California Faucets Descanso CF-TO-V3002-7 User manual

CF-TO-V3002-X_ii_190131 Pg 1
Descanso®
CF-TO-V3002-7, CF-TO-V3002-9
CF-TO-V3002X-7 & CF-TO-V3002X-9
In-Wall Vessel Lavatory Faucet
Installation Instructions
1
IMPORTANT: Read all instructions prior to installation and provide copy of instructions to consumer.
Operating Specifications:
Recommended Supply Pressure: 20 to 70 psi *†
Maximum Flow Rate: 1.2 gpm
*Operating pressures between hot and cold supplies should vary no more than 30 psi.
†If water pressure exceeds 70 psi, install a Pressure-Reducing Valve (PRV).
INSTALLING SPOUT TO IN-WALL VALVE
•Prior to installing faucet trim in-wall vessel rough
VALVE (1), CF-VL-R, must be properly installed
and wall surface must be completely finished
NOTE: Recommended through-hole size shall be Ø1-1/4”
•Apply thread sealant to both threaded ends of NPT
NIPPLE (2), not supplied, and tighten into center
outlet of VALVE (1)
•Tighten spout BASE (4) onto spout RING (5), and
slide onto SPOUT (3)
•Tighten SPOUT (3) onto NPT NIPPLE (2)
•If SPOUT (3) is not properly aligned when fully
tightened, turn counter-clockwise till properly
aligned
IMPORTANT: Do not overtighten SPOUT (3)
•Push spout RING (5) firmly against wall, positioning
setscrew hole on bottom, and tighten SETSCREW
(6)
CALIFORNIA FAUCETS RECOMMENDS THAT ALL PLUMBING PRODUCTS BE INSTALLED
BY A LICENSED PROFESSIONAL
1
2
Ø1-1/4”
(3 holes)
4
3
5
6
1a

CF-TO-V3002-X_ii_190131 Pg 2
2
3
4
v ALIGN & TRIM VALVE STEM
•Remove MUDGUARD (1a) from VALVE (1)
•To obtain proper HANDLE (11) alignment it may
be necessary to re-align cartridge STEM (1b); to
align STEM (1b), slightly loosen the cartridge NUT
(1d), place HANDLE (11) on STEM (1b) and
TIGHTEN in CW direction until desired
alignment is achieved; retighten cartridge NUT (1d)
to factory torque setting of 14 ft-lbs.
WARNING: Cartridge NUT (1d) MUST be properly torqued to
prevent possible failure and/or water damage
•Using a marking device (e.g. pencil or marker)
indicate a distance of 13/16” from finished wall on
ALL-THREAD (1c); unscrew ALL-THREAD (1c)
from valve STEM (1b)
•Cut STEM (1b)1-3/4” from finished wall surface
•Cut off excess ALL-THREAD (1c) at indicated mark
and reattach ALL-THREAD (1c)onto valve STEM
(1b)–repeat on other side
INSTALLING ESCUTCHEON
•Tighten handle RING (8) and decorative NUT (10)
onto handle RISER (9)
•Secure escutcheon onto wall by tightening
decorative NUT (10) onto ALL-THREAD (1c)
INSTALLING HANDLE
•Loosen both SETSCREW (11b)
•Slide HANDLE (11) down onto and engage valve
STEM (1b) leaving a space of 1/32” between handle
and decorative NUT (10)
•Tighten both SETSCREW (11b)
•Turn on water supply and check for leaks
californiafaucets.com 5271 Argosy Ave. Huntington Beach, CA 92649 800-822-8855
1c
10
9
8
11
11
1b
11b
11
1d
1c
13/16”
hex
1b
1b
1-3/4”
1c
13/16”
10