Cadac Meridian 3 98500 User manual

USER INSTRUCTIONSASSEMBLY INSTRUCTIONS
PATIO LIVING
503-0061 LEV2
Please note: Your product may differ from the
image on the front cover
Please note: Your product may differ from the
image on the front cover
Meridian 3 with side burner
Meridian 4 with side burner
98500
98501
0063/09
PIN: 0063BU7867
MERIDIAN 4 WITH SIDE BURNER
98501
MERIDIAN 4 WITH SIDE BURNER
98501

CADAC EUROPE
Ratio 26, 6921 RW Duiven, The Netherlands
Tel: [phone] . Fax: [phone] . Email: [e-mail]
Website: www.cadaceurope.com
CADAC UK
CADAC GERMANY
CADAC FRANCE
CADAC SCANDINAVIA
CADAC SOUTH EAST EUROPE
CADAC AUSTRALIA
CADAC NORTH AMERICA
CADAC MIDDLE EAST
CADAC ZAMBIA
CADAC NEW ZEALAND
CADAC SA
Aven Works, Capel Street, Sheffield, 26 2HN
Tel: [phone] . Fax: [phone] . Email: [e-mail]
Website: www.cadaceurope.com
Bellenstraße 58, 68163 Mannheim
Tel: [phone] . Fax: [phone] . Email: [e-mail]
Website: www.cadaceurope.com
9 Bis Rue du Cot Pilot, 92200 Neuilly Sur Seine
Tel: [phone] . Email: [e-mail]
Website: www.cadaceurope.com
GASVÆRKSVEJ 26C, DK-9000 AALBORG
Tel: [phone] . Fax: [phone] . Email: [e-mail]
Website: www.cadac.dk
Cara Urosa 50, 11 000 Belgrade, Serbia
Tel: [phone] . Email: [email protected]
Website: www.cadac.rs
CADAC-BBQ Pty Ltd . Australia
Tel: [phone] . Email: [email protected]om.au
Website: www.cadacbbq.com.au
1342 South Powerline Road, Bldg. 1 Deerfield Beach, FL 33442, USA
Toll Free: 1-888 602 2322 or Tel: [phone]
Fax: [phone] . Email: jburk[email protected]
Website: www.cadac-barbecues.com
Island View Distributors FZCO, Room 104, LOB 17, jebel Ali Free Zone Authority, Jebel Ali, Dubai, UAE
Tel: [phone] . Fax: [phone] . Email: c[email protected]
Website: www.ivdxb.com
Yunipat Distributors (Z) Ltd. Zambia
P.O. Box 32327 Lusaka ZAMBIA
Tel/Fax: [phone] . Email: [e-mail]
Website: www.yunipatdistributors.co.zm
The Hot Smoke Company Ltd
Factory: 2 Newnham Street Rangiora (CHCH) New Zealand
Tel: [phone] . Fax: [phone]
Email: [e-mail] . jerem[email protected] . ja[email protected]
Website: www.hotsmoke.co.nz
P.O. Box 43196, Industria, 202, South Africa
Tel: [phone] . Fax: [phone] . Email: [e-mail]
Website: www.cadac.co.za

GB
Part No. Description Photo Qty
1 Warming Rack 1
2 Side Burner
Assembly
1
3 Side Table 1
4 Bottom Panel 1
5 Bottom Beam 1
6 Wheel 2
7 Wheel Cap 2
8 Wheel Axle 2

9 Back Panel 1
10 Door Beam 1
11 Drip Bowl 1
12 Drip Pan
1
13 Flame Tamer 3
14 Large Grids
(265mm)
1
15 Right Door 1
16 Left Door 1
17 Dome & Burner
Box
1

18 Castor 2
19 Right Side
Panel
1
20 Left Side Panel 1
21 Fire Box 2
22 Seperation
Panel
1
23 Drip Pan
Handle
1
24 Small Grids
(105mm)
1
25 Grill Plate
1

HARDWARE
A M6*16 Bolt 4pcs
B M6*12 Bolt 16pcs
C Door Pin 2pcs
D φ10 Washer 2pcs
E φ6 Elastic Washer 18pcs
F φ10 Elastic Washer 2pcs
G φ6 Washer 20pcs
H Specific Screw 4pcs
I VE Washer 4pcs
J ST3.9*10
Self-Tapping Screw 4pcs
K M4*10 Bolt 4pcs
L φ4 Elastic Washer 4pcs
M φ4 Washer 4pcs

Step 1: Screw the two Castors(18) onto Right Side Panel(19)
Step 2: Use the M6*12 Bolt (B), through the φ6 Spring Washer (E), φ6 Washer (G) to join the
Back Panel (9) and Side Panels (19,20).

Step 3: Push axle (8) through the Wheel (6), φ10 Spring Washer (F), φ10 Washer(D) and hole
on the Left Side Panel (20). Screw it onto the weld-nut and clip on the Wheel Cap (7).
Step 4: Push the M6*12 Bolt (B) through the φ6 Spring Washer (E), φ6 Washer (G) and fix
Bottom Beam (5) to the two side panels (19 & 20) by screwing it into the riv-nuts on the side
panels.

Step 5: Push the M6*12 Bolt (B) through the φ6 Spring Washer (E), φ6 Washer (G) and fix the
Bottom Panel (4) in position by screwing it into the riv-nuts on the side panels.
Step 6: Use the M6*12 Bolts, Ø6 Spring Washers and Ø6 Washers to fix the Door Beam(10) to
the frame by screwing it onto the Side Panels in the position shown below.

Step 7: Align the slots in the brackets underneath the side tray with the studs in the Right Hand
Side Panel (19). Push the bracket inwards, just enough to clear the studs, and clip the bracket
onto the studs.
Step 8: To fix the Side Burner Assembly (2) to the Left Side Panel (20), take Screw (H) and
place it through Ø6 Spring Washer (E), Ø6 Washer (G) and holes in Left Side Panel (20) and
screw it into the riv-nuts on the left Side Panel.