Campomatic DW814EW User manual

DW814EW / DW914ES
INSTRUCTION MANUAL
:
WWW.CAMPOMATIC.COM
Dishwasher
Made in China

Witheachwashcycle.
Compartment
For programmes with pre-wash only.
(Follow the user instructions!)
Electric indicator on control panel (if provided).
Check the rinse aid level
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Check the regeneration
salt level
Load the baskets
Close the door, turn on the water tap and press the Start/reset button. The machine will start working
after about 10 seconds.
Running the dishwasher
Switch off the appliance
Turn off the water tap,
unload the baskets
Fill the detergent dispenser
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will alsodry better.Unload the appliance, startingfrom the lower basket.
Changing theprogramme
Add forgotten dishes in the
dishwasher.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the ON/OFF button.
If the appliance is switched
off during a wash cycle.
Open the door carefully.
Hotsteammay escape
when thedoorisopened!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch on the appliance Press the On/Off button to switch on the appliance, Open the door.
1.Open the door a little to stop the dishwasher.
2.After the spray arms stop working, you can open the door completely.
3.Add the forgotten dishes.
4.Close the door, the dishwasher will start running again after 10 seconds.
For detailed operating method read the corresponding content on the instruction manual.
1. Arunning cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Press the Start/Reset button for more than 3 seconds to cancel the running programme.
3. Select a new programme.
4. Restart thedishwasher.
Select a programme
Turn the knob to select the desired programme
( See the section entitled Operationg instruction )“”

To review the section on troubleshootingTips
will help youto solve some common problems
by yourself .
The manufacturer, following a policy of constant
developmentandupdating of the product, may
make modificationswithout giving prior notice.
Dishwasher Features.................................... ...3
A WaterSoftener..................... ....................4、..
Attention before orafter loading the Dishwasher
Baskets..........................................................9
FilteringSystem.............................................15
Caring for the Dishwasher..................... .........16.
B Loading the Salt into the Softener.................5、
C Fill theRinseAid Dispenser.........................5、
D Function ofDetergent .................................6 、
Loadingthe upper ...............................10Basket
LoadingtheLower ...............................10Basket
Cutlery Basket........................................... ...11
Therecommended method loading big
dishware.................................................... ...12
WashCycleTable...........................................13
Turning on theAppliance................................14
Change the Programme.............. ................14....
At the End of theWash Cycle...........................14
PositioningtheAppliance................... ..........17..
Water Connection.................................. .......18.
About Power Connection........................ .......17.
Start of dishwasher................................ ......19..
Beforecallingfor service........................... .....20.
Errorcodes.................................... ..............21.
Technical information.............................. .....22..
ControlPanel...................................................3
If you can not solvethe problems by yourself ,
please ask for the help of professional technicians.
Dear Customer,
Please carefullyreading itbeforeusing the dishwasher
will help you touse and maintain the dishwasher properly.
Pass it on to any subsequent owner of the appliance.
This manual contains sections of Safety Instructions,
OperatingInstructions,InstallationInstructionsand
Troubleshooting Tips,etc.
Keep it to refer to at a later date.
This appliance is intended tobe used in household
and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients in hotels, motels and other residential
type environments;
-bed and breakfasttypeenvironments.

