Calculated Industries 8015 User manual

Conversion Calculator
ULTRA MEASURE MASTER ®
User’s Guide
Tape
CALCULATED INDUSTRIES
®
U LTRA M EASURE M ASTER
®
AC
+ / –
π
Per
EXP
MPa
wt/volmL/sec
Cu m/min m/sec mm/sec
psfpsi
met tons
liters/secoz/sec
gpm
kPa
km/h
ft/min ft/sec in/sec mph
N-min-lbs ft-lbs
BdFt
° F ° C
Hectare Acre-FtAcre
Bars
√__
x
2
÷
8
3
0
456
79
•
1
=
+
+
On/C
–
Off
Inch
Feet
/
Yds
mm
grams
Stor
CONV
km
lbs
dry oz
Sq m
%
kg
liters
fl oz mL
tons
gal
Rcl
Miles
cm
SHIFT
8015UG-E-B 7/31/03 3:43 PM Page 1

Introducing Ultra Measure Master . . . . . . . . . .3
Key Definitions . . . . . . . . . . . . . . . . . . . . . . . .4
Operating Basics . . . . . . . . . . . . . . . . . . . . . .12
Power On & Off . . . . . . . . . . . . . .12
Conventions & Units of Measure . .12
Fractional Settings . . . . . . . . . . . . .15
Preference Feature . . . . . . . . . . . . .16
Basic Math Operations . . . . . . . . . .18
Memory Operation . . . . . . . . . . . . .24
Paperless Tape Feature . . . . . . . . .26
Using the Ultra Measure Master . . . . . . . . . .29
Entering Dimensions . . . . . . . . . . .29
Linear Conversions . . . . . . . . . . . . .30
Area Conversions . . . . . . . . . . . . . .34
Volume Conversions . . . . . . . . . . .37
Weight Conversions . . . . . . . . . . . .41
Weight/Volume . . . . . . . . . . . . . . .44
Temperature Conversions . . . . . . . .47
Linear Velocity Conversions . . . . . .48
Volumetric Velocity Conversions . . .50
Pressure Conversions . . . . . . . . . . .52
Bending Moment Conversions . . . .54
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Accuracy/Errors . . . . . . . . . . . . . . .57
Battery Information . . . . . . . . . . . .58
Specifications . . . . . . . . . . . . . . . . .58
Warranty . . . . . . . . . . . . . . . . . . . .59
TABLE OF CONTENTS
2– Ultra Measure Master
®
8015UG-E-B 7/31/03 3:43 PM Page 2

The Ultra Measure Master ®calculator
simplifies conversions between metric
and English weights and measures. The
Ultra Measure Master can convert the
following types of dimensions:
◆Linear
◆Area
◆Volume
◆Weight
◆Between Weight and Volume
◆Temperature
◆Linear Velocity
◆Volumetric Velocity (Flow Rates)
◆Pressure
◆Bending Moment
In addition to the above, the Ultra
Measure Master performs dimensional
calculations with ease!
INTRODUCING
ULTRA MEASURE MASTER®
User’s Guide – 3
8015UG-E-B 7/31/03 3:43 PM Page 3

[+] [–] [x] [÷] [=]
Arithmetic operation keys.
[0] – [9] and [•]
Digits used for keying in numbers.
[Off] — Off Key
Turns all power off.
[On/C] — On/Clear Key
Turns on power. Pressing once
clears the display. Pressing twice
clears all temporary registers but
does not clear scales.
[Stor] — Storage Key
Used to store values.
[Rcl] — Recall Key
Recalls values stored in registers.
[CONV] — Convert Key
Used with dimension keys to con-
vert dimensions, or with other keys
to access special functions.
[SHIFT] — Shift Key
Used with other keys to access units
of measurement or other special
functions.
KEY DEFINITIONS
4– Ultra Measure Master
®
8015UG-E-B 7/31/03 3:43 PM Page 4

[gal] — Gallon Key
Displays and enters value as gallons.
[fl oz] — Fluid Ounces Key
Displays and enters value as fluid
ounces.
[liters] — Liter Key
Displays and enters value as liters.
[mL] — Milliliter Key
Displays and enters value as milli-
liters.
[%] — Percent Key
Four function percent key.
[tons] — Ton Key
Displays and enters value as tons.
[lbs] — Pounds Key
Displays and enters value as pounds.
[dry oz] — Dry Ounces Key
Displays and enters value as dry
ounces.
[kg] — Kilograms Key
Displays and enters value as kilo-
grams.
[grams] — Grams Key
Displays and enters value as grams.
User’s Guide – 5
8015UG-E-B 7/31/03 3:43 PM Page 5

