C&C TECHNIC AVLINK HDM-LNW User manual

HDMI OVER IP
Extender
HDM-LNW
HDM-RNW
USER MANUAL V1.1
HDM-ENW
Package Contents-
! 1x HDM-LNW and HDM-RNW Unit
! 1 user manual
! 1x Power adapter DC 12V with lock
! 2x screws
! 4x foot pads
! 1x IR receiver cable
! 1x IR blaster cable (Peak Wavelength 940nm)
Any thing missed, please contact with your vendor.
Features
! HDTV resolution up to 1080p@60.
! HDMI signal up to 100 meter on HDTV.
! Use CAT.5/5E/6 cable to install easily.
! Support RS-232.
! HDMI Compliant.
! HDCP Compliant.
! RS-232 Extender.
! Supports Web server system setup.
Specifications
Function
HDM
-
LNW
HDM
-
RNW
HDMI Input Connector
1
(A-Type Female)
NONE
HDMI Output Connector 1 (A-Type Female)
LED indicators POWER
LINK RJ-45 Connector x 1
IR IN NONE 3.5ψ Stereo Jack
x 1
355g
IR OUT 3.5ψ Stereo Jack
x 1 NONE
IR Carrier Frequency 20KHz ~ 60KHz
BAUD RATE SETTING 3 PIN DIP SWITCH
DIP SW 8 PIN DIP SWITCH
Power Adapter (Min.) DC 12V (LOCKING JACK)
HDMI Output Max.
Resolution 1080p@60 (8Bits)
1080P@60 (8Bits)
HDMI Output (Color
Space) YCbCr 4:4:4 RGB
Cat.5e Cable Distance 100 meters (Max.)
RS-232 Connector DB9 Female x 1
Baud Rate 2400 up to 115200 bps; 8 data bits, 1
stop bit, no parity
Housing Metal
Weight 338g 330g
Dimensions (LxWxH) 120x75x33mm
-1-
FRONT VIEW
HDM-LNW
1. 1x HDMI Output Connector (A-Type Female)
2. 1x HDMI Input Connector (A-Type Female)
3. 8 Pin DIP Switch
4. Power jack (12V DC In)
HDM-RNW
1. 1x HDMI Output Connector (A-Type Female)
2. 8 Pin DIP Switch
3. Power jack (12V DC In)
REAR VIEW
HDM-LNW
1. Power LED
2. System Reset
3. Baud Rate Setting
4. IR Out
5. RS-232 (DB9 Female)
6. Link (RJ-45 Connector)
-2-

HDM-RNW
1. Power LED
2. System Reset
3. Baud Rate Setting
4. IR In
5. RS-232 (DB9 Female)
6. Link (RJ-45 Connector)
Installation
1. Turn off the HDMI source and HDMI display.
2. Connect the HDMI cable between the HDMI source and
the “HDMI IN” port of HDM-LNW.
3. Connect the HDMI cable between the HDMI display and
the “HDMI OUT” port of HDM-LNW / HDM-RNW.
4. Connect the CAT.5/5e/6 cables between the HDM-LNW
“LINK” port and the HDM-RNW “LINK” port of
extender.
5. Connect the power cord of HDM-LNW and HDM-RNW.
5. Turn on the HDMI source and display.
※HDM-LNW ID and HDM-RNW ID must be the same.
IR Receiver Cable Directions:
Put it into the HDM-RNW “IR IN” port and place the IR
Receiver Cable, so that you can point to it easily with your
IR remote controller.
IR Blaster Cable Directions:
Plug IR blaster cable plug into HDM-LNW “IR OUT” port, It
sits in front of the DVD receiver’s IR sensor, which is
located on the front-panel.
-3-
DIP Switch Setting
BAUD RATE SETTING
2400 OFF OFF OFF
4800 ON OFF OFF
9600 OFF ON OFF
19200 ON ON OFF
28800 OFF OFF ON
38400 ON OFF ON
57600 OFF ON ON
115200
ON ON ON
ID
ID 0 OFF OFF OFF OFF OFF OFF
ID 1 ON OFF OFF OFF OFF OFF
.
.
ID 7 ON ON ON OFF OFF OFF
.
.
ID 63
ON ON ON ON ON ON
Technical Specifications Output Signal
-4-
Pin #
Signal
Pin #
Signal
1 TMDS Data 2+ 11 TMDS Clock Shield
2 TMDS Data 2 Shield 12 TMDS Clock -
3 TMDS Data 2- 13 CEC
4 TMDS Data 1+ 14 Reserved
(N.C. on device)
5 TMDS Data 1 Shield 15 SCL
6 TMDS Data 1- 16 SDA
7 TMDS Data 0+ 17 DDC/CEC Ground
8 TMDS Data 0 Shield 18 +5 Power
9 TMDS Data 0- 19 Hot Plug Detect
10 TMDS Clock+
Wiring Information & Coding
Conductor
Identification
RJ
-
45 Pin
Assignment
Color Code for
Conductor
Pair 1 5 White-Blue
4 Blue
Pair 2 1 White-Orange
2 Orange
Pair 3 3 White-Green
6 Green
Pair 4 7 White-Brown
8 Brown
-5-

Support Resolution
Resolution Frequency(Hz)
640x480 60
800x600 60
1024x768 60
1280x768 60
1280x800 60
1280x960 60
1280x1024 60
1360x768 60
1366x768 60
1440x900 60
1400x1050 60
1440x1050 60
1600x900 60
1680x1050 60
480i 60
480p 60
576i 50
576p 50
1080i 50/60
1080p 25/30/50/60
720p 50/60
-6-
Web server system setup
HDM-LNW (Server side)
Web setting address as below:
http://IP address (Default IP address TX board: 169.254.x.x
when no DHCP server assign IP address).
username: admin
password: 123456
HDM-LNW web server support feature: video bit
rate/resolution, DHCP/Fix IP, multicast group ID, update
f/w.
File to Upgrade Firmware: XXX.PKG
File to Upgrade Encoder Firmware: XXX.bin
HDM-RNW (Client side)
Web setting address as below:
http://IP address (Default IP address RX board:169.254.x.x
when no DHCP server assign IP address).
HDM-LNW side web server support feature: DHCP/Fix IP,
multicast group ID, update f/w.
File to Upgrade Firmware: XXX.PKG
Please don’t power off or reset/reboot device while board
f/w upgrade. HDM-ENW will reboot by self automatically
when upgrade successful and see below info in web page.
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
-7-