Canadian Spa CRS 1 User manual

Bottom mount cover lifter (CRS 1)
BEFORE BEGINNING ASSEMBLY,
CAREFULLY READ THE INSTRUCTIONS:
Place all parts in a cleared area and remove the
packing materials. Assembly requires two people.
For help identifying the small parts used in
assembly, use the Parts List.
Note: During assembly, make sure that all parts are
oriented as shown in the drawings. Tighten all parts
as you assemble them, unless instructed to do
otherwise.
ASSEMBLY REQUIRES THE FOLLOWING TOOLS
(not included): two (2) adjustable wrenches, one (1)
phillips screwdriver, one (1) hammer, one (1)
power drill with a 1/16 drill bit and a 1/4 drill bit.
Soapy water.
You will also need some silicone to apply to the screw
heads before installing the end caps. (optional)
Bottom Mount Cover Lifter - Operation
To remove the cover from the spa, fold the spa
cover (at the hinge) back over the upper cover
support arm.
Then, using your foot, step down upon the lower
cover support arm while holding onto the foam
padded upper support arm and the cover will lift up
and be placed behind the spa.

Bottom mount cover lifter - Parts list
(CRS 1)
1
9
2
3
4
5
6
7
8
9
10
11
12
13
Description
1. #2 Screw
2. Mounting bracket
3. Pivot arm 1/2” x 43” (13 x 1092mm.)
4. Pivot bolt
5. Metal washers
6. Locknut
7. Spacer block
Qty
24
2
2
2
4
2
4
Parts List
Description
8. Upper cover support arm 1/2” x 41” (13 x 1041mm.)
9. Lower cover support arm 1/2” x 41” (13 x 1041mm.)
10. Coupler
11. Screw end cap
12. #1 Screw
13. Corner foam
Qty
2
2
2
44
20
4
2
Screw guide
Bottom mount bracket
screws in cm
Bottom mount screw in
inches
Self tapping screw in cm Self tapping screw in
inches

To assemble & install:
1. Position the spa cover (in closed position) on the spa,
making sure that all four corners are properly positioned
and square on the spa.
2. Insert the side pivot bolts and a metal washer into the
mounting brackets. (Figure 1). Using the #1 screws,
attach the left and right mounting brackets to the
appropriate sides of the spa. Position bracket flush to
panel and 5” or 125 mm. from bottom of corner panel.
(See Figure 2.)
3. Connect the side pivot arms to the mounting brackets.
Attach the side pivot arms to the mounting brackets
with two spacer blocks, a metal washer, and a locknut.
Secure the bolt tightly on the back side of the
mounting bracket. Repeat this procedure for each
side. (See Figure 3.)
4. Slide two of the foam tubes on the corners of the
lower cover support arms (See Figure 4A). TIP: Try
dipping the foams in soapy water first to help installation.
Insert the long ends of the lower cover support arms into
both sides of the coupler piece and then slide the lower
cover support arms into the shorter of the side pivot
arms on each side (See Figure 4.)
5. Slide two of the foam tubes to the corners of the upper
cover support arms. Then slide the long end of the
upper cover support arms into either side of the
coupler piece and then slide the short end of the upper
cover support arms into the top of the side pivot arms.
(See Figure 5.) Note: The upper cover support arms and
the coupler will now be laying on top of the spa cover
along the fold.
6. Adjust and center the coupler piece and upper support
arms so that the coupler piece is lying parallel
(approximately 0.5”(13mm.) away from the lifter to the
spa cover’s hinge).
7. Once you have the lifter fitted to the size of your spa, use
the #2 screws to connect the arms together
Using the #2 screws, fasten support arms to the
coupler pieces. There will be six screws inserted into
each of the coupler pieces, three at each end.
There will be three screws inserted into each upper
cover support arm where it connects to the side
pivot arm and two screws inserted into the lower
cover support arms where they attach to the side pivot
arm. Use a touch of silicone on top of the screws to
apply the screw head covers on each screw
(See Figure 6.)
Note: Be sure to rotate the coupler Piece so that the
inserted screws are at a horizontal angle with the heads
facing the back of the spa.
Bottom mount cover lifter - instructions
(CRS 1)
Figure 1 Figure 4
Figure 4A
Figure 2
Figure 5
Figure 3
Slip the coupler
over the Lower
Cover Support Arm
Slip the coupler
over the lower
cover support arm
Figure 6
Three screws
on each side
of coupler
Two screws
on each side
of lower
support arms
Three screws
on each side
of lower
support arms
Three screws
on each side
of coupler

Bottom mount cover lifter
Quick assembly guide & Warranty (CRS 1)
Canadian Spa Company meets ISO 9001 Standards
When you purchase a hot tub from Canadian Spa Company, the
ISO 9001 certification assures world class excellence in
manufacturing and customer service.
24 MONTH WARRANTY
Canadian Spa Company warrants this product to be free from
defects in workmanship and material, under normal use and
service conditions, for a Limited Lifetime Warranty.
This warranty extends only to the original purchaser.
Canadian Spa Company obligation under this warranty is
limited to replacing or repairing, at Canadian Spa Company
option, the product at one of its authorized service centers.
All products for which warranty claim is made must be
received by Canadian Spa Company at one of its authorized
service centers with all freight and other transportation charges
prepaid, accompanied by sufficient proof of purchase.
All returns must be pre-authorized by Canadian Spa Company.
This warranty does not extend to any product or damage to a
product caused by or attributable to freight damage, abuse,
misuse, improper or abnormal usage or repairs not provided
by a Canadian Spa Company authorized service center, prod-
ucts used for commercial or rental purposes, or products used
as store display models.
No other warranty beyond that specifically set forth above is
authorized by Canadian Spa Company.
UK Office:
Canadian Spa Company
Canada House
Salbrook Road
Salfords, Redhill
Surrey, RH1 5GL, UK
T: [phone]
F: [phone]
www.canadianspacompany.co.uk
France Office:
Canadian Spa Company sarl
2 rue de la Moudrerie
27370 La Saussaye
France
T: [phone]
www.canadianspacompany.fr
Germany Office:
Canadian Spa Company GmbH
Lutzerathstrasse 127
51107
Koln
Germany
T: [phone]
www.canadian-whirlpools.de
US Office:
Canadian Spa Company
6848 Airport Rd
W Jordan Utah
84084
T: [phone]
www.canadianspacompany.com
North America Head Office:
Canadian Spa Company
99 Bronte Road, Suite 613
Oakville, Ontario
L6L 3B7
Canada
T: [phone]
F: [phone]
www.canadianspacompany.ca
Dubai / Middle East Office:
Canadian Spa Company
JAFZA 8, Office no.27
P. O. Box 26455
Dubai, UAE
T: + 9714 - 8815223
F: + 9714 - 8815224
www.canadianspacompany.co.uk
Screw in screws to location 1 Screw in screws to location 2 Finished ground support arm Assemble top support Finished top support
Top & botton support
configuration
Insert top arm support Line up top support .5” (13mm)
away from centre seam
Screw in side arms using self
tapping screws
Screw in centre coupler - at
a horizontal angle with screw
heads facing the back of the spa
Ensure bracket is level on both
sides
Mark drill holes & drill with
# 8 drill & screw brackets to
cabinet
Install pivot arm using nut,
blocks and washers
Slide on two foam grips &
assemble ground support arm
Add self tapping screws
07/06/13