Camplex CMX-FG700 User manual

USER MANUAL
CAMPLEX FIBERGIG
2-Channel Bidirectional GigaBit Ethernet
Fiber Optic Transport
CMX-FG750—ST Fiber I/O
CMX-FG700—opticalCON Quad I/O

CMX-FG700/FG750
Camplex 2-Channel Bidirectional GigaBit Ethernet
Fiber Optic Transport

The Camplex FIBERGIG CMX‐FG700 is 2 separate 1GIGe Ethernet to fiber me‐
dia converters in convenient 1RU rack mount cabinets. Each channel is a Gig‐
bit Ethernet over a singlemode fiber opc data transport system in a rack‐
mount enclosure with either one opcalCON quad
connector (model FG700) or four ST connectors (model FG750) . The
transport system is a convenient rackmount soluon for transporng data
and power as it meets PoE standards.
The system converts IEEE 802.3at/af copper Ethernet to long distance or re‐
mote connecon points with singlemode fiber up to 12 miles. This is a perfect
interface soluon for Dante devices that require LAN to communicate with
other devices. Designed for remote trucks, field
producon, and live events, saving installaon me. A single IEC AC power
cord powers each TX and RX unit reducing the number of cables.
Includes
 Two 1RU cabinets; one TX and one RX unit
 Two standard 6 foot IEC type power cords
 Rack screws for installaon in a standard 19” equipment rack
Features
 Up to 30 was of power per port via PoE standards
 Gigabit Ethernet features 1000BaseT to 1000BaseX fiber media conver‐
sion
 Ethernet spec meets DANTE requirements 802.3at/af
 Convenient single rack unit enclosure with front panel
connecons for each Tx and Rx unit
 Standard IEC 110/240vac 50/60Hz power inlet on back panel
 Singlemode fiber connecon on either opcalCON Quad
or four ST fiber connecons
 Transmission range: 12 miles (20km)
 Lightweight, rugged, aluminum cabinet
Camplex CMX‐FG700/CMX‐FG750 Page 2

Camplex CMX‐FG700/CMX‐FG750 Page 3
CMX-FG700/FG750
Specificaons

 GigE ethernet copper and fiber
 802.3at/802.3af PoE standards compliance
 1000BASE‐T to 1000BASE‐X
 RJ45 to fiber Ethernet converter port [2X: separate
Ethernets out of the box, combinable if desired]
 Black anodized aluminum housing
 Rugged Neutrik/Senko connectors
Camplex FiberGig Series
CMX‐FG500
2 Ch 3G‐SDI,
CMX‐FG550
2 Ch 3G‐SDI,
CMX‐FG650
2 Ch 3G‐SDI & GIG‐E,
CMX‐FG600
2 Ch 3G‐SDI & GIG‐E,
CMX‐FG750
CMX‐FG700
2 Ch GIG‐E,

Camplex CMX‐FG700/CMX‐FG750 Page 4
CMX-FG700 Features
Transmier
2345
678
Receiver
1
910
CMX‐FG700Transmier
1Power Switch 2Status LED Indicators 3Converter 1 802.af/at Media I/O 4Converter 2 802.af/at Media I/O 5opcalCON Quad I/O
CMX‐FG700Receiver
6Power Switch 7Status LED Indicators 8Converter 1 802.af/at Media I/O 9Converter 2 802.af/at Media I/O
10opcalCON Quad I/O

Camplex CMX‐FG700/CMX‐FG750 Page 5
CMX-FG750 Features
Receiver Transmier
12345
678910
CMX‐FG750Receiver
6Power Switch 7Status LED Indicators 8Converter 1 802.af/at Media I/O 9Converter 2 802.af/at Media I/O
10Four ST I/O
CMX‐FG750Transmier
1Power Switch
2Status LED Indicators
3Converter 1 802.af/at Media I/O
4Converter 2 802.af/at Media I/O
5Four ST I/O

CMX-FG700/FG750 Features
Back Panel
CMX-FG700/750 Set Up Instructions
1. Secure the units in a safe locaon, where they will not be subject to im‐
pact and where there is room around the unit so nothing will interfere
with the fiber opc cabling causing it to bend sharply in a ght radius in
any way which can severely affect the signal transfer.
2. Carefully connect your source(s) to the transmier input(s) and the re‐
ceiver unit output(s) to your receiving device input(s) using the Cat5/5e/6
UTP RJ45 cable connectors on the transmier and on the receiver unit.
3. CLEAN* the fiber opcal cable contacts that will be used for connecng
the Tx and Rx units and aach the fiber cable to the
connecons and secure, as you would secure a bayonet BNC. While
pressing lightly in on the connector, twist it in a clockwise direcon about
1/8 to 1/4 of a turn and then release. The connector should stay inserted
and have backwards spring pressure holding the bayonet in place.
4. Connect the included power supplies to the transmier & receiver units,
and plug them both into an AC power source.
Camplex CMX‐FG700/CMX‐FG750 Page 6
Receiver
CMX‐FG700/750Transmier&Receiver
11AC Power Input 2A/110‐240VAC 50/60Hz
11
11
Transmier

Camplex CMX‐FG700/CMX‐FG750 Page 7
* CLEAN: All fiber opcal cable contacts (the end that is inserted and makes
contact to enable light wave transmission through the fiber)
require cleaning each me before inserng into a device’s outputs or inputs.
Failure to clean the contacts can damage the unit’s opcs over me and also
render the cable and the device nonoperaonal.
Use cleaning kits designed specifically for fiber opcs. Other cleaners may
add contaminants not seen by the naked eye which could damage cables
and/or equipment.

The
SAFETY PRECAUTIONS

1. To prevent fire or shock hazard, do not expose this equipment to
high humidity and/or dust. Do not use in an unprotected outdoor
installaon nor any area classified as overly damp.
2. The temperature for installaon should be kept between 32°F to
140°F (0°C to 60°C). Avoid direct sunlight exposure or extreme
changes of temperature over a short period of me.
3. Do not disassemble the unit or place it on an unstable base.
4. Do not drop the unit and avoid heavy impact.
5. This unit should not be permanently installed unless proper ven‐
laon is provided. Any enclosure openings must not be blocked or
covered as they protect the unit from overheang.
6. Before cleaning, turn offthe power and unplug the unit from all
connecons. Use a damp cloth. Do not use liquid or
aerosol cleaners.
7. Do not overload outlets and extension cords as this may
result in a risk of fire or electric shock.
8. Enclosure entry is dangerous. Never push objects of any kind, in‐
cluding liquids, into this unit through openings as they may touch
dangerous voltage points or short‐out parts that could result in a
fire or electric shock.
9. Do not aempt to open or service this unit yourself as
opening or removing covers may expose you to dangerous voltage
and other hazards.
10. There are no user‐serviceable parts inside the unit. If the unit re‐
quires service contact your authorized dealer, or an
authorized repair service company.
Camplex
812KingsHighway
Saugeres,NY12477
www.camplex.com