Canadian Spa Rio Grande User manual

wwww.canadianspacompany.com
Rio Grande portable spa - Assembly Guide
Rio Grande inflatable spa
Take all the spa components out of the outer box and check your Instruction Manual that all the
following key components are present:
Box includes:
A) Spa /liner (with integral Control
Unit connectors) x1
B) Inflatable cover/lid x 1
C) Control unit with RCD plug x 1
D) Thermal cloth x 1
E) Thermal blanket x 1
F) Drain hose x 1
G) Spare Control Unit connector x 1
H) Filters x 2
I) Wallet includes: Instruction Manual,
Repair patch, DVD
J) Inlet/Outlet caps, Drain Stopper
K) Inflation hose
1
Parts:
65 cm
60 cm
60 cm
A
B
C
D
E F
G
H
I
J
K

wwww.canadianspacompany.com
2
Assembly:
Rio Grande portable spa - Assembly Guide
Inflating the spa:
Before assembling the spa make sure the site is level and clear of debris
and sharp objects.
Ensure the spa is fully inflated to the
maximum height either 24 or 29 inches
(depending on the model).
Before inflating the spa - plug the spa into the electrical power outlet.
Switch on power and press the ‘test’ button on the RCD.
Lay out your spa base on a clean, level area more than 2.5 square
metres and capable of supporting a weight of more than 300kg/m2.
Make sure the spa is placed next to the Control Unit ready for inflation.
Connect the inflation
hose to inflation port on
the spa. Make sure the
vent holes on the hose
are not covered when
inflating (see photos
right).
Press the Massage button on the Control
Unit to inflate the spa chamber. Press the
Massage button again to stop inflation.
1
2
3
4
5
6

3
wwww.canadianspacompany.com
Assembly:
Inflate the spa lid using the same inflation
procedure as the spa body.
Attaching the Control Unit:
Ensure that the Blower Check valve, located
under the Control Unit (see photo right), is tightly
securely. These can sometimes become dislodged
during shipping, and cause malfunctions.
7
Rio Grande portable spa - Assembly Guide
Next align/screw the
Connectors to the
Control Unit with the
appropriate input port(s)
on the spa as highlighted
(see symbols for correct
alignment).
8
8
On the inside of the spa there is an internal drain
plug. On the outside of the spa there is a drain
cap - ensure both are securely tightened before
filling the spa with water.
9
Next place a garden hose in the spa and fill with
cold water until reaching the water level
indicator printed on the spa inner wall. Note: Do
not fill with hot water as this will effect the preset
thermostat settings.
10
Now add the Thermal
cover and the spa lid to
retain heat - then secure
the locking straps prior to
heating.
11

wwww.canadianspacompany.com
4
Assembly:
The spa is now ready to heat. Just press the
heater button to commence heating.
12
Rio Grande portable spa - Assembly Guide
Locking the Spa Control Unit:
Locking the spa Control unit:
Lock the spa Control Unit by pressing the up and
down buttons simultaneously on the Control
panel. To unlock use the same procedure.
Cleaning/replacing the filter:
Cleaning the Filter:
Before opening the filter compartment, screw the stopper caps on to the
internal outputs within the spa, then open the filter compartment lid and
remove the filter. Clean the filter pleats with a Filter Brush. Replace with
the clean Filter and close the lid.
To order new Filters visit: http://www.canadianspacompany.co.uk
Filter Size: 108 x 95 x 53 mm.
(4 1/4 x 3 3/4 x 2 1/16”)

wwww.canadianspacompany.com
5
Rio Grande portable spa - Assembly Guide
Draining the spa:
Draining the spa:
Ensure the internal connector caps are screwed
on. Unplug the internal spa plug, then unscrew
the external Drain cap and attach the drainage
extension hose. Drain the spa.