This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of anelectric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipment-
grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Keep children away from detergent and rinse aid, keep
child away from the open door of the dishwasher,
there could still be some detergent left inside.
ren
Donotabuse,siton,orstandonthedoorordish
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
(This instruction is only applicable to machines
with a visual heating element.)
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
Do not place any heavy objects the
door when it is open. The appliance could tip
forward.
on or stand on
When loading items to be washed:
1) Locate sharp items so that they are not likely
to damage the door seal;
2 Warning: Knives and other utensils with
sharp points must be loadedinthe basket
with their pointsdown or placed in a
horizontalposition.
)
When using your dishwasher, youshould
prevent plastic items from coming into contact
with the heating element.(This instruction is only
applicable to machines with a visual heating
element.)
Ifthesupplycord isdamaged, it must bereplaced
bythemanufactureroritsserviceagentora
similarly qualified person in order to avoid a
hazard.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Dishwasher detergents are strongly alkaline, they
can be extremelydangerousif swallowed.Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
Check that the detergent comparment isempty
after completion of thewash cycle.
The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
The maximum number of place settings to be
washed is12.
The maximum permissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa.
Children should be supervised to ensure that they do
not play with the appliance.
This appliance is not intended for use by persons
(including children with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
)
When using your dishwasher, follow the precautions listed below:
The door should not be left open,
since this could increasethe riskof tripping.
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.

Packaging materialcouldbedangerous for children!
Fordisposing ofpackage and the appliance please goto arecycling centre. Therefore cut
off the powersupplycable and makethe doorclosing device unusable.
Cardboard packaging ismanufactured from recycled paperand shouldbe disposedin the
waste papercollection for recycling.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriatewaste handling of this product.
Formoredetailed information about recycling of this product, please contact your local
city office and your household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.






11 12
Back View
1
2
3
4
5
6
7
8
9
10
on
Of f
Front view
MainFilter
Detergent Dispenser
CupShelf
CutleryBasket
CoarseFilter
RinseAid Dispenser
Inlet pipe connector
Drain pipe connector
Lower Basket
SprayArms
UpperBasket
1
Salt Container
beforeusing it forthe first time.
To getthe best performance from yourdishwasher,read all operating instructions
5
6
7
8
9
10
12
11
3
24
Salt and rinse aid warning lights: To show
when the salt container or dispenser need to be
refilled
Start and reset button: To start and pause the
selected washing program or reset the washing
program when the machine is working.
Washing Program Selector: Turn the knob to
select wash cycles .
65
6
4
5
Allin 1 function button and indicatorlight : The indicator
light will beon when you select this function.
Power indicator light and switch: To turn on/off
and showthepower supply.
Running indicator light : To show the state of the
dishwasher.
4
2
3
2
3

Before using yourdishwasher for the first time:
The water softener must be set manually, usingthe water hardness dial.
The water softeneris designed to remove mineralsandsalts from the water, which wouldhave
a detrimentalor adverse effect on the operation of the appliance. Thehigherthe
content of these minerals and salts, the harder your water is. The softener should be
adjusted accordingtothe hardness ofthe water in yourarea. Your localWaterAuthority
can advise you onthehardnessofthe waterinyourarea.
Adjusting Salt Consumption
The dishwasher isdesigned toallow for adjustment in the amount of salt consumed based onthe hardness of
the waterused.This is intended tooptimise and customisethelevelo f salt consumption.
1. Unscrew the cap fromthe salt container.
2. There is a ring on the container with anarrow on it (see figure
ontheside),ifnecessary, rotate the ring intheanticlockwise
direction from the "-" Setting toward the"+"sign, basedon the
hardness ofthe water being used.
It is recommendedthat adjustments should be made in
accordance withthe following scheme:
WATER SOFTENER
Thehardness ofthe watervariesfromplace to place.If hard water isused inthe dishwasher, deposits will
form on the dishesand utensils.
The appliance is equipped with a special softener thatuses a salt container specifically designed to eliminate
lime and minerals from the water.
Contact your local water board for information on the hardnessof your water supply.
dH mmol/l
0~140~8 0~1.4 /0/
14~398~22 1.4~3.9 - 20 50
39~8022~45 3.9~8 Mid 40 25
+60 16
fH
0~10
10~28
28~56
Clarke
WATER HARDNESS
SelectorPosition Salt consumption
(gram/cycle) Auto nomy
(cycles/1kgs)
Please follow the steps below for adjustment in salt consumption.
""/
"-"
"+"
"Mid"
Settingtowardthe"+"sign
Settingtowardthe"-"sign
Settingtowardbetween
the "-" sign and "+" sign
No salt need added
45~60 80~107 56~75 8~11
If your model does not have any water softener, you mayskip this section.
A. Set the watersoftener
B. Pour 1 2 litre of water insidethesaltcontainer and then fill withdishwasher salt
／
C. Filltherinseaiddispenser
D. Fill in detergent
°Clark: British degree
°fH: French degree
°DH: German degree
dH=1.25Clarke=1.78fH=0.178mmol/l
°°°
1