[Sq] — Square Key
Defines a square dimension.
[m] — Meters Key
Displays and enters value as meters.
[cm] — Centimeter Key
Displays and enters value as centi-
meters.
[mm] — Millimeter Key
Displays and enters value as milli-
meters.
[km] — Kilometer Key
Displays and enters value as kilometers.
[Yds] — Yards Key
Displays and enters value as yards.
[Feet] — Feet Key
Displays and enters value as decimal
feet; enters the feet portion of a feet-
inch value.
[Inch] — Inch Key
Displays and enters value as deci-
mal inches; enters the inch portion
of a feet-inch value.
[/] — Fraction Key
Used to separate the numerator and
denominator when entering frac-
tions: 1 [/] 2
6– Ultra Measure Master
®
8015UG-E-B 7/31/03 3:43 PM Page 6

[Miles] — Miles Key
Displays and enters value as miles.
[SHIFT] [gal] — Gallons Per Minute
Displays and enters value as gallons
per minute (gpm).
[SHIFT] [fl oz] — Fluid Ounces Per Second
Displays and enters value as fluid
ounces per second (oz/sec).
[SHIFT] [liters] — Liters Per Second
Displays and enters value as liters
per second (liters/sec).
[SHIFT] [mL] — Milliliters Per Second
Displays and enters value as milli-
liters per second (mL/sec).
[SHIFT] [%] — Weight Per Volume
Displays and enters weight per vol-
ume factor in permanent memory.
[SHIFT] [tons] — Metric Tons
Displays and enters value as metric
tons (met tons).
[SHIFT] [lbs] — Pounds Per Square Inch
Displays and enters value as pounds
per square inch (psi).
[SHIFT] [dry oz] — Pounds Per Square Foot
Displays and enters value as pounds
per square foot (psf).
User’s Guide – 7
8015UG-E-B 7/31/03 3:43 PM Page 7

[SHIFT] [kg] — Kilopascals
Displays and enters value as kilo-
pascals (kPa).
[SHIFT] [grams] — Megapascals
Displays and enters value as mega-
pascals (MPa).
[SHIFT] [Sq] — Cubic Function
Defines a cubic dimension (Cu).
[SHIFT] [m] — Meters Per Minute
Displays and enters value as meters
per minute (m/min).
[SHIFT] [cm] — Meters Per Second
Displays and enters value as meters
per second (m/sec).
[SHIFT] [mm] — Millimeters Per Second
Displays and enters value as mil-
limeters per second (mm/sec).
[SHIFT] [km] — Kilometers Per Hour
Displays and enters value as kilo-
meters per hour (km/h).
[SHIFT] [Yds] — Feet Per Minute
Displays and enters value as feet per
minute (ft/min).
[SHIFT] [Feet] — Feet Per Second
Displays and enters value as feet per
second (ft/sec).
8– Ultra Measure Master
®
8015UG-E-B 7/31/03 3:43 PM Page 8

[SHIFT] [Inch] — Inches Per Second
Displays and enters value as inches
per second (in/sec).
[SHIFT] [Miles] — Miles Per Hour
Displays and enters value as miles
per hour (mph).
[SHIFT] [9] — Newton-meters
Displays and enters value as new-
ton-meters (N-m).
[SHIFT] [8] — Foot-Pound
Displays and enters value as foot
pounds (ft-lbs).
[SHIFT] [7] —Inch-Pounds
Displays and enters value as inch
pounds (in-lbs).
[SHIFT] [6] — Acre-Feet
Displays and enters value as acre-feet.
[SHIFT] [5] — Acre
Displays and enters value as acres.
[SHIFT] [4] — Hectare
Displays and enters value as hectares.
[SHIFT] [3] — Fahrenheit
Displays and enters value as
Fahrenheit (°F).
User’s Guide – 9
8015UG-E-B 7/31/03 3:43 PM Page 9

[SHIFT] [2] — Celsius
Displays and enters value as Celsius
(°C).
[SHIFT] [1] — Board Feet
Displays and enters value as board
feet (BdFt).
[SHIFT] [•] — Per Unit Function
Allows you to calculate total material
cost, if you multiply the total amount
of material by the per unit cost of the
item.
[SHIFT] [–] — Change Sign
Toggles the sign of the displayed
value. (Positive or negative.)
[SHIFT] [÷] — Square Root Function
Calculates and displays the square
root of a number. You will get an
error if you try to find the square
root of a linear or volume value.
[CONV] [+] — Pi Constant (π)
An internal constant: 3.141593.
[CONV] [/] — Exponential Notation
Used to enter exponential values.
[CONV] [Rcl] — Memory Clear
Clears the value in memory without
changing the display.
10 – Ultra Measure Master
®
8015UG-E-B 7/31/03 3:43 PM Page 10