Pooli OS030979B User manual

Article No: OS030979B
PRODUCT MANUAL

Contents
1. Prepare for Installation....................................................................................................................................1
1.1. Selection a Location............................................................................................................... 1
1.2. Delivery.................................................................................................................................. 1
2. Technical Parameter and Specification........................................................................................................... 2
2.1. Structure of the SPA............................................................................................................... 2
3. Wiring Instruction............................................................................................................................................3
3.1.Find the Electrical Box and the Inlet.......................................................................................3
3.2.Connect to your power supply................................................................................................3
4. Fill the SPA with water.....................................................................................................................................5
4.1. Preparation.............................................................................................................................5
4.2 Fill your SPA within the standard level................................................................................... 5
4.3 Additional Instruction: How to open/remove/change the filter?..........................................5
5. TP600 Control Panels...................................................................................................................................... 6
5.1. Main Menus........................................................................................................................... 7
5.2. Fill it up!..................................................................................................................................8
5.3. Spa Behavior...........................................................................................................................9
5.4. Temperature and Temp Range.............................................................................................10
5.5. Mode –Ready and Rest................................................................................................... 11
5.6. Show and Set Time-of-Day...................................................................................................12
5.7. Flip (Invert Display).............................................................................................................. 12
5.8. Restricting Operation........................................................................................................... 13
5.9. Unlocking..............................................................................................................................13
5.10. Hold (Standby)................................................................................................................... 14
5.11. Adjusting Filtration.............................................................................................................15
5.12. Light Timer Programming.................................................................................................. 16
5.13. Preferences........................................................................................................................ 17
5.14. Utilities and Information....................................................................................................19
5.15. Additional Utilities............................................................................................................. 20
5.16. General Messages.............................................................................................................. 24
6. Maintenance................................................................................................................................................. 31
6.1. How to drain the water from your SPA?.............................................................................. 31
6.2. Water quality........................................................................................................................31
7. Precautions of using the SPA outdoors......................................................................................................... 32
7.1 Environment of Using........................................................................................................ 32
7.2 Instructions and Requirements in Winter......................................................................... 32
7.3 The Low Temperature Protection Function.......................................................................32
8. Troubleshooting Guide..................................................................................................................................33

1
1. Prepare for Installation
1.1. Selection a Location
The SPA can be installed indoors and outdoors. When choosing a location, please take the following factors into
consideration:
*The weight of the SPA, including water and the user(s)
*Drainage facilities: The drainage facility should be able to handle the maximum water capacity of the SPA.
*Surface Condition
Please place the spa on a structurally sound and level surface that is large enough for the entire spa, for example, a
concrete pad, concrete pavers or bricks or a reinforced deck. The adequacy of the structural support for a spa placed
on a terrace, balcony, roof terrace or other elevated structure must be determined by a licensed structural engineer,
architect or contractor depending on local and state requirements.
Do not place the SPA in a sink to avoid water accumulation and damage.
The spa warranty will be voided if an improper installation is performed. Structural damage due to an inadequate or
improper foundation is not covered under warranty.
1.2. Delivery
The SPA is erected sideways, packaged in carton and plywood and securely attached to a pallet. Use a trolley, forklift
or similar tool to transport your SPA to the desired location.

2
2. Technical Parameter and Specification
Voltage
380V 50Hz
Electrical connection
3-phase, 16A
Hydraulic Pressure
0.1~0.2Mpa
Power of water pump
1500W*2pcs
Filter pump
250W*1pc
Power of heater
3000W *1pc
Power of air pump
300W*1pc
Colorful light
12V,100mA
Total Power
6550W
2.1. Structure of the SPA
Size
2200*2200*910mm
Pillow
3pcs
Shell
Aristech Acrylic (White)
Number of Seats
7
PS Skirt
Grey
5"rotating jet
3pcs
Filter
1pc
3.5"jet
3pcs
LED Light
1pc
3/4"jet
43pcs
Ozone
1pc
Air bubble jet
12pcs
Diverter valve
2pcs
Air control valve
1pc
Suction port
4pcs
Maximum water capacity
650L
Note
Air control valve
An air control valve will give you greater control over the power of the massage from your jets. The valve allows you to
adjust the amount of air mixing with the pressurized water in the jets. You can decide whether you want a light tissue
massage or a more forceful targeted hydrotherapy massage. Rotate the air valve handle clockwise to decrease air
injection, rotate counterclockwise to increase air injection.
Diverter valve
The diverter valves are used to adjust the flow of water around your spa, from one side of a seat to another, as well as
fully (or partially) shutting off your hot tub water flow.

3
3. Wiring Instruction
The SPA has been assembled before delivery, you only need to connect it to the power supply to use it.
There are two ways of connecting the wires for Balboa system: 220V one-phase and 380V three-phase. For a better
user experience, Pooli has chosen the 380V three-phase. There are 5 wires that need to be connected: 3 fire wires, 1
neutral wire and 1 ground wire.
3.1.Find the Electrical Box and the Inlet
The electric box is located inside the removable skirt board. You will find the following stickers on the board.
To open the skirt board, you need a pliers and a screwdriver.
1) Remove the gray screw cap around skirt board (use pliers if it’s tight) , remove the screw with a screwdriver.
2) Hold the bottom of the skirt board with both hands and pull it out. (Note: The weight of the skirt is about 5KG)
3.2.Connect to your power supply
1) Open the electric box, you will see a detailed circuit diagram attached to the back of the cover. Please refer to the
small picture in the bottom left corner (230V 3P 3*16A) to connect to 380V. As shown in the picture below:

4
2) Find the sticker below in the corner of the electrical box where it connects to your household wires. Follow
the instructions of "3 SERVICE 3X16A".
There are 5 wires that need to be connected (3 fire wires, 1 neutral wire and 1 ground wire). The first interface is
connected to the fire wire (BRN 3), the second interface is connected to the fire wire (BRN 1), the third interface is
connected to the neutral wire (BLU), and the fourth interface is connected to the fire wire (BRN 2). The ground wire
needs to be connected to the second interface outside. Please refer to the actual sticker if the sticker is different from
this manual.
3) When the wiring is completed, it should be as same as the picture below:
Important! A leakage protection switch with a current not less than 20A and a leakage current no more than 30MA
should be installed in current front-end.

