Canon PowerShot S100 DIGITAL ELPH User manual

• Please read the precautions on the next page
before using your camera for the first time.
Camera User Guide
ENGLISH
This camera has three basic functions:
This guide explains the shooting and replay functions.
The downloading function is covered separately in the Software Starter Guide.
Shooting Replaying Downloading Images to a Computer

Precautions
Camera Body Temperature
If your camera is used for prolonged periods, the camera body may
become warm. Please be aware of this and take care when operating
the camera for an extended period.
About the LCD monitor
The LCD monitor is produced with extremely high-precision
manufacturing techniques. With more than 99.99% of the pixels
operating to specifications, less than 0.01% of the pixels may
occasionally misfire or appear as black, red or green dots. This has no
effect on the recorded image and does not constitute a malfunction.
Notice: Please ensure that you read and follow the handling and
safety precautions on pages 4 to 8 of this guide before
attempting to use the camera.
Disclaimer
• While every effort has been made to ensure that the information
contained in this guide is accurate and complete, no liability can be
accepted for any errors or omissions. Canon Inc. reserves the right to
change the specifications of the hardware and software described herein
at any time without prior notice.
• No part of this guide may be reproduced, transmitted, transcribed, stored
in a retrieval system, or translated into any language in any form, by any
means, without the prior written permission of Canon Inc.
• Canon Inc. makes no warranties for damages resulting from corrupted or
lost data due to a mistaken operation or malfunction of the camera, the
software, the CompactFlash™ cards (CF cards), personal computers,
peripheral devices, or use of non-Canon CF cards.
Trademark Acknowledgments
• Canon is a trademark of Canon Inc.
• CompactFlash is a trademark of SanDisk Corporation.
• Other names and products not mentioned above may be registered
trademarks or trademarks of their respective companies.
Copyright © 2000 Canon Inc. All rights reserved.

1
Table of Contents
Read This First
Please Read .......................................................................... 4
Safety Precautions ............................................................... 4
Warnings ............................................................................. 5
Cautions ............................................................................... 7
Preventing Mulfunctions .................................................... 8
Preparing the Camera
Guide to Components ......................................................... 9
Front View ..................................................................... 9
Back View .................................................................... 10
Operation Panel ............................................................ 11
Charging the Battery Pack ................................................ 12
Installing the Battery Pack ................................................ 14
Using the AC Adapter (Optional) ..................................... 16
Installing a CF Card ........................................................... 17
Attaching the Wrist Strap ................................................. 18
Setting the Date and Time ................................................ 19
Quick Start
Shooting ............................................................................ 20
Replaying ........................................................................... 21

2
Table of Contents
Basic Functions
Turning the Power On/Off ................................................ 22
Switching between the Shooting/Replay Modes ............. 23
Using the Optical Viewfinder ........................................... 23
Using the LCD Monitor ..................................................... 25
Shooting Mode ............................................................ 25
Replay Mode ................................................................ 26
Information Displayed on the LCD Monitor ..................... 26
Shooting Mode ............................................................ 26
Replay Mode ................................................................ 27
LCD Monitor Menus/Switching between Display Modes .. 28
Shooting Mode ............................................................ 28
Replay Mode ................................................................ 28
Pressing the Shutter Button .............................................. 30
Using the Zoom ................................................................. 31
Telephoto/Wide Angle .................................................. 31
Digital Zoom ................................................................ 32
Shooting
Selecting a Shooting Mode ............................................... 33
Functions Available in Each Shooting Mode .................... 34
Adjusting the Image Quality ............................................ 35
Using the Flash .................................................................. 36
Using the Self-Timer .......................................................... 37
Shooting Continuously ..................................................... 38
Shooting Close-Ups/Infinity Shots ..................................... 39
Adjusting the Exposure Compensation ............................ 40
Setting the White Balance ................................................ 41
Shooting in Stitch Assist Mode ......................................... 42
Framing a Subject ......................................................... 42
Shooting ...................................................................... 43
Shooting/Replaying with a TV Monitor ............................ 45

