Candy EVOH 9713NA1 User manual

INSTRUCTION BOOK
EVOH 9713NA1
Heat Pump Tumble Dryer
English 2
Suomi
Italiano
50
62
Français 14
26
Dutch
Español 74

EN 2
3
3
3
3
3
4
4
4
4
5
5
5
5
6
7
7
7
7
7
8
9
10
10
11
11
11
12
12
12
12
12
13
13
13
13
10
10
10

INTRODUCTION
Use
Please check that the following items are
delivered with the appliance:
● Instruction manual
● Guarantee card
● Energy label
Please read and follow these instructions carefully and operate the machine accordingly. This
booklet provides important guidelines for safe use, installation, maintenance and some useful
advice for best
.
results when using your machine.
Keep all documentation in a safe place for future reference or for any future owners
Delivery nformationIUNPACKING THE PRODUCT
Dispose of the packaging safely. Make
sure it is out of the reach of childre ,it is a
potential source of danger.
n
Check that no damage has occurred to the
machine during transit. If it as, call for service
by GIAS.
h
EN 3
SAFETY REMINDERS

EN 4
European irective 2002/96/EDC
GIAS Service
If the appliance is not running properly or
breaks down, switch it off and disconnect the
plug from the socket. Consult GIAS Service for
possible repair.
Environmental Issues
Installation
The Laundry

Air Outlets in the Base
EN 5
Electrical Requirements
Adjusting the Feet
VENTILATION

EN 6
DRAIN HOSE : FITTING INSTRUCTIONS
WARNING! Switch off and remove the
tumble dryer plug from the electricity supply
before carrying out any work.
Fit the Hose as Follows:
1.Flip the machine
slowly to the right side.
2. The waste water
pipe is situated at the
right-hand side of the
machine (see the
picture). A grey hose
connects to the bridge
at the left hand side of
the machine. Using
pliers, remove the pipe
retaining clip from the
bridge.
3. Pull the hose off the
bridge connection.
4. Attach the black
hose from the kit,
(using the connector
a n d p i p e c l i p s
supplied), to the hose
removed from the
bridge connection.
5. Once the machine is
in place, check the
bottom to ensure that
the new hose does not
kink when pushing the
tumble dryer into
position.
6. Connect the new
drain hose to the waste
Water pipe.
7. Connect to the
m a i n s e l e c t r i c i t y
supply.
Caution: If the product
is in different side, wait
at least 4 hours before
switching on so that the
oil can flow back into
t h e c o m p r e s s o r .
Failure to do this could
result in damage to the
compressor.
To avoid emptying the water container after
each drying cycle, the water can be
discharged directly to a waste water drain pipe
(the same drainage system as household
sinks). Water Bye-Laws prohibit connection to
a surface water drain. The waste water drain
pipe should be located adjacent to the tumble
dryer.
The kit consists of:1 hose and 1 tap.
Do not install the product in a room where
there is a risk of frost occurring. At temperature
around freezing point the product may not be
able to operate properly: there is a risk of
damage if the water is allowed to freeze in the
hydraulic circuit (valves, hoses, pumps).
For a better product performance the ambient
room temperature must be between +2°C and
+35°C.
DRAIN HOSE KIT: FITTING INSTRUCTIONS

EN 7
PREPARING THE LOAD
Make sure that the laundry you are going to dry
is suitable for drying in a tumble dryer, as shown
by the care symbols on each item.
Check that all fastenings are closed and that
pockets are empty. Turn the articles inside out.
Place clothes loosely in the drum to make sure
that they don't get tangled.
Clothes Preparation
● Cottons Max. 7 kg
● Synthetics Max. 3,5 kg
Maximum Drying Weight
Do not overload the drum, large items when
wet can exceed the maximum admissible clothes
load (for example: sleeping bags, duvets).
Sort the Load as Follows
. .
.
Do Not Tumble Dry:
IMPORTANT: Do not dry articles which
have been treated with a dry cleaning fluid or
rubber clothes (danger of fire or explosion).
Energy Saving
During the last 15 minutes (roughly) the
load is always tumbled in cool air