normal for a small amount of water to come out of the salt container.Itis
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well thesalt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (forsome Models),you can estimate when to fill
the salt into the softener by the cycles that the dishwasherhas run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excessivesalt.
Always use the salt intended for use with dishwasher.
The salt container is located beneath the lower basket and shouldbefilled as explained
inthe following:
Attention!
Only use salt specifically designed forthe use indishwashers! Every other type of
salt not specifically designed for theuse in a dishwasher, especially table salt, will
damage thewater softener. In case of damages caused by the use of unsuitable
salt the manufacturerdoes not give any warranty nor is liable for any damagescaused.
Only fill withsalt justbefore starting one of the complete washingprograms.
This will prevent anygrains of salt or salty water, which may have been spilled,
remaining on the bottom ofthe machinefor any periodof time, which maycause
corrosion.
The rinse aid isreleasedduring the final rinseto prevent water from forming droplets onyour dishes, which can
leave spots andstreaks. Italso improvesdryingby allowing water toroll offthe dishes. Your dishwasheris
designed touseliquidrinseaids. The rinseaid dispenser islocated inside the doornext to the detergentdispenser.
To fill the dispenser,open the cap and pour the rinse aid into the dispenser until the level indicator turns completely
black. The volume ofthe rinseaidcontainer is about 110ml.
RinseAid Dispenser
Function of RinseAid
Rinse aid is automaticallyadded during thelast rinse, ensuring thorough rinsing, and spotandstreakfree drying.
Attention!
Only use branded rinseaid for dishwasher. Never fill therinse aid dispenserwithanyother substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
ARemove the lower basket and then unscrew andremovethe cap fromthesalt container.
BBefore thefirst wash, fill 1lt. of water in the salt container of your machine.
CPlace theend of thefunnel (supplied) into the hole and introduce about 1kg of salt.
DAfter filling the container , screw the cap tightly back clockwise.
EUsually, the salt warning light will stop being illuminated within 2-6 days afterthesalt containerhasbeen filled with
salt.
FImmediately after filling the salt into the salt container, a washing program should be started
program Otherwise the filter system, pump or other important parts of the machine may be damaged
bysalty water.This isoutofwarranty.
(Wesuggest to use the
soak orrapid ).

To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pourthe rinse aid intothe dispenser, being careful not to overfill.
Replace the cap by inserting italigned with "open" arrow and turning it to the closed (right) arrow.
Adjusting RinseAid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are a problem, increase the amount of rinse
aid dispensedby removing the dispenser lidand rotating the dial to "5". If the
dishes still are not drying properly or are show spots, adjustthe dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of wateror limespots onthe dishes after washing.
Reduce it ifthere are sticky whitish stains on your dishes or abluish film on glasswareor
knife blades.
1
2
3
As the rinse aid diminishes, the size of the black dot
ontherinse aidlevel indicator changes, as illustratedbelow.
Full
3/4full
1/2full
1/ 4full- Should refilltoeliminate spotting
Empty
When to Refill the RinseAid Dispenser
Ifthereis no rinse-aid warning lightin thecontrolpanel, you can estimate the amount from the colour
of the optical level indicator C located next to the cap. When the rinse-aidcontainer isfull, the whole
indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let
the rinse aid level fall 1 / 4 full.
during the nextwash. Don'tforget to replacethe cap before you closedishwasher door.
Clean up any rinse aid spilled while during fillingwith an absorbent cloth to avoid excessive foaming
Detergents with its chemical ingredients arenecessary toremove dirt,crush dirt andtransport it outof the dishwasher.
Mostofthe commercial quality detergents are suitable for this purpose.
Detergents
Thereare 3 sorts of detergents
1.With phosphate and withchlorine
2.With phosphate andwithout chlorine
3.Withoutphosphate and without chlorine
""