Table of Contents
3
Replaying/Erasing
Displaying Images Singly (Single Image Replay) .............. 46
Zooming an Image ....................................................... 46
Displaying Images in Sets of Nine (Multi Image Replay) . 47
Switching between Sets of Nine Images ........................ 47
Rotating Images in the Display ......................................... 48
Automating Playback (Auto Play) .................................... 49
Protecting Images ............................................................. 51
Print Settings (DPOF Settings) ........................................... 52
Displaying the Print Settings Menu ................................ 52
Setting the Print Style ................................................... 53
Selecting Images for Printing ......................................... 54
Resetting Print Settings ................................................. 56
Erasing Images .................................................................. 57
Erasing Images Singly .................................................... 57
Erasing All Images ........................................................ 58
Camera Settings
Displaying the Setup Menu .............................................. 59
Switching the Digital Zoom On/Off .................................. 60
Resetting the File Number ................................................ 61
Saving the Shooting Mode Setting .................................. 62
Switching the Beep On/Off ............................................... 63
Switching the AtuoPower Down Function On/Off .......... 64
Formatting CF Cards .......................................................... 65
Setting the Language ....................................................... 66
Appendices
Care and Maintenance of the Camera ............................. 67
Troubleshooting ................................................................ 68
List of Messages ................................................................. 72
Specifications ..................................................................... 74
Index .................................................................................. 76
Canon Customer Support Help Desk ................................ 78

4
Read This First
Please Read
Test Shots
Before you shoot images of subjects of importance to you, we strongly
recommend that you shoot several trial images to confirm that you are
operating the camera correctly. Please note that Canon Inc., its
subsidiaries and affiliates, and distributors of its digital cameras are not
liable for any consequential damages arising from any malfunction of
the Canon digital camera or CompactFlash™ card (CF card) resulting in
the failure of an image to be recorded or to be recorded in a format
that is machine sensible.
Warning Against Copyright Infringement
Please note that Canon digital cameras are intended for personal use
and must be used in a manner that respects international and domestic
copyright laws and regulations. Please be advised that in certain cases
the copying of images from performances, exhibitions, or commercial
properties by means of a camera or other device may contravene
copyright or other legal rights even if the image was recorded for
personal use.
Use of the Equipment in a Foreign Country
This camera is manufactured according to the specifications of the
country in which it is sold and the warranty is only effective in the
country of sale. If a problem arises while the camera is in use abroad,
please convey it back to the country of sale before proceeding with a
warranty claim to a Canon Customer Support Help Desk.
Safety Precautions
• Before using the camera, please ensure that you have read and
understood the safety precautions described below. Always ensure that
the camera is operated correctly.
• The safety precautions noted on the following pages are intended to
instruct you in the safe and correct operation of the camera and its
accessories to prevent injuries or damage to yourself, other persons
and equipment.
• In the next few pages, the term “equipment” refers primarily to the
camera and its power supply accessories.

Read This First
5
WARNINGS
• Do not aim the camera directly into the sun or at other intense light
sources which could damage your eyesight.
• Do not trigger the flash in close proximity to human or animal eyes.
Exposure to the intense light produced by the flash may damage
eyesight. In particular, remain at least one meter (39 inches) away from
infants when using the flash.
• Store this equipment out of the reach of children and infants.
Accidental damage to the camera or batteries by a child could result in
serious injury. In addition, placement of the wrist strap around the
child’s neck could result in asphyxiation.
• Do not attempt to disassemble or alter any part of the equipment that
is not expressly described in this guide. Disassembly or alteration may
result in high-voltage electrical shock. Internal inspections, alterations
and repairs should be conducted by qualified service personnel
authorized by your camera distributor or a Canon Customer Support
Help Desk.
• To avoid the risk of high-voltage electrical shock, do not touch the flash
portion of the camera if it has been damaged. Similarly, never touch
internal portions of the equipment which become exposed as a result
of damage. There is a risk of high-voltage electrical shock. Please take
the first opportunity to consult your camera distributor or a Canon
Customer Support Help Desk.
• Stop operating the equipment immediately in the event that it emits
smoke or noxious fumes. Failure to do so may result in fire or electrical
shock. Immediately turn the camera’s power off and remove the camera
battery or unplug the power cord from the electrical outlet. Confirm
that smoke or fume emissions have ceased. Please consult your camera
distributor or the closest Canon Customer Support Help Desk.
• Stop operating the equipment if it is dropped or the casing is
damaged. Failure to do so may result in fire or electrical shock.
Immediately turn the camera’s power off and remove the camera
battery or unplug the power cord from the electrical outlet. Please
consult your camera distributor or the closest Canon Customer Support
Help Desk.