2. Fill the SPA with water
2.1. Preparation
(1)Ensure that the spa is powered off.
(2)Double check the drain valve is closed in case of water leaking from the SPA. The drain valve is
located at the corner of the SPA cabinet. See 6.1 (page 31) for details.
(3)Take out the filter core to enable filling of the spa through the filter itself (See 4.3 How to
open/remove/change the filter?).
4.2 Fill your SPA within the standard level
*Please refer to the water level marker on your tub (as picture below) and make sure the water
is filled up within the standard range.
*Start all the pumps to test the system. See section 5. for the system instruction.
*Put the filter core back to the filter box. Please remove the protective film before use.
4.3 Additional Instruction: How to open/remove/change the filter?
1) Rotate the cover 90 degrees to remove the cover.
2) Untighten the filter core by rotating it counterclockwise.
3) Remove the filter core from the box.
OR
Put the new filter core into the box and tighten it by rotating.
4) Put the cover back in place.
5

TP600 Control Panels
User Interface and Programming Reference – Standard Menus
System Model:
Software Version:
BP-Series Systems BP6013G2
7.0 and later
Panel Model: TP600 Series
Software Version: 2.3 or later
JETS AUX LIGHT HEAT
JETS AUX LIGHT HEAT
6

Main Menus
Screen
P
SET RANGE
SET
While the Temperature is still
flashing, press Light.
SET RANGE
READY RANGE FLTR1
Screen
READY RANGE FLTR1
SET READYSET
1
2
Light Cycle (if enabled).
If the time of day is not
set, "TIME SETTING" will
appear in this menu.
Waiting several seconds in the Main Menu will allow the display to return to the Main Screen.
Most changes are not saved unless the "Light " button is pressed. Refer to the key above.
Navigation
Navigating the entire menu structure is done with 2 or 3 buttons on the control panel.
Some panels have separate WARM (Up) and COOL (Down) buttons, while
others have a single Temperature button. In the navigation diagrams
Temperature buttons are indicated by a single button icon.
Panels that have two Temperature buttons (Warm and Cool) can
use both of them to simplify navigation and programming where
a single Temperature icon is shown.
The LIGHT Button is also used to
choose the various menus and navigate each section.
Typical use of the Temperature button(s) allows changing the
Set Temperature while the numbers are flashing in the LCD.
Pressing the LIGHT button while the numbers are flashing will
enter the menus.
The menus can be exited with certain button presses. Simply waiting for
several seconds will return the panel operation to normal.
Indicates a Menu Item that
Depends on a Manufacturer
Configuration and
may or may not appear.
Power-up Screens
Each time the System powers up, a series of numbers is displayed.
After the startup sequence of numbers, the system will enter Priming Mode
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button(WARM (Up) and COOL (Down) buttons), used for “Action” .
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and ignores
any change to that menu item.
*****
7

Preparation and Filling
Fill the spa to its correct operating level.
After turning the power on at the main power panel, the top-side panel display will go through specific sequences. These
sequences are normal and display a variety of information regarding the configuration of the hot tub control.
Priming Mode – M019*
This mode will last for 4-5 minutes or you can manually exit the priming mode after the pump(s) have primed.
Regardless of whether the priming mode ends automatically or you manually exit the priming mode, the system will auto-
matically return to normal heating and filtering at the end of the priming mode. During the priming mode, the heater is
disabled to allow the priming process to be completed without the possibility of energizing the heater under low-flow or
no-flow conditions. Nothing comes on automatically, but the pump(s) can be energized by pushing the “Jet” buttons.
If the spa has a Circ Pump, it can be activated by pressing the “Light” button during Priming Mode.
Priming the Pumps
As soon as the above display appears on the panel, push the “Jets1” button once to start Pump 1 in low-speed. Also, push the
“Jets2” to turn 2nd pump on. The pumps will now be running to facilitate priming. If the pumps have not primed after 2
minutes, and water is not flowing from the jets in the spa, do not allow the pumps to continue to run. Turn off the pumps
and repeat the process.
Note: Turning the power off and back on again will initiate a new pump priming session. Sometimes momentarily turning
the pump off and on will help it to prime. Do not do this more than 5 times. If the pump(s) will not prime, shut off the
power to the spa and call for service.
Important: A pump should not be allowed to run without priming for more than 2 minutes. Under NO circumstances
should a pump be allowed to run without priming beyond the end of the 4-5 minute priming mode. Doing so may cause
damage to the pump and cause the system to energize the heater and go into an overheat condition.
Exiting Priming Mode
You can manually exit Priming Mode by pressing a “Temp” button (Up or Down). Note that if you do not manually exit the
priming mode as described above, the priming mode will be automatically terminated after 4-5 minutes. Be sure that the
pump(s) have been primed by this time.
Once the system has exited Priming Mode, the top-side panel will momentarily display the set temperature but the display
will not show the temperature yet, as shown below. This is because the system requires approximately 1 minute of water
flowing through the heater to determine the water temperature and display it.
Fill it up!
READY RANGE READY RANGE
or
8