Proper Use ofDetergent
Use only detergent specificallymade for theusein dishwashers.Keep your detergent fresh and dry.
Don'tput powdereddetergentinto the dispenseruntilyou'reready towash dishes.
Dishwasher detergent is corrosive! Takecare to keepit out of reach of children.
Based ontheir chemical composition, detergentscanbe splitintwo basic types:
The use of normal washingprograms incombination with concentrated detergents
reduces pollution and is good for your dishes; these wash programsare specifically matched
to the dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason
normal wash programsin whichconcentrated detergentsareused canachieve the same
results that can otherwise onlybe achieved using intensive programs.
“”
“”
“”
Detergent tabletsof different brands dissolve at different speeds. For this reasonsome
detergenttablets cannot dissolve and develop theirfull cleaning power during short
programs. Therefore please use long programs whenusingdetergent tablets, to
ensure the complete removal of detergent residuals.
The dispenser must be refilled before the start ofeach washcycle following the instructions
provided in the wash cycle table . Yourdishwasher usesless detergent and rinse aid than
Conventionaldishwasher.Generally, only one tablespoon of detergent is neededfor
anormal washload. Moreheavily soileditemsneed more detergent.Alwaysaddthe
detergentjust before starting the dishwasher, otherwise it couldget damp and will not
dissolve properly.
Concentrated Detergent
DetergentTablets
DetergentDispenser
conventional, alkaline detergents with caustic components
low alkalineconcentrated detergents with natural enzymes
Normally new pulverised detergent is without phosphate.Thus the water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt containereven when
the hardness of water is only 6 dH. If detergents without phosphate are used in the case of hard water
often white spots appear on dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strongand coloured spots will not
be removed completely.Inthis case pleasechoose a program with a higher temperature.
°
Amount ofDetergent toUse
Always add the detergent just before starting each wash cycle.
Only use branded detergentaidfor dishwasher.
If the lid isclosed: press release button.The lid will spring open.
Detergent tablet
Detergent powder

Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on the right:
Theplace of main wash cycle detergent placed.
Theplace of pre-wash cycle detergent placed.
Please observe the manufacturers dosing and storage
Recommendationsas statedonthedetergent packaging.
Close thelid and press untilit locks in place.
If the dishes are heavily soiled, place an additional
detergent dosein the pre-wash detergent chamber.Thisdetergent will take effectduring the pre-washphase.
A
B
Fill in Detergent
You findinformation about the amount ofdetergent for thesingle programme onthe last page.
Pleaseaware, thataccording tothe levelsoiling and the specific hardnessof water differencesarepossible.
Pleaseobservethemanufacturer's recommendations onthe detergent packaging.