6
Read This First
• Do not allow the equipment to come into contact with, or become
immersed in, water or other liquids. Do not allow liquids to enter the
interior. The camera has not been waterproofed. If the exterior comes
into contact with liquids or salt air, wipe it dry with a soft, absorbent
cloth. In the event that water or other foreign substances enter the
interior, immediately turn the camera’s power off and remove the camera
battery or unplug the power cord from the electrical outlet. Continued
use of the equipment may result in fire or electrical shock. Please consult
your camera distributor or the closest Canon Customer Support Help Desk.
• Do not use substances containing alcohol, benzene, thinners or other
flammable substances to clean or maintain the equipment. The use of
these substances may lead to fire.
• Do not cut, damage, alter or place heavy items on the power adapter
cord. Any of these actions may cause an electrical short circuit, which
may lead to fire or electrical shock. Replace a broken or damaged
power adapter cord.
• Do not handle the power cord if your hands are wet. Handling it with
wet hands may lead to electrical shock. When unplugging the cord,
ensure that you hold the solid portion of the plug. Pulling on the
flexible portion of the cord may damage or expose the wire and
insulation, creating the potential for fires or electrical shocks.
• Use of power sources not expressly recommended for this equipment
may lead to overheating, distortion of the equipment, fire, electrical
shock or other hazards. Use only the recommended power accessories.
• Do not place the batteries near a heat source or expose them to direct
flame or heat. Neither should you immerse them in water. Such
exposure may damage the batteries and lead to the leakage of
corrosive liquids, fire, electrical shock, explosion or serious injury.
• Do not attempt to disassemble, alter or apply heat to the batteries.
There is serious risk of injury due to an explosion. Immediately flush
with water any area of the body, including the eyes and mouth, or
clothing, that comes into contact with the inner contents of a battery.
If the eyes or mouth contact these substances, immediately flush with
water and seek medical assistance.
• Avoid dropping or subjecting the batteries to severe impacts that could
damage the casings. It could lead to leakage and injury.
• Do not short-circuit the battery terminals with metallic objects, such as
key holders. It could lead to overheating, burns and other injuries. Use
the supplied battery case to transport or store the battery pack.

Read This First
7
• Before you discard a battery, cover the terminals with tape or other
insulators to prevent direct contact with other objects. Contact with
the metallic components of other materials in waste containers may
lead to fire or explosions. Discard the batteries in specialized waste
facilities if available in your area.
• Use of batteries not expressly recommended for this equipment may
cause explosions or leaks, resulting in fire, injury and damage to the
surroundings. Use only recommended batteries and accessories.
• Use only the recommended battery charger to charge the Battery Pack
NB-1L rechargeable batteries. Use of chargers not expressly
recommended may result in overheating, distortion, fire or electrical
shock.
• Disconnect the battery charger or the compact power adapter from
both the camera and electrical outlet after recharging and when the
camera is not in use to avoid fires and other hazards.
• The camera terminal of the battery charger cord and the compact
power cord is designed for exclusive use with your camera. Do not use
it with other products or batteries. There is a risk of fire and other
hazards.
CAUTIONS
• Avoid using, placing or storing the equipment in places subject to
strong sunlight or high temperatures, such as the dashboard or trunk
(boot) of a car. Exposure to intense sunlight and heat may cause the
batteries to leak, overheat or explode, resulting in fire, burns or other
injuries. High temperatures may also cause deformation of the casing.
Ensure that there is good ventilation when using the compact power
adapter to charge the battery pack or power the camera.
• Do not store the equipment in humid or dusty areas. Storage in such
areas could lead to fire, electrical shock or other damage.
• Be careful not to bang the camera or subject it to strong impacts or
shocks that could lead to injury or damage the equipment when
wearing or holding it by the wrist strap.
• Be careful not to cover the flash with your fingers when shooting. In
addition, do not touch the surface of the flash after taking several
pictures in rapid succession. Either action could result in burns.
• If your camera is used for prolonged periods, the camera body may
become warm. Please take care when operating the camera for an
extended period as your hands may experience a burning sensation.

8
Read This First
Preventing Malfunctions
Avoid Strong Magnetic Fields
Never place the camera in close proximity to electric motors or other
equipment generating strong electromagnetic fields. Exposure to
strong magnetic fields may cause malfunctions or corrupt image data.
Avoid Condensation Related Problems
Moving the equipment rapidly between hot and cold temperatures
may cause condensation (water droplets) to form on its external and
internal surfaces. You can avoid this by placing the equipment in an
airtight, resealable plastic bag and letting it adjust to temperature
changes slowly before removing it from the bag.
If Condensation Forms Inside the Camera
Stop using the camera immediately if you detect condensation.
Continued use may damage the equipment. Remove the CF card and
battery or power cord (if connected) from the camera and wait until
the moisture evaporates completely before resuming use.
Extended Storage
When not using the camera for extended periods of time, remove the
battery pack and store the equipment in a safe place. Storing the camera
for extended periods with a battery pack installed will run down the
battery pack and may damage the camera. Please note, however, that
the date, time and other camera settings may reset to the default
settings if the battery pack has been removed for approximately three
weeks. Follow the instructions in this guide to reset the desired settings.