EN 8
This machine has a special Sensor Dry to help you
choose your preferred programme simply by selecting the
level of dryness wanted.
For small loads and pre-dried clothes, please use a
Timing programme and select “Delicate fabrics” button to
lower the temperature inside the drum.
If the Sensor does not detect any item, this Dryer will work
for only 10 minutes before starting the Cool down phase.
If the load is too big or too wet, this Dryer will automatically
work for 3 hours and then start the Cool down phase.
At the end of each programme, there is always the Cool
Down phase: it is a cool-air refresh phase of around 15
minutes.
CONTROLS AND INDICATORS
Control Panel and Indicator Lights
SELECTING THE PROGRAMME
Programme
Selector
Time Selection
Button
Acrylic
Synthetic
Button
Anti-Crease
Button
Start/Pause
Button
Delay Start
Button
Empty Water
Indicator
Filter Care
Indicator Program
Display

EN 9
SELECTING THE PROGRAMME
PROGRAMME
Wool
Mix & Dry
Rapid 40’
Shirts
Time
Jeans
No Crease
Iron Dry
Perfect Home
Store Dry
Hang Dry
IDEAL FOR
Leave clothes slightly damp to allow easier ironing. Time: around 1h and
50 min.
Clothes you don’t need to iron, but just hang after the drying cycle. Time:
around 2h and 30 min.
Clothes you want to fold and store without ironing, e.g. shirts in mixed
fabrics, socks, baby clothes. Time: around 2h and 45 min.
Clothes you want completely dryed, e.g. towels, bathrobes, table clothes
or sheet. Time: around 3h.
To soften your woollen clothes or to simply refresh them after a long time in
the wardrobe. Time: 12 min.
To dry mixed cotton and synthetic clothes: save time and no need to
separate the washing and dry them in different cycles. Time: around 2h
(max 4 kg).
To dry shirts both cotton and synthetic fabrics. Time: 1h for 2kg of synthetic
shirts (around 10 shirts); 1h and 20 min for 3 kg of cotton shirts (around 10
shirts).
If you want to choose drying times, from 30 to 180 minutes. By selecting “20
min” you choose a “cool programme”, ideal to refresh clothes and to remove
eventual smells.
To dry up to 4 kg of Jeans (around 5 pairs). The programme works for around
2h, but timing can change according to the load and washing spin speed.
Jeans programme can only be used for 100% cotton items, please do not
mix colours nor dry jeans with embroideries or accessories.
Clothes you just need to refresh. Good for items of clothing which have been
left prior to ironing or if they have been dried outside or on radiators. This
programme has a specific Anti-Crease function that relaxes fibres and
makes easier ironing. Time: 9 min + 3 min cool down.
For dry, refreshed and ready to dress clothes in onyl 40 minutes. Sensor
system keeps under control the temperature to have always the best result.
Max 2 kg.

DOOR and FILTER
EN 10
Opening the Door
Pull on handle to open
the door.
To restart the dryer,
close the door and
press .
WARNING! When the tumble dryer is in
use the drum and door may be VERY HOT.
Never stop a tumble dryer before the end of the
drying cycle unless all items are quickly
removed and spread out so that the heat is
dissipated.
Filter Care Indicator
Lights when the filter
needs cleaning.
Check and clean the
main filter in the door
and the condenser
filters allocated in the
bottom of the dryer,If
the laundry is not
drying check that the
filter is not clogged. DO NOT USE WATER TO CLEAN THE FILTER.
Filter
IMPORTANT: To maintain the efficiency of the
dryer check that the fluff filter is clean before
each drying cycle.
Do not operate the dryer without the filters.
Clogged filters can increase the drying time
and cause damage which may result in
expensive repair costs.
1 . P u l l t h e f i l t e r
upwards.
2. Open filter as shown.
3.Gently remove lint
using a soft brush or
your fingertips.
4. S n a p th e fi l t e r
together and push
back into place.
To Clean the Condenser Filter
1 . R e m o v e t h e
kickplate.
2. Turn the two locking
levers anti-clockwise
and pull out the front
cover.
3. Gently remove the
filter frame and clean
any dust or fluff with a
cloth from the filter. Do
not use water to clean
the filter.
4. Remove the sponge
gently from its place
and then wash the
sponge by holding it
under a running tap
turning it so to remove
any dust or fluff.
5. Refit the front cover
ensuring it is in the
c o r r e c t w a y ( a s
indicated by the arrow)
and pushed firmly into
place. Lock the two
levers by turning them
clockwise.
6. Refit the kickplate.