Cutlery withwooden,horn china or
mother-of-pearl handles
Plasticitems that arenotheat resistant
Older cutlerywith glued parts that are not
temperatureresistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items madefromsyntheticfibres
Some types of glassescan become
dull aftera large number of washes
Silver and aluminum parts have a
tendencyto discolourduringwashing
Glazed patterns may fade if machine
washed frequently
Are not suitable Are oflimited suitability
Dishesand items of cutlery mustnot lie inside oneanother, or cover eachother.
To avoid damage to glasses, theymust not touch.
Load large itemswhich are most difficult to cleaninto the lower basket.
The upper basket isdesigned to hold more delicate and lighter dishware such as glasses, coffee
andteacups
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knivesmust be positioned
horizontallyin the upper basket.
Please do not overload your dishwasher. This is importantfor good resultsandfor
reasonable consumptionof energy.
Load hollow items suchas cups,glasses, pans etc. With the opening facing downwards so that
water cannot collect in the container or a deepbase.
Consider buyingutensils which are identified asdishwasher-proof.
Usea mild detergentthatis describedas 'kind todishes'. If necessary, seekfurther
information from thedetergent manufacturers.
Forparticular items,select aprogramwithas low a temperature aspossible.
To prevent damage, do not take glassandcutlery out of the dishwasher immediately
after the programmehas ended.
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlerybaskets may vary from your model.)
Scrape off any largeamounts ofleftover food. Soften remnants of burnt food in pans.
It is not necessary to rinse thedishesunder running water.
Place objects in the dishwasher in following way:
1.Items such ascups, glasses, pots/pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tipover.
4.All utensils are placed in the way that the spray arms can rotate freely duringwashing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
To prevent water dripping from the upper basket into the lower basket, we recommend thatyou
empty the lower basket first and then the upper basket.

The upperbasket isdesigned tohold more delicate andlighter dishware suchas glasses,coffee
and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are
not toodirty).
Position the dishes and cookware so that they will not get moved by the spray of water.
Wesuggest that you place largeitems and the most difficultto clean items are tobe placed into thelower basket:
such as pots, pans,lids, serving dishesand bowls, as shownin the figurebelow.
It is preferableto placeserving dishes and lids on the side of theracks inorder toavoid blocking the rotation ofthe
topspray arm.
Pots, serving bowls,etc, must always be placed top down.
Deep pots should be slanted to allow water toflowout.
Please be reminded that:
The Bottom Basket features folding spikesso that larger or more pots and panscanbe loaded.

2
4
3
1
5
1
5
6
1
Cups
Saucers
6Medium serving bowl
3
Large servingbowl
45
Glasses
1cups
Small serving bowl
2

Cutlery should be placed in the cutlery basket with the handles at the bottom.If the rack has side baskets,the
spoons should be loaded separately into the appropriate slots, especially long utensils shouldbeplacedin the
horizontal position at the front ofthe upperbasket as shown in the picture.
Folding Spikes of Lower Basket
For better stacking ofpots and pans,
the spikes can be folded down as
show in the picture right.
Do not let any item extend through the bottom.
Always loadsharp utensils with the sharp point down!
Adjusting the Upper Basket
The height of the upper basketcanbe adjusted in order to create more space for large utensils
both for the upper/lower basket. The height of the upper basket canbe adjusted by placing the
wheels on different height of the rails. Long items, serving cutlery, salad servers and knives
should be placed on the shelfso that they do not obstruct the rotationof the spray arms.
The shelf can be folded back or be removed when not required for use.

Means:need to fill rinse into the Rinse-Aid Dispenser.
()
*EN 50242 : This programme isthe test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 12 setting
PositionUpper basket: upper wheels onrails
Rinse aid setting: 6
Eco.
Normal
(*EN 50242)
For normally soiled loads,
such as , plates,glasses
and lightly soiled pans.
standard daily cycle.
pots
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
A shorter wash for lightly
soiled loads that do not
need drying.
Rapid
Pre-wash(50 )
Wash (50 )
Rinse
Rinse (65 )
Drying
℃
℃
℃
Wash (40 )
Rinse
Rinse (45 )
℃
℃
20 g.
160
30
1.2
0.45
16
12
Draw out the lower and upper basket, load the dishes and push them back.
It iscommendedtoloadthelowerbasketfirst,thentheupperone(seethe sectionentitled
Loading the Dishwasher ).
Pour in the detergent (see the section entitled Salt, Detergent and RinseAid ).
Insert the plug intothe socket. The power supplyis 220-240 VAC /50 HZ, the specification of the
socketis 10A 250VAC. Make sure thatthe water supply is turnedon to fullpressure.
Close the door, press the ON/OFF button, and the ON/OFF light will turn on.Turn the program
knob to selecta desired wash cycle, press the Start/Reset button, the machine will work .
“”
“”
after 3seconds
1
2
3
4
(OrAll )in1
5/25g
Wash (50 )
Rinse (65 )
Drying
Pre-wash
Pre-wash
℃
℃
(OrAll )in1
5/25g 155 1.05 16

