Fig. 12). Do not use pliers on the jet as this may damage the jet, making it unusable or impossible to remove. Screw
the new jet into the valve. Do not over-tighten as this may damage the jet.
• Reverse the above procedure to re-assemble the unit.
Replacing the Hose:
• The tting of a hose is described in Section 5 - Fitting and replacing the hose and gas cylinder.

77
11. Spares and Accessories
• Always use genuine CADAC spares as they have been designed to give optimum performance.
GB
Item Spare No.
6540-SP011
6540-SP020
6540-SP002
6540-SP004
6540-SP003
6540-SP017
6540-SP005
(2014)
6540-SP005-V2
(2015 onwards)
6540-SP019
Item Spare No.
6540-SP007
6540-SP008
6540-SP037
(Jet 0.65 - 30mbar)
6540-SP038
(Jet 0.59 - 37mbar)
6540-SP039
(Jet 0.56 - 50mbar)
6540-SP055
Front L & R Leg
6540-SP010
Back Leg
6540-SP009
Item Spare No.
6540-300
6540-100
6540-200
6540-600
6540-700
Cover
(300 x 300mm)
6540-800
8635
6544-100
Spares Accessories

8
VORSICHT
Nur im Freien benutzen!
Dieses Gerät darf nicht in einem geschlossenen Balkon, einer Veranda oder einem ähnlichen Bereich benutzt
werden!
WICHTIG
Lesen Sie diese Gebrauchsanweisung bitte sorgfältig durch, um sich mit dem Gerät vertraut zu machen, bevor
Sie es mit seinem Gasbehälter verbinden. Bewahren Sie diese Anleitung zum späteren Nachsehen auf.
DE
1. Allgemeine Informationen
• Dieses Gerät wurde für den Gebrauch im Freien entwickelt und zwar speziell für alle die Campen gehen und das Leben im Freien
genießen. Sie können es aber auch zu Hause auf Ihrer Terrasse benutzen.
• Auf diesem Gerät können verschiedene Gerichte zubereitet werden. Der Safari Chef 2 wurde entwickelt, um mit verschiedenen
Kochoberächen benutzt zu werden.
• Das Gas wird dem Grill über einen Schlauch und einen Regler zugeführt. Der Schlauch und der Regler können an eine Gasasche
oder ein CADAC Power Pak angeschlossen werden (eine Adapter, an dem eine oder zwei Gaskartuschen angeschlossen werden können
- nicht im Lieferumfang des Geräts enthalten).
• Das Gerät kann leicht eingeschaltet und betrieben werden (Abschnitt 6) und die Wärmezufuhr kann vom Benutzer über ein
einstellbares Ventil gesteuert werden.
• Das Gerät wird mit einer praktischen Trage-/
Aufbewahrungstasche geliefert.
• Dieses Gerät entspricht EN 498:2012, EN
484:2019 und SANS 1539:2017.
• Dieses Gerät darf nur mit einem zugelassenen
Schlauch und Regler, der an einen
Gasbehälter angeschlossen ist, betrieben
werden. Der Gasbehälter muss den geltenden
örtlichen Vorschriften entsprechen.
• Dieser Gasbehälter darf nur in aufrechter
Position benutzt werden.
• Warnung: Die zugänglichen Teile können sehr
heiß werden. Kinder entfernt halten.
• Gasgeräte benötigen für eine optimale
Leistung genügend frische Luft. Da Gerät
darf daher nur im Freien genutzt werden den
Gebrauch im Freien bestimmt.
• Lesen Sie diese Anleitung bitte sorgfältig
durch, bevor Sie das Gerät benutzen.
• Nur im Freien benutzen!
6540L0, 6540L1
Benutzungsländer BE, CH, CY, CZ, ES, FR, GB, GR, IE, IT, LT,
LU, LV, PT, SK & SI PL
BE, CY, DK, EE,
FR, FI, HU, IT,
LT, NL, NO, SE,
SI, SK, RO, HR,
TR, BG, IS,LU,
MT, & ZA
AT, CH, DE
& SK
Geräte-Kategorien I3+(28-30/37) I3B/P (37) I3B/P (30) I3B/P (50)
Zulässige Gase Butan Propan Butan, Propan oder eine Mischung daraus
Gasdruck 28-30mBar 37mBar 37mBar
28-30mBar
(2,8 kPa in
Südafrika)
50mBar
Jet Nummer 0.65 0.59 0.65 0.56
Nennverbrauch 130g/hr 130 g/hr 130g/hr 130 g/hr
Nominale brutto
Wärmeeintrag 1.8kW 1.8kW 1.8kW 1.8kW
Ländernamen und Abkürzungen
AE = Vereinigte Arabische
Emirate AL = Albanien AT = Österreich BE = Belgien CH = Schweiz
CZ = Tschechien DE = Deutschland DK = Dänemark ES = Spanien FI = Finnland
FR = Frankreich GB = Großbritannien GR = Griech-
enland HR = Kroatien IT = Italien
JP = Japan KR = Korea NL = Niederlande NO = Norwegen PL = Polen
PT = Portugal RO = Rumänien RU = Russland RS = Serbien SI = Slowenien
SK = Slowakei SE = Schweden TR = Türkei ZA = Südafrika
2. Sicherheitshinweise
• Das Gerät während der Benutzung nicht bewegen.
• Nach der Benutzung das Gas am Gasbehälter abstellen.
• Vor jedem Gebrauch und vor jeder Verbindung mit dem Gasbehälter muss der Schlauch auf Verschleiß und Beschädigung überprüft werden.
• Ist der Schlauch abgenutzt oder beschädigt, darf er mit dem Gerät nicht benutzt werden. Ersetzen Sie den Schlauch.
• Verwenden Sie kein Gerät, das undicht oder beschädigt ist odr das nicht ordnungsgemäß funktioniert.
• Dieses Gerät muss von brennbaren Stoffen während des Gebrauchs ferngehalten werden. Mindestsicherheitsabstände sind: Über dem Gerät:
1,2 m Rückseite und Seiten: 600 mm. (Siehe Abb. 3)
• Achten Sie darauf, dass der Gasbehälter im Freien eingesetzt oder ausgetauscht und von Zündquellen, wie offenen Flammen, Pilotlichtern,
elektrischem Feuer und von anderen Personen fern gehalten wird.
• Gasbehälter dürfen nicht in der Nähe von Hitze und Flammen aufgestellt werden. Legen oder stellen Sie ihn nicht auf einen Herd oder eine
andere heiße Oberäche.
• Achten Sie darauf, dass das zusammengebaute Gerät fest steht und nicht wackelt.
• Falls eine Stichamme auftritt (die Flamme schlägt zurück und zündet sich an der Düse), die Gaszufuhr sofort mit dem Regelventil am
Gasbehälter und danach das Geräteventil schließen. Nachdem die Flamme erloschen ist, müssen Sie den Regler abnehmen und den Zustand
der Dichtung prüfen. Im Zweifelsfall muss die Dichtung erneuert werden. Stellen Sie das Gerät, wie weiter unten im Abschnitt 6 beschrieben,
wieder an. Sollte es wiederholt zu solchen Flammen-Rückschlägen kommen, geben Sie das Produkt bitte Ihrem autorisierten
CADAC-Vertragshändler zurück.