9
Preparing the Camera
Guide to Components
Front View
* Used to connect the camera to a TV or computer. Open the cover and
use the supplied video cable to connect to a TV or use the supplied
interface cable to connect to a computer.
=Optical Viewfinder Window ➜ p. 23
=AF Auxiliary Light Emitter
=Red-Eye Reduction Lamp ➜ p. 36
=Self-Timer Lamp ➜ p. 37
=Flash ➜ p. 36
=DIGITAL/VIDEO OUT
Terminal* ➜ p. 45
=DIGITAL/VIDEO
Terminal Cover
=Lens

10
Preparing the Camera
Back View
=CF Card Slot Cover ➜ p. 17
=Strap Holder ➜ p. 18
=Battery Cover ➜ p. 14
=Optical Viewfinder ➜ p. 23
=Lock for the CF Card Slot Cover ➜ p. 16
=LCD Monitor ➜ p. 25
=Tripod Socket
=DC Coupler Terminal Cover ➜ p. 16

Preparing the Camera
11
Operation Panel
Indicators
• The indicators will light or flash when the main switch is pressed or at
various stages as the shutter button is pressed.
Upper Indicator
Green: Ready to record
Flashing Green: During camera warm-up / Recording to CF card /
Reading CF card / Deleting CF card images
Red: Ready to record with flash
Flashing Red: Ready to record but the camera blur warning /
low light warning is flashing
Lower Indicator
Orange: Macro mode
=(Macro) / (Infinity) / (Right) Button
➜ p. 39
=(Continuous) / (Self-Timer) / (Left) Button
➜ p. 37
=(Flash) / (Set) Button ➜ p. 36
=Indicators =Main Switch ➜ p. 22
=Shutter Button ➜ p. 30
=Zoom Lever ➜ p. 31
=Mode Switch ➜ p. 23
=(Display) Button
➜ p. 25
=(Menu) Button

12
Preparing the Camera
Charging the Battery Pack
Recharge the battery pack with battery charger CB-2L or CB-2LE
the first time you use the camera or when the “Change the battery
pack” message is displayed.
Battery charger model names and types vary by region.
• Insert the battery pack into the charger as shown and plug the
charger into an electrical outlet.
• The charging indicator will flash red while the battery pack is
charging. It will change to a steady red when the charge is
complete.
• After charging, unplug the battery charger and remove the
battery pack from it.
• The battery pack utilizes lithium ion cells, avoiding the need to
completely use or discharge the battery charge before recharging it.
You may recharge the battery at any charge state without
permanently reducing its capacity.
• It takes approximately 120 minutes to charge a battery pack fully
from a fully discharged state. (Based on standard Canon testing
conditions) Please charge it at an ambient temperature ranging
between 5 and 40 ºC (41 and 104 ºF).
• Charge times may vary according to the ambient temperature and
the charge state of the battery pack.
• To protect and prolong the life of the battery pack, do not
charge it for longer than 24 hours at a time.
CB-2L CB-2LE
AC Power Cord

Preparing the Camera
13
Handling Precautions
• Do not charge the battery pack in poorly ventilated areas.
• Do not charge batteries other than Battery Pack NB-1L in this charger.
• The battery pack continues to discharge a minimal portion of its
power while installed in the camera, even with the camera power off.
This will shorten battery life. To conserve the battery pack, remove it
from the camera during extended periods of disuse and store it in its
case in a cool, dry place. Recharge it fully before using it again.
• If the performance of the battery pack diminishes substantially even
when it is fully charged, the battery pack should be replaced.

14
Preparing the Camera
Installing the Battery Pack
Install rechargeable Battery Pack NB-1L in the camera as shown below.
• Please recharge the battery pack (➜ p. 12) before you use it for
the first time.
Battery Lock
• Slide the battery cover in the
direction of the arrows.
• Press the battery lock while inserting
the battery pack all the way in until
the lock clicks.
• To remove the battery pack, press the
battery lock and pull the battery pack
out.
• Slide the battery cover closed.
• The camera contains a built-in rechargeable lithium battery to
save the date and time settings whenever the main battery is
removed. The main battery and AC adapter (optional) recharge
this battery whenever the camera is powered by them. When you
first purchase the camera, please leave the main battery in the
camera for approximately four hours or plug in the AC adapter
(optional) for that length of time. This battery will recharge even
when the camera’s main switch is set to Off.
• If the Set Date/Time menu displays when the main switch is
turned on, the charge of the built-in lithium battery is low. Please
follow the procedure in the previous paragraph to recharge it.

Preparing the Camera
15
• Never open the battery cover or remove the battery pack when the
main switch is on.
• Remove the battery pack from the camera when the camera is not
in use. Please note, however, that the date, time and other camera
settings may reset to the default settings if the battery pack has
been removed for approximately three weeks.
• Please use the AC adapter (optional) for this camera for extended
periods of use (➜p. 16).
Battery Performance
Recordable Images Replay Time
LCD Monitor On LCD Monitor Off
Battery Pack NB-1L Approx. 85 shots Approx. 270 shots Approx. 50 min.
(fully charged)
• The actual performance may vary from the above data according to the
shooting conditions and the shooting mode.
• At low operating temperatures, the battery performance may drop and the
battery icon may appers sooner than at high temperatures. To improve
performance at these temperatures, warm the battery in your pocket just
before using it in the camera.
<Test Conditions>
Shooting: 23 ºC (73 ºF), (Fine / Large), zoom used, flash used one in four
shots
Replay: 23 ºC (73 ºF), continuous replay, 3 seconds per image
Battery Pack Charge
The following icons and messages will display when the charge of
the battery pack is low.
Battery pack charge is low. Recharge it as soon as possible
before it is required for an extended period.
When the LCD monitor is off, this icon will display when you
press the , / or / button.
Battery charge is insufficient to operate the camera. Replace
the battery pack immediately.
Change the
battery pack

16
Preparing the Camera
Using the AC Adapter (optional)
It is recommended that you use the optional Canon AC adapter Kit
ACK300, which includes the Compact Power Adapter CA-PS300, the
DC Coupler DR-300 and the power cord, when using the camera for
extended periods of time to shoot or connect to a computer.
• Turn the camera power off before connecting or disconnecting
the AC adapter.
Compact Power Adapter
CA-PS300
DC Coupler
DR-300
• Connect the power cord to the
compact power adapter first and
then plug the other end into the
electrical outlet.
• Open the battery cover and press the
battery lock in the direction shown
while inserting DC Coupler DR-300.
Insert the DC coupler all the way in
until the battery lock clicks. Slide the
battery cover closed.
• Open the DC coupler terminal cover
and attach the cord to the DC
terminal.
• After you have finished using the
camera, unplug the AC adapter from
the electrical outlet.
Battery
Lock

Preparing the Camera
17
Installing a CF Card
Turn the camera power off and insert the CF card with the
following procedures.
• Slide the lock down and open the CF
card slot cover.
• Insert the CF card until the slot’s eject
button fully extends. Close the CF
card slot cover.
• To remove the CF card, push the eject
button and pull the CF card out.
CF Card Eject Button
CF Cards and Estimated Capacities (Recordable Images)
Quality FC-8M FC-16M FC-30M FC-48M
Super-Fine / Large ( 1600 x 1200 pixels )4 9 20 31
Fine / Large ( 1600 x 1200 pixels )12255279
Fine / Small ( 640 x 480 pixels ) 46 92 192 289
• These figures reflect standard shooting conditions established by Canon.
Actual totals may vary according to the subject, shooting conditions and
shooting mode.

18
Preparing the Camera
Handling Precautions for CF Cards
• CF cards are high-precision electronic devices. Do not bend them,
apply force to them, or subject them to shocks or vibration.
• Do not attempt to disassemble or alter a CF card.
• Moving a CF card rapidly between temperature extremes will cause
condensation to form in the card and lead to a malfunction. To avoid
condensation, place the CF card in a sealed plastic bag before
moving it into a different temperature zone and allow it to adjust
slowly to the new temperature. If condensation forms on the CF
card, store it at room temperature until the water droplets have
evaporated naturally.
• Place the CF card in the supplied case for storage.
• Do not use or store CF cards in the following types of location.
- Locations subject to strong magnetic fields
- Location subject to dust or sand
- Locations subject to high humidity and high temperatures
• Never open the CF card cover while the main switch is on.
• When the indicator flashes green, the camera is recording, reading
or deleting images to and from the CF card. Never turn off the
power or remove the CF card while the indicator flashes green.
• Please note that CF cards from other manufacturers, or CF cards
which have been edited with application software using other
formats, may not operate correctly in the camera.
Attaching the Wrist Strap
• Thread the small loop of the wrist strap
through the strap holder on the
camera and pull the large loop through
the small loop until the small loop fits
snugly against the strap holder.
• Be careful not to wave the camera
about or catch it on other items
when dangling it from the wrist
strap.