It is dangerousto open the door when washing, because the hot water may scald you.
When the working cycle has finished, the buzzer of the dishwasher will soundfor 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off thewater supply and open the door of the dishwasher.
Wait for afew minutes before unloading the dishwasherto avoidhandlingthe dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
The runningindicator light is off, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turnoffthewater tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should thereforebeallowed to cool down around 15 minutes
before removingfromthe appliance.
Open thedishwasher's door, leave it ajar and wait afew minutes before removing the dishes. In this way they
will be cooler andthe drying will be improved.
Unloadingthedishwasher
It is normal that the dishwasher is wet inside.
Empty thelower basket first and thenthe upperone. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
If you open the door , the machine will pause. The runningindicator
light will stop blinkingand the buzzerwillmooing every minuteunless you close thedoor.
After you close the door ,the machine will keep on working after 10 seconds.
during awash cycle
Aforgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working,you can open the door
completely.
2
3
Open the door a little to stop the washing.
14
5
6
Press the start/reset button
Press the start/reset button, the dishwasher will run
after 10 seconds.
When you pressthe Start/Reset button to pause duringwashing, the running indicator
light will stop blinking and the dishwasher will mooing every minute unless you press the
Start/Reset button to start.
Acycle that is underway can only be modified if it has only been running for a short
time. Otherwise, thedetergent may have alreadybeen released, and the appliancemay
have already drained the wash water. If this is the case, the detergent dispenser must
be refilled (see the section entitled " Loading the Detergent " ).
When youpressthestart/reset button more than 3 seconds, you can cancel the running
programme andselect other programmes (see the sectionentitled "Starting awash cycle. .. " ).
Whenyou select Normal/Eco.Programmes, you can selecttheAll in1 function.
The Display window shows the state of the dishwasher:
a) Running indicator light is off ----------------------------------> standby;
b) Running indicator light is on and not blinking -------------> pause;
c) Running indicator light is on and blinking ------------------------> run.
1
2
3
4
Premise

The filter prevents larger remnants of food or other objects from getting insidethepum.
Theresidues may blockthefilter, inthiscasethey must be removed.
The filter system consists of a coarse filter,a flat (Main filter)
And a microfilter(Fine filter).
Food and soil particles trapped inthisfilter arepulverizedby a
special jet on the lower spray arm andwasheddown todrain.
Larger items, such as pieces of bonesor glass, that could block
the drain aretrappedin the coarse filter.To remove the items
caught by the filter, gently squeeze the tap on the top of this
filterandliftout.
Thisfilter holds soil and food residuesin the sumpareaand
prevents itfrom being redepositon the dishes during wash cycle.
Main filter
1
Coarse filter
2
Fine filter
3
2
3
1
Filter assembly
Thefilter efficiently
For best performance and results, the filter must be cleaned regularly. this reason, it isa goodidea to
remove the larger food particlestrapped in the filter aftereach washcycle by rinsing the semicircular filterand
cup under runningwater. Toremove thefilter device, pull thecup handle in the upwarddirection.
removes food particles from the wash water, allowing it to be recycled during the cycle.
For
The dishwasher must never beused without the filters.
Improper replacementof the filter may reduce the performancelevel of the appliance
and damage dishesand utensils.
1
2
Step 1 Turn the filter in anti-clockwisedirection,
then lift it up.
：
Step 2 lift the Main filterup：
3
Step 3 lift theFinefilter up：
When following this procedure from step1 to step 3, the filter system will be removed;
when following it from Step 3 to Step 1, the filter system will be installed.

The control panel can be cleaned by using a lightly dampenedcloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use agood appliance polish wax.
Never usesharp objects, scouring pads orharsh cleaners on any part of the dishwasher.
ProtectAgainst Freezing
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe andwater valve. (Use apan to catch the water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottomof the tub and use a spongeto soak up water in the sump.
please take frost protection measuresonthe dishwasher in winter. Every fter washingcycles,
please operate as follows time a
：
- Inspect the filtersfor blockingafter every time the dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Remove any foodremnants and
cleanthefilters underrunningwater.
Remarks:
Cleaning the Filter
CleaningThe Door
To clean the coarsefilter and the fine filter, use a cleaning brush. Reassemble thefilter parts as shownin the figures
on thelast page and reinsert the entire assembly in the dishwasher, positioning it in itsseat and pressing downwards.
The entire filter assembly shouldbe cleaned once a week.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted andtheperformance ofthe dishwashercouldbedecreased.
To clean theedge around thedoor,you should use only a soft warm, dampcloth.
To avoid penetrationof water into the door lock and electrical components,do not
use a spray cleaner of any kind.
Never use a spray cleaner toclean the door panel as it may damage the door lock
and electricalcomponents.
Abrasive agentsor some paper towels should not be used because of the riskof
scratching or leaving spots on the stainless steel surface.
Cleaning the SprayArms
If your dishwasher cannot work because of the ice,
please contact professional service persons.
It is necessary to clean the spray arms regularly for hard
water chemicalswillclogthesprayarmjetsandbearings.
To remove theupper spray arm, screw off the nut clockwise then
remove thearm.
To remove thelower spray arm, pull out the spray arm upward.
Wash thearms in soapy and warm water and use a soft brush to
cleanthejets. Replace them afterrinsing them thoroughly.

Itisrecommendthatyourun awashcycle with the
dishwasher empty andthen remove the plugfrom the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
sealstolastlongerandpreventodoursfromforming
withintheappliance.
If the appliance must be moved, tryto keep it in the
verticalposition.Ifabsolutelynecessary, itcanbe
positioned on its back.
Oneofthefactorsthatcauseodourstoforminthe
dishwasher is food that remains trappedin the seals.
Periodic cleaning with adamp sponge will prevent this
from occurring.
Ensure the voltage and frequencyof the power being correspondsto
those on the ratingplate. Only insert the plug into an electricalsocket which is earthed
properly. Ifthe electrical socket to which the appliance must be connected is not
appropriate fortheplug , replace the socket, ratherthan usingaadaptors or thelike as
they couldcause overheatingandburns.
Pleaselook at therating label to know the rating voltage and connect the dishwasherto the appropriate power supply.
Use the required fuse 10 amp,timedelay fuse or circuitbreakerrecommended and provide separate circuit serving
only this appliance.
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a
cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
Position the appliance in the desired location. The back should rest against thewall behind it, and the sides,
along the adjacent cabinets or walls.The dishwasher is equippedwith water supply and drain hoses that can
be positioned either tothe right or the leftsidesto facilitate proper installation.
Once the applianceis positionedfor levelling, the height of the dishwasher
may be alteredviaadjustment of the screwing level ofthe feet. In any case,
theappliance should notbeinclined more than 2 .
For personal safety:
DO NOT USEAN EXTENSION CORD ORAN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDERANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
After every wash, turn off the water supply to the
appliance and leave the doorslightlyopen sothat
moisture and odours arenot trapped inside.
Before cleaning orperforming maintenance, always
remove the plug from the socket.
Tocleantheexteriorandrubberparts ofthedishwasher,
donot use solventsor abrasive cleaningproducts.
Only use acloth with warm soapy water.
To remove spots orstains from the surface of the
interior,usea clothdampened withwaterana little
vinegar, or a cleaning product madespecificallyfor
dishwashers.
After EveryWash
Remove the Plug
No Solvents orAbrasive Cleaning Moving theAppliance
Seals
When not inUse for